Connect A Fuse To The Input Side (Primary Side) - YASKAWA CR700 Quick Start Manual

15 European Standards
Model Terminal
R/L1, S/L2, T/L3
R1/L11, S1/L21, T1/L31
U/T1, V/T2, W/T3
4453 -, +1
+3
R/L1, S/L2, T/L3
R1/L11, S1/L21, T1/L31
U/T1, V/T2, W/T3
4605 -, +1
+3
*1 For IP20 protection, use wires that are in the range of applicable gauges.
*2 Remove insulation from the ends of wires to expose the length of wire shown.
*3 For wire gauges more than 30 mm
*4 Install an ELCB with this wire gauge to maintain compliance with IEC/EN 61800-5-1:2007.
*5 Terminals - and +1 have two screws. The Recommended Gauge is the wire gauge for one terminal.
*6 A junction terminal is necessary to connect a braking resistor unit (LKEB-series) to terminals B1 and B2.
■

Connect a Fuse to the Input Side (Primary Side)

The drive circuit protection must comply with IEC/EN 61800-5-1:2007 for protection against a short circuit in the
internal circuitry. Connect semiconductor fuses on the input side for branch circuit protection.
WARNING Electrical Shock Hazard. After the drive blows a fuse or trips an RCM/RCD, do not immediately energize the
drive or operate peripheral devices. Wait for the time specified on the warning label at a minimum and make sure that all
indicators are OFF. Then check the wiring and peripheral device ratings to find the cause of the problem. If you do not know the
cause of the problem, contact Yaskawa before you energize the drive or peripheral devices. If you do not fix the problem before
you operate the drive or peripheral devices, it can cause serious injury or death.
Three-Phase 200 V Class
Table 15.4 Factory-Recommended Branch Circuit Protection (200 V Class)
88
Applicable Gauge
Recomm. Gauge
(IP20 Applicable
mm 2
120 × 4P
95 × 4P
(120 - 150 × 4P)
95 × 4P
70 × 4P
95 × 2P
120 × 4P
95 × 4P
(120 - 150 × 4P)
95 × 4P
70 × 4P
95 × 2P
2 , tighten to a tightening torque of 4.1 N∙m to 4.5 N∙m (36 lbf∙in to 40 lbf∙in).
Drive Model
2003
2005
2008
2011
2014
2018
2025
2033
2047
2060
2075
2088
Wire Stripping
Length *2
*1
Gauge )
mm
mm 2
70 - 150 × 4P
-
(150 × 4P)
70 - 150 × 4P
-
95 - 185 × 4P
-
(185 × 4P)
35 - 95 × 4P
-
(95 × 4P)
60 - 150
-
(-)
70 - 150 × 4P
-
(150 × 4P)
70 - 150 × 4P
-
95 - 185 × 4P
-
(185 × 4P)
35 - 95 × 4P
-
(95 × 4P)
60 - 150
-
(-)
Semiconductor Protection Fuse Rated Current
YASKAWA TOEPC71061723A YASKAWA AC Drive CR700 Quick Start Guide
Terminal Screw
Size Shape
M12 Hex self-locking nut
M12 Hex self-locking nut
M12 Hex self-locking nut
M12 Hex self-locking nut
M12 Hex bolt (slotted)
M12 Hex self-locking nut
M12 Hex self-locking nut
M12 Hex self-locking nut
M12 Hex self-locking nut
M12 Hex bolt (slotted)
Manufacturer: EATON/Bussmann
FWH-45B
FWH-45B
FWH-45B
FWH-100B
FWH-100B
FWH-100B
FWH-125B
FWH-150B
FWH-200B
FWH-225A
FWH-225A
*1
FWH-250A
FWH-225A
*1
FWH-250A
Tightening
Torque
N∙m (lbf∙in)
35
(310)
35
(310)
35
(310)
35
(310)
32 - 40
(283 - 354)
35
(310)
35
(310)
35
(310)
35
(310)
32 - 40
(283 - 354)