1. Manuals
  2. Brands
  3. Directed Manuals
  4. Automobile Accessories
  5. DS4+
  6. Installation manual

Directed Directechs DS4+ Installation Manual

Hide thumbs Also See for Directechs DS4+:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION GUIDE
TL2
Designed by Installers for Installers
© 2017 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
2017-11-22
DS4+

Advertisement

Table of Contents
loading

Related Manuals for Directed Directechs DS4+

Summary of Contents for Directed Directechs DS4+

  • Page 1 INSTALLATION GUIDE Designed by Installers for Installers © 2017 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.

  • Page 2: Table Of Contents

    Contents Warning! Safety first ........................3 Introduction ............................ 4 Pre-installation and application warnings ..................4 Vehicle application guide ......................5 Wiring connections ......................... 6 Main harness (H1), 12-pin black connector .................. 6 Relay harness (H2), 10-pin white connector .................. 6 Data harness (H3), 8-pin white connector ..................

  • Page 3: Warning! Safety First

    The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation.

  • Page 4: Introduction

    Connection required ONLY if Pit-Stop/Idle mode is desired. Additional parts required (maximum required): Resistor 100Ω Fuse 7.5A Diode 6A 0 x 1A Diodes 0 x Resistor 0 x Fuse 0 x Relay DS4+ TL2 © 2017-11-22 Directed. All rights reserved.

  • Page 5: Vehicle Application Guide

    DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status DS4+ TL2 © 2017-11-22 Directed. All rights reserved.

  • Page 6: Wiring Connections

    (MUX) Analog Input/Output H3/7 Orange/Black Immobilizer Data 2 H3/8 Yellow/Black Immobilizer Data 1 If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. DS4+ TL2 © 2017-11-22 Directed. All rights reserved.

  • Page 7: Analog Input/Output Harness (H4), 22-Pin White Connector

    If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. DS4+ TL2 © 2017-11-22 Directed. All rights reserved.

  • Page 8: Important Oem Remote Starter Information

    4. After programing is successful replace the fuse powering the OEM Remote Starter. Important Module Programming Information During “Module Programming” if the Directed interface detects an OEM Remote Starter it will direct the installer to the “Important OEM Remote Starter Information” section of the guide detailing the next steps.

  • Page 9: Installation (Wiring Diagrams, Fuse Selection & Vehicle Wiring Reference Charts)

    Slide DS4+ to open (-) Push-To-Start: Blue, pin 7 It is important to check that the fuses are positioned correctly. Steering Lock Black ENGINE START connector (black 7-pin connector) STOP 11 10 DS4+ TL2 © 2017-11-22 Directed. All rights reserved.
  • Page 10 Push-to-Start switch. Black Black Data Rear of Main Body ECU. White Blue Data Rear of Main Body ECU. White Parking Lights Rear of Main Body ECU. White Violet Steering Lock Position Connector. Black DS4+ TL2 © 2017-11-22 Directed. All rights reserved.

  • Page 11: Type 2

    (-) Push-To-Start: Blue or Lt. Green, pin 7 Lt. Blue, pin 4 Black ENGINE Slide START connector STOP DS4+ to open 11 10 Steering Lock (black 7-pin connector) It is important to check that the fuses are positioned correctly. DS4+ TL2 © 2017-11-22 Directed. All rights reserved.
  • Page 12 White Lt. Green Push-to-Start switch. Black Green Steering Lock Position Connector. Black Parking Lights Violet Main Body ECU. White Pink Data Main Body ECU. White Lt. Green Data Main Body ECU. White DS4+ TL2 © 2017-11-22 Directed. All rights reserved.
  • Page 13 Data OBDII. White Blue Push-to-Start switch. Black Green Steering Lock Position Connector. Black Parking Lights Yellow Main Body ECU. White Black Data Main Body ECU. White Blue Data Main Body ECU. White DS4+ TL2 © 2017-11-22 Directed. All rights reserved.

  • Page 14: Type 3

    (+) 12V Input: Red: 6 & 12 Black Positioning ENGINE START connector STOP 11 10 (-) Ground: Black: 10 Slide DS4+ to open It is important to check that the fuses are positioned correctly. DS4+ TL2 © 2017-11-22 Directed. All rights reserved.
  • Page 15 HS CAN Low Data OBDII. White White (Plug-in Hybrid) Black Push-to-Start switch. Black Parking Lights Yellow Main Body ECU. White Violet Data Main Body ECU. White Green Data Main Body ECU. White DS4+ TL2 © 2017-11-22 Directed. All rights reserved.
  • Page 16 OBDII. White HS CAN Low White Data OBDII. White Black Push-to-Start switch. Black Parking Lights Yellow Main Body ECU. White Violet Data Main Body ECU. White Green Data Main Body ECU. White DS4+ TL2 © 2017-11-22 Directed. All rights reserved.

  • Page 17: Configuring The System

    DO NOT connect the SmartStart 2-pin power harness when using the DS4+. Power and ground will be provided by the D2D connector on main module. Refer to the SmartStart documentation for further details. DS4+ TL2 © 2017-11-22 Directed. All rights reserved.

  • Page 18: D2D Port Configuration

    By default, the tachometer is preprogrammed for the vehicle. For instructions on how to Initialize tachometer program tach, see page 22. * Your aftermarket remote may differ from the model shown in the illustrations. You have successfully completed the module programming sequence. DS4+ TL2 © 2017-11-22 Directed. All rights reserved.

  • Page 19: Led Diagnostics And Troubleshooting

    The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to MUX not detected. "Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)" on page 9 to Flashes red x 7 check the connections. DS4+ TL2 © 2017-11-22 Directed. All rights reserved.
  • Page 20 The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 Analog error codes Description Troubleshooting DEI feature error. A feature config file mismatch was detected. Please contact Technical Support. Flashes red, green & orange DS4+ TL2 © 2017-11-22 Directed. All rights reserved.

  • Page 21: Soft Reset

    After 3 seconds the LED turns ON solid orange. Keep holding the programming button until & & the LED flashes red, then orange slowly. Solid Hold Flashes Release the programming button. The LED turns ON solid red. & Release Solid DS4+ TL2 © 2017-11-22 Directed. All rights reserved.

  • Page 22: Learning The Tach (Not Needed With Virtual Tach)

    Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature using the DirectLink application for mobile devices to adjust the starter output time in 50mS increments to compensate for such an occurrence. DS4+ TL2 © 2017-11-22 Directed. All rights reserved.

  • Page 23: Limited Lifetime Consumer Warranty

    Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;...

  • Page 24: Quick Reference Guide

    Refer to your authorized installation center for more specific • Aftermarket remote. information. • Directed SmartStart application via your smartphone. Button(s) Actions If applicable, you can also start the engine remotely by pressing the Lock button 3 Press & hold for 1 second to lock.
  • Page 25 The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.

Table of Contents