Table of Contents
Advertisement
Operator's Manual: 405 SLD Seed Express
Each radio remote control handset transmitter is
designed to operate with a unique radio ID code
and RF channel sequence. Each control panel
5.4 WIRELESS REMOTE
TRANSMITTER
receiver is programmed to respond only to the
handset transmitter with the correct ID code/
Each radio remote transmitter is designed to
operate with a unique radio ID code and RF
RF channel sequence for which it is set. This
channel sequence. Each receiver is programmed
feature allows multiple systems to work in close
to respond only to the remote transmitter with the
proximity to one another without interference.
correct ID code/RF channel sequence for which
it is set. This feature allows multiple systems to
work in close proximity to one another without
If the handset goes out of range for more than
interference.
two seconds, all outputs except CONVEYOR
If the remote transmitter goes out of range for
will turn off as a safety feature.
more than two seconds, all outputs except
CONVEYOR will turn off as a safety feature.
In the event that the handset becomes damaged
In the event that a remote transmitter becomes
and a new one is needed, the control panel
damaged and a new one is needed, the receiver
receiver can be reprogrammed to respond to the
can be reprogrammed to respond to the new
new control. Refer to Section 4.3.9 (Page 4-11)
remote transmitter. Refer to "10.1.3 Remote
Control Transmitter and Receiver Synchronization"
on page 50 of this manual.
All of the normal functions of the seed tender
All of the normal functions of the seed tender can
can be controlled by the remote control handset.
be controlled by the remote transmitter.
a
c
d
g
h
Fig 18 - Remote control handset transmitter
3-10
Bulk Seed Tender
™
3.4 REMOTE CONTROL SYSTEM
5.4.1 Functions of Keypad Buttons
Use the buttons on the keypad to operate the
desired functions of the seed tender.
1
POWER (1)
Press Power button (1) to turn remote transmitter
ON. Press and hold the button to turn it OFF.
3
To save battery life, the remote transmitter will
automatically turn off when it is idle (no functions
are used) for a period greater than the sleep time
(default is 15 minutes). Refer to "10.1.4 Changing
Sleep Time on the Transmitter" on page 51 to
change the sleep time on the transmitter.
NOTE: The remote transmitter will NOT
automatically shut off as long as the receiver has
power applied to it.
ENG STOP (2)
Press Engine Stop button to turn OFF engine.
b
8
3
e
CONV (3)
The Conveyor button starts and stops the
conveyor belt. Press the INC button to start the
f
conveyor. Press STOP button to stop conveyor.
GATE 1 (4)
The Slide Gate 1 buttons open and close the slide
gate at the bottom of compartment 1. Press the
8
OPEN button to open the slide gate, and press
the CLOSE button to close the slide gate. The
i
opening can be varied to provide the desired flow
rate of seed onto the conveyor belt.
®
3.4.1 Functions of Handset Buttons:
Use the buttons on the control to operate the
functions of the seed tender.
a. POWER:
Press Power button (a) to turn ON the
handset. Press and hold the button to turn
it OFF.
To save battery life, the handset will automatically
turn off when it is idle (no functions are used) for
a period greater than the sleep time (default is
15 minutes). Refer to Section 4.3.10 (Page 4-11)
to change the sleep time.
The remote control handset will NOT
automatically shut off as long as
the control panel receiver has
power applied to it.
1
b. ENG STOP:
Stop the engine with this button.
9
c. CONV - INC/STOP:
These Conveyor buttons start and stop the
conveyor belt.
The conveyor has 3 speeds. Press the INC
button once to start the conveyor at low
speed. Press the button again for medium
speed, and a third time for high speed. The
fourth time will return to low speed.
Note: The conveyor will start at the last
speed used once stopped, always return
9
conveyor belt speed to low before stopping.
2
4
5
Note:
7
6
2
4
10
5
7
6
10
29
Revised 08.2021
®
Advertisement
Table of Contents
