Hydraulic Fittings - MacDon R80 Unloading And Assembly Instructions
Pull-type rotary disc mower conditioner
Hide thumbs
Also See for R80:
- Operator's manual (104 pages) ,
- Operator's manual (124 pages) ,
- Manual (42 pages)
Table of Contents
Advertisement
D. HYDRAULIC FITTINGS
FLARE TYPE
FLARE
FLARESEAT
a. Check flare and flare seat for defects that
might cause leakage.
b. Align tube with fitting before tightening.
c. Lubricate connection and hand tighten swivel
nut until snug.
d. To prevent twisting the tube(s), use two
wrenches. Place one wrench on the connector
body and with the second tighten the swivel
nut to the torque shown.
NUT
TUBE
SIZE
THD
SIZE
SAE
ACROSS
SIZE
O.D.
NO.
FLATS
(in.)
(in.)
(in.)
3
3/16
3/8
7/16
4
1/4
7/16
9/16
1/2
5
5/16
5/8
9/16
6
3/8
11/16
8
1/2
3/4
7/8
10
5/8
7/8
1
12
3/4
1-1/16
1-1/4
14
7/8
1-3/8
1-3/8
* The torque values shown are based on lubricated connections
as in reassembly.
Form # 169080
NUT
BODY
RECOMMENDED
TURNS TO
TORQUE
TIGHTEN
VALUE*
(AFTER FINGER
TIGHTENING)
ft·lbf
N·m
Flats
Turns
6
8
1
1/6
9
12
1
1/6
12
16
1
1/6
18
24
1
1/6
34
46
1
1/6
46
62
1
1/6
75
102
3/4
1/8
90
122
3/4
1/8
O-RING TYPE
FITTING
SEAT
a. Inspect O-ring and seat for dirt or obvious defects.
A
B
b. On angle fittings, back off the lock nut until washer
(A) bottoms out at top of groove (B) in fitting.
c. Hand tighten fitting until back up washer (A) or
washer face (if straight fitting) bottoms on part
face (C) and O-ring is seated.
d. Position angle fittings by unscrewing no more than
one turn.
e. Tighten straight fittings to torque shown.
f.
Tighten angle fittings to torque shown in the
following table while holding body of fitting with a
wrench.
NUT SIZE
THD
ACROSS
SAE
SIZE
FLATS
NO.
(in.)
(in.)
3
3/8
1/2
4
7/16
9/16
5
1/2
5/8
6
9/16
11/16
8
3/4
7/8
10
7/8
1
12
1-1/16
1-1/4
14
1-3/16
1-3/8
16
1-5/16
1-1/2
20
1-5/8
1-7/8
24
1-7/8
2-1/8
* The torque values shown are based on lubricated connections as
in reassembly.
5
LOCKNUT
WASHER
O-RING
GROOVE
C
RECOMMENDED
TORQUE
TURNS TO TIGHTEN
VALUE*
(AFTER FINGER
TIGHTENING)
ft·lbf
N·m
Flats
Turns
6
8
2
9
12
2
12
16
2
18
24
2
34
46
2
46
62
1-1/2
75
102
1
90
122
1
105
142
3/4
140
190
3/4
160
217
1/2
Model Year - 2010
1/3
1/3
1/3
1/3
1/3
1/4
1/6
1/6
1/8
1/8
1/12
Advertisement
Table of Contents
