Reliance electric GV3000 Instruction Manual page 79

A C input
diodes, checking, 9 6 to 9 7
disconnect, installing, 5 2 to 5 4
isolation transformer, 5 1
line branch circuit fuses, 3 7 to 3 8, 5 1 to 5 3
ratings, 2 2
wire sizes, 3 5 to 3 6
wiring, 3 5 to 3 7, 4 1 to 4 8, 5 1 to 5 5
voltage transients, avoiding, 5 1
A C output
wiring, 3 5 to 3 7, 4 1 to 4 8, 6 1 to 6 2
Air flow, 3 1, 3 4
Alarms, 9 1
Altitude requirements, 3 1
Ambient conditions, 3 1, A 1
Analog output, 2 9
0 10 VDC (J17), 2 9 to 2 11, 2 13, A 2
4 20 mA (J17), 2 9 to 2 11, 2 13, A 2
wiring, 2 14, 7 1, 7 3 to 7 4, 7 8
Analog input speed reference
input current, wiring, 2 14, 7 1, 7 3 to 7 4, 7 9,
A 2
input voltage, wiring, 2 14, 7 1, 7 3 to 7 4, 7 9,
A 2
0 10 VDC (J4), 2 10 to 2 12, 7 1
4 20 mA (J4), 2 10 to 2 12, 7 1
Area required, 3 2 to 3 4
Audience, intended, 1 2
Block diagram
vector regulation, B 3
volts/hertz regulation, B 2
Board
Bus Clamp, 2 7 to 2 8, 9 11 to 9 12
Capacitor, 2 3 to 2 5, 9 8 to 9 9
Current Feedback, 2 3 to 2 5, 9 8
Gate Driver, 2 5 to 2 8, 9 9 to 9 12
Intelligent Power Module (IPM), 2 7 to 2 8, 9 11
to 9 12
Option, 2 15, 2 16
Power, 2 5, 2 6, 9 9, 9 10
Power Supply, 2 5, 2 6, 9 9, 9 12
Regulator, 2 3 to 2 14, 3 7, 9 8 to 9 10
Thyristor Precharge, 2 8, 9 12
Braking, snubber resistor, 2 9, 2 16, 5 1, A 2
wiring, 2 14, 7 2 to 7 4, 7 14
Bus clamp board, 2 7 to 2 8, 9 11 to 9 12
Downloaded from StockCheck.com
A
B
Index
Capacitor board, 2 3 to 2 5, 9 8 to 9 9
Capacitors, D C bus, 9 1 to 9 5
Carrier frequency, 2 9, A 1
CS3000, see Control and Configuration Software
Closed loop, see Vector Regulation
Communication port (J8), 2 10 to 2 11, 2 15, 3 7,
7 1, 7 7
Communication, network, 2 15, 3 7
Component locations, 2 3 to 2 8
Conduit size, 4 2 to 4 7
Control and Configuration Software, 1 2, 2 16, 3 7,
7 7
Contacting Reliance, 1 2
Contactors, installing output, 6 1
Contacts
Form A, 2 9, 7 15
Form B, 2 9, 7 15
Control source, 7 1, 7 3 to 7 4, 7 7
PC, 3 7, 7 1, 7 7
wiring, 7 3 to 7 4, 7 7
Control, wiring, 2 13, 7 1 to 7 15
Current Feedback board, 2 3 to 2 5, 9 8
Current transformer, 2 7 to 2 8, 9 11 to 9 12
D C bus
input wiring, 3 5 to 3 6, 4 1 to 4 8, 5 3, 5 5
fuse, 2 7 to 2 8, 9 11 to 9 12
terminals, 9 1 to 9 5
verifying capacitor voltage, 9 1 to 9 5
Digital input wiring, 2 14, 7 2 to 7 4, 7 10 to 7 14
8 (remote/local), 7 2 to 7 4, 7 10
7 (ramp1/ramp2), 7 2 to 7 4, 7 11
6 (forward/reverse), 7 2 to 7 4, 7 12
5 (function loss), 7 2 to 7 4, 7 13
4 (run/jog), 7 2 to 7 4, 7 13
3 (reset), 7 2 to 7 4, 7 14
2 (stop), 7 2 to 7 4, 7 14
1 (start), 7 2 to 7 4, 7 14
Digital output wiring, see Status Relays
Dimensions, 3 2 to 3 3
Disconnect, installing A C input, 5 2 to 5 4
Display, see Keypad/Display
Distribution system capacity, A C line maximum, 5 1
Drive,
identifying, 2 1
kits, 2 16
C
D
Index 1