Table of Contents
Advertisement
Mobile Phone
A
CAUTION
B
Metallic objects located between the cellphone and
C
the charging pad during wireless charging can be-
D
come extremely hot and may cause injuries or ma-
terial damage.
E
e Do not place any objects between the cellphone
F
and the charging pad.
G
b b Function enabled in the PCM (SET
H
settings e Phone e Wireless charging
I
– or –
e Options
PHONE
J
Phone e Wireless charging
K
b b Wireless charging according to the Qi standard
supported by the cellphone.
L
e Place cellphone on the marked area in the
M
smartphone tray.
N
The
symbol appears in the status bar of the
PCM when the function is activated or when
O
wireless charging is active.
P
The charging power may vary depending on the
cellphone.
Q
R
S
T
U
V
W
X
Y
Z
182
Metallic objects in the
smartphone tray
An alternating magnetic field is used during wireless
charging. Interactions are possible, such as irritation
of the sensory organs or malfunction of active im-
plants (e.g. pacemakers, infusion pumps or neuro-
stimulators) or interference with passive implants (e.
g. artificial joints).
e Always maintain a minimum distance of 4 inches
(10 cm) from the charging pad.
e Phone
This distance complies with the limit values for
long-term exposure according to ICNIRP1998.
e If you have an implant, please consult a medical
e Phone settings e
specialist if you have any questions.
).
For USA:
This is a CONSUMER device.
– BEFORE USE, you MUST REGISTER THIS DEVICE
with your wireless provider and have your pro-
vider ´ s consent. Most wireless providers con-
sent to the use of signal boosters. Some
providers may not consent to the use of this de-
vice on their network. If you are unsure, contact
your provider.
– In Canada, BEFORE USE, you must meet all re-
quirements set out in ISED CPC 2 1 05.
– You MUST operate this device with approved
antennas and cables as specified by the manu-
facturer. Antennas MUST be installed at least 20
cm (8 inches) from any person.
– You MUST cease operating this device immedi-
ately if requested by the FCC (or ISED in Canada)
or a licensed wireless service pr ovider.
– WARNING. E911 location information may not
be provided or may be inaccurate for calls served
by using this device.
Link to ISED CPC-2-1-05:
Information
https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/h_
sf06136.html
– CPC-2-1 – Fixed and Land Mobile
– CPC-2-1-05 - Zone Enhancers
FCC RF Exposure Statement
This equipment complies with FCC radiation expo-
sure limits set forth for an uncontrolled environment.
End users must follow t he specific operating in-
struction for satisfying RF exposure compliance. This
transmitter must not be co located or operating in
conjunction with any other antenna or transmitter.
Any changes or modifications not expressly ap-
proved by Molex could void the user's authority to
operate this equipment.
FCC ID: RK7MBC NAR2
IC: 4774A MBCNAR2
This device complies with part 15 of the FCC rules
and with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following
two conditions:
– This device may not cause harmful interference.
– This device must accept any interference re-
ceived, including interference that may cause
undesired operation.
FCC ID: RK7193-00
IC: 4774A-19300
Any changes or modifications not expressly ap-
proved by Molex CVS Dabendorf GmbH could void
the user's authority to operate this equipment.
NOTE: This device complies with RF exposure
guidelines of the FCC rules and with Industry Canada
license-exempt RSS standard(s) at a distance of
1.7in/4.2cm under normal use case conditions.
This Signal Booster fulfills the FCC requirements for
the Network Protection Standard (NPS). It incorpo-
rates features to prevent harmful interference to
wireless networks like:
Advertisement
Table of Contents
