Factory-Recommended Branch Circuit Protection - YASKAWA CR700 Quick Start Manual

Recomm. Gauge (AWG, kcmil)
Model
R/L1, S/L2, U/T1, V/T2,
T/L3 W/T3
-
-
4260
3/0 × 2P 3/0 × 2P
-
-
-
4304
250 × 2P 250 × 2P
-
-
-
4371
300 × 2P 300 × 2P
-
-
-
4414
- 4/0 × 4P
250 × 4P
-
4453 - 4/0 × 4P
250 × 4P
-
-
-
4605
300 × 4P 300 × 4P
-
*1 Contact Yaskawa or your nearest sales representative for more information.
■

Factory-Recommended Branch Circuit Protection

Use branch circuit protection to protect against short circuits and to maintain compliance with UL61800-5-1.
Yaskawa recommends connecting semiconductor protection fuses on the input side for branch circuit protection.
Refer to Table 16.5 to Table
WARNING
Electrical Shock Hazard. After the drive blows a fuse or trips an RCM/RCD, do not immediately energize the
drive or operate peripheral devices. Wait for the time specified on the warning label at a minimum and make sure that all
indicators are OFF. Then check the wiring and peripheral device ratings to find the cause of the problem. If you do not know the
cause of the problem, contact Yaskawa before you energize the drive or peripheral devices. If you do not fix the problem before
you operate the drive or peripheral devices, it can cause serious injury or death.
• 200 V Class
Use the fuses specified in this document to prepare the drive for use on a circuit that supplies not more than
100,000 RMS and not more than 240 Vac when there is a short circuit in the power supply.
YASKAWA TOEPC71061723A YASKAWA AC Drive CR700 Quick Start Guide
-, +1 +3
- - -
- - 1/0 × 2P
- -
- 4/0 × 2P -
- - -
- - 3/0 × 2P
- -
- 350 × 2P -
- - -
- - 4/0 × 2P
- -
- 400 × 2P -
- - -
- - 3/0 × 4P
4/0 × 4P -
- - -
-
- -
3/0 × 4P
- -
-
- -
300 × 4P
- - -
- - 4/0 × 4P
- -
- 400 × 4P -
16.6for the recommended fuses.
Crimp
Terminal
Terminal
Screw Size
Model
2 R38-10
- R60-10
M10
- 80-10
- R100-10
1 R60-12
- 80-12
M12
- R150-12
- R200-12
1 R60-12
- R100-12
M12
- R150-12
- R200-12
1/0 R60-12
- 80-12
M12
- R100-12
- R150-12
2/0
80-12
-
- M12 R100-12
- R150-12
2/0 80-12
- R100-12
M12
- R150-12
- R200-12
16 UL Standards
Crimping Tool
Insulation
Cap Model
Tool Model Die Jaw
TD-224, TD-
TP-038
212
TD-225, TD-
TP-060
213
YF-1
YET-150-1
TD-227, TD-
TP-080
214
TD-228, TD-
TP-100
214
TD-321, TD-
TP-060
311
TD-323, TD-
TP-080
312
YF-1
YET-300-1
TD-325, TD-
TP-150
313
TD-327, TD-
TP-200
314
TD-321, TD-
TP-060
311
TD-324, TD-
TP-100
312
YF-1
YET-300-1
TD-325, TD-
TP-150
313
TD-327, TD-
TP-200
314
TD-321, TD-
TP-060
311
TD-323, TD-
TP-080
312
YF-1
YET-300-1
TD-324, TD-
TP-100
312
TD-325, TD-
TP-150
313
TD-323, TD-
TP-080
312
YF-1
TD-324, TD-
TP-100
312
YET-300-1
TD-325, TD-
TP-150
313
TD-323, TD-
TP-080
312
TD-324, TD-
TP-100
312
YF-1
YET-300-1
TD-325, TD-
TP-150
313
TD-327, TD-
TP-200
314
EN
115