Battery Charging; Battery Exchange; Cleaning And Care - Polaris PVCS 7090 HandStick PRO Aqua Operation Manual


If necessary, follow steps 1-2 or 1-3 from the previous section.

To turn on the device, press the on/off button (see. DESCRIPTION OF THE DEVICE).

The device has three operating modes:
I (low suction speed and power, long operation time, the mode is started by default when the device is turned on);
II (average speed and suction power, average operating time);
III (high suction speed and power).
To select mode II and mode III, press the mode switch button for the desired number of times after turning on the device (see
DEVICE).
To save battery power, mode I is recommended. If the cleaning efficiency is not sufficient (in the case of severe littering), select the following mode.

The electric brush is designed to collect household dust from the floor and carpeting using a rotating bristle roller. Its construction is very sensitive to clogging
with long hair, wool, thread, etc. In case of clogging, immediately stop using the vacuum cleaner and take measures to clean the bristle roller (see the section

"CLEANING AND CARE").


* The wet cleaning nozzle is designed for wet cleaning of the room. To do this, attach the rag from the kit to the bottom of the wet cleaning container, pour
water into the neck of the water tank. Close the lid. Secure the wet cleaning nozzle to the back of the floor brush so that the latches on the nozzle and the floor
brush connect until they click. Press the water supply button to start the water flow to the rag Fig. 13

When cleaning the dust, combined with wet cleaning, you should perform the main movement of the brush forward, so that when the brush moves, first
remove the dust, and then wipe the cleaned area with a damp cloth.

After cleaning, press the water supply button on the nozzle. Disconnect the wet cleaning nozzle from the brush. Do not leave water in the tank.

* To turn off the device, press the on/off button again.

To clean the floor in hard-to-reach places (under the table), press the lock 19 Fig. 1. The pipe will open in a bent position, which will allow you to clean the
hard-to-reach surface without unnecessary effort.
Furniture cleaning

Make sure that the battery is charged, the adapter is disconnected from the mains and from the device, the filter and dust collector are properly emptied of dust
(see the section "CLEANING AND CARE"). Do not use the vacuum cleaner with a filter clogged with dust and a dust bag, this may lead to failure of the
vacuum cleaner.

Attach an optional accessory to the suction port.
The mini-brush is suitable for cleaning furniture upholstery, and the crevice nozzle is suitable for cleaning hard-to-reach places.

To turn on the device, press the on/off button.

Change the mode if necessary (see the description in the previous section).

To turn off the device, press the on/off button again.
In the event of a spontaneous stop of the motor during operation of the device, charge the battery and clean the filter and dust collector.
Additional attachments can be stored in a special wall mounting compartment. To do this, fix the mount on the wall as shown on the figure. Additional accessories are
inserted into special racks. You can also use a floor stand for vertical storage of the vacuum cleaner on the floor. Fig. 6

BATTERY CHARGING

Attention!
The battery included in the set may be low of charge. Before the first use, fully discharge the battery and then fully charge it.
Do not charge the battery and do not store the battery in air temperatures below 5 °C and above 40 °C.
Before connecting the device's adapter to the network, check that its technical specifications (see the "Technical Specifications" section) correspond to the
network parameters.
The first charging of the battery can take 8-10 hours.
Further, 4 hours will be enough for a full charge.
It is recommended to charge the battery only when the device signals its imminent discharge (red glow of the charge indicator on the battery case). Do not interrupt the
battery charging process until the battery is fully charged. This will extend the battery life.
The battery can only be charged using the adapter included in the set of the device. The battery can be installed on the device or removed from the device before
charging.
Fig. 7
1. Insert the adapter plug into the battery socket.
2. Plug in the adapter. A red signal will light up on the battery charge indicator, indicating the beginning of the charge. When the battery is fully charged, the
indicator will glow green.
3. You can charge the battery separately from the vacuum cleaner.
Attention! The adapter may become warm during charging - this is normal.
The device does not turn on with the charging adapter connected.

BATTERY EXCHANGE

This model of the vacuum cleaner uses removable battery.
If you need to remove the battery, press the battery disconnect button when the device is turned off and remove the battery by sliding it down the sliders.
Attention: removing/installing the battery while the device is operating or while charging is prohibited!
The battery capacity and the continuous operation time of the device decrease over time - this is normal.
If you need to diagnose or replace the battery, contact an authorized service center of POLARIS (the list of service center addresses is included in the package and is also
available on the website www.polar.ru)
CLEANING AND CARE
1. Turn off the device, unplug it, and disconnect the adapter from the device if it is connected.
2. Do not immerse the device and charger in water or other liquids.
3. Do not use abrasive materials or organic solvents to clean the device.
4. Wipe metal parts with a clean, dry cloth.
5. Wipe the plastic parts of the appliance with a damp, wrung cloth. There should be no drops of water.
6. Keep the device in a cool, dry place.
Cleaning the dust container
The dust container and filters should be cleaned after each use of the vacuum cleaner.
Do not use a vacuum cleaner with filters clogged with dust, this may cause the failure of the motor.
1. Turn off the device. The adapter must be disconnected from the mains and disconnected from the device.
2. Press the release button of the electric brush on the vacuum cleaner. Disconnect the brush from the pipe. Press the accessory release button. Disconnect the pipe
from the suction pipe. Fig. 8
DESCRIPTION OF THE
- 26 -