Directed Directechs DS3+ Installation Manual
2019 audi q8 (smart key)
Hide thumbs
Also See for Directechs DS3+:
- Installation manual (35 pages) ,
- Installation manual (24 pages) ,
- Installation manual (24 pages)
Table of Contents
Advertisement
Quick Links
INSTALLATION GUIDE
DS3+ / DS4+
2019 Audi Q8 (Smart Key). 933.VW08 1.39.195.3
Designed by Installers for Installers
© 2021 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
Advertisement
Table of Contents
Related Manuals for Directed Directechs DS3+
Summary of Contents for Directed Directechs DS3+
- Page 1 2019 Audi Q8 (Smart Key). 933.VW08 1.39.195.3 Designed by Installers for Installers © 2021 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s...
-
Page 2: Table Of Contents
Contents Introduction Vehicle function compatibilities Pre-installation and application warnings Wiring diagram Locating components in the vehicle Immobilizer interface with OEM immobilizer receiver Vehicle connections Connecting the module Important! 8556T Temperature Sensor 8504D Combo Sensor RF Systems When used in conjunction with SmartStart D2D port configuration Manual transmission Module programming... -
Page 3: Introduction
Introduction DS3+ is a complete solution for remote start, security (when security features are enabled) and bypass. This guide provides information on the installation of the module as a digital solution. Please refer to www.directechs.com for more information about which configuration is best for your application. Warning! This module can be configured using the web tool located at www.directechs.com. -
Page 4: Pre-Installation And Application Warnings
Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. Keys T-Harness Keys required required for compatible for operation programming Š... -
Page 5: Wiring Diagram
Wiring diagram Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( HS CAN 1 High: Blue/Green, pin 6 (-) Ground: Brown/Black, pin 4 OBDII Diagnostic Twisted pair Connector (in driver kick, door harness) Refer to the... -
Page 6: Locating Components In The Vehicle
Locating components in the vehicle Optional starter disable connection When using an external relay, use a 1N4002 diode or larger. 1A diode [1N4002+] (+) Ignition (-) Ground When Armed (GWA) Output: Blue/White: 2 Refer to the Vehicle connections section for wire and Starter (conn. -
Page 7: Immobilizer Interface With Oem Immobilizer Receiver
Immobilizer interface For vehicles with Keyless Entry you must remove battery from OEM key (the OEM remote may differ from the models shown in the illustrations). Method 1: Key Wrap for Push-to-Start (PTS) 4-6 loops Remove battery from OEM Remote Control Immobilizer NO Relay 2: Lt. -
Page 8: Vehicle Connections
Vehicle connections The connection information listed below is specific to the 2019 Audi Q8 (Smart Key). Refer to “Pre-installation and application warnings” for a list of important notes. Data harness, 8-pin white connector (H1) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color... - Page 9 Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H2/17 Black/White No Connection No Connection H2/18 Orange/Black No Connection No Connection H2/19 Blue No Connection No Connection H2/20 Green No Connection No Connection H2/21 Gray (-) Hood Switch Input [1] H2/22 Violet/White No Connection...
- Page 10 RF Port harness, 2-pin white connector (H5) Module Conn./Pin Color Description H5/1 RF Loop H5/2 RF Loop D2D harness, 4-pin white (1) and black (2) connectors (H6) Module Conn./Pin Color Description H6/1 Blue (Data) TX H6/2 Black (-) Ground H6/3 Green (Data) RX H6/4...
-
Page 11: Connecting The Module
Configuring the system DS3+ Flashing the module using your computer: 1. Disconnect the main module from any (+) 12V power source, then connect it to your computer using the XKLoader2. 2. Go to www.directechs.com using Internet Explorer; the configuration wizard will be displayed automatically. Follow the instructions in the pop-up window that will be displayed when the module is detected. -
Page 12: Rf Systems
RF Systems An RF System consists of one or multiple remotes, a Control Center (antenna), and an antenna cable – various combinations exist. An RF System allows the vehicle owner to control the system with enhanced range. Two-way models are available. Please follow the instructions included with the kit for appropriate installation and programming information. -
Page 13: Manual Transmission
Manual Transmission IMPORTANT! Directed does not approve nor support installations of manual transmission and remote starts on any electronic vehicles (EV), OEM Remote Start Activation firmware, vehicles with convertibles and/or removable tops, including but not limited to Jeep Wrangler, Honda S2000, Mazda Miata, and other such vehicles. -
Page 14: Module Programming
Module programming Refer to “LED diagnostics and troubleshooting” for more information and for troubleshooting purposes. (For security-only programming, see next section.) Please ensure that the vehicle is in a safe location, and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position. -
Page 15: Module Programming For Security-Only Installations
Module programming for security-only installations Refer to "LED diagnostics and troubleshooting" for more information and for troubleshooting purposes. To connect the module: Please ensure that the vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift lever is in the neutral position. -
Page 16: Led Diagnostics And Troubleshooting
LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module Programming Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black Module has no power. - Page 17 External Module Synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 Active Ground When Running (Status) Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence.
-
Page 18: Soft Reset
Soft reset A module reset will only erase the steps perfomed in “Module Programming”. The firmware and settings flashed to the module will not be affected. Connect all but the If required for your installation, connect all the harnesses to the module, EXCEPT the 12-pin 12-pin harness main power harness. -
Page 19: Learning The Tach (Not Needed With Virtual Tach)
Learning the Tach (not needed with Virtual Tach) Tach comes preprogrammed, therefore learning is not required; however, it can be readjusted with the following operations: 1. Start the vehicle using the key. 2. Within 5 seconds, press and hold the Control Center (antenna), the LED/Valet Pod (standalone switch) or the main module programming button until the LED turns ON solid. -
Page 20: Limited Lifetime Consumer Warranty
Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;... -
Page 21: Quick Reference Guide
• Aftermarket remote. Press the Remote Start button on the transmitter.* • Directed SmartStart application via your smartphone. & The parking lights will flash once to indicate the Parking lights flash x1 If applicable, you can also start the engine remotely by pressing the Lock button 3 Press Remote vehicle is now in Pit Stop Mode. - Page 22 The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.