Table of Contents
Advertisement
3
OSD -
MOTION SETUP
1
MOTION SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
PRESET LOCK
PWR UP ACTION
AUTO FLIP
JOG MAX SPEED
JOG DIRECTION
FRZ IN PRESET
<PARKING ACTION SETUP>
BACK
EXIT
2
PARKING ACTION SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
PARK ENABLE
WAIT TIME
PARK ACTION
BACK
EXIT
OFF
ON
ON
1 40/SEC
NORMAL
OFF
Press Near/Enter Key
OFF
00: 1 0:00
HOME
1
MOTION SETUP
Configures the general functions of pan/tilt motions.
PRESET LOCK
ON / OFF
If motion lock is set to ON, it will be impossible to setup or delete a
preset, scan, pattern, and/or group. It will only be possible to run those
functions. To setup and delete those functions, go to OSD menu.
PWR UP ACTION
ON / OFF / <PWR P>
This functions sets an action for your camera to excecute when it restarts.
- ON: Camera resumes the last action executed before power went
down. Most actions such as preset, pattern, scan, and group resume
for this function, but jog action does not resume with this function.
- OFF: Camera will move to the home position.
- <PWR P>: Camera will move to the set <PWR P> position.
If AUTO CAL is turned ON, PWR UP ACTION should also be set as ON.
If AUTO CAL is set to ON and PWR UP ACTION is set to PWR P, the
camera will most likely cause a malfunction.
If PWR UP ACTION is set as PWR P, FOCUS MODE should be set as
AUTO. If FOCUS MODE is set as SEMIAUTO while PWR UP ACTION is
set to ON, the camera will most likely cause a malfunction.
AUTO FLIP
ON / OFF
When the tilt angle arrives to the top of the tilt orbit (90°), zoom module
module camera continues moving opposite of the tilt direction (180°)
to continue tracing targets. As soon as zoom module camera passes
through the top of tilt direction (90°), images should be reversed
automatically and F appears on the screen. If this function is set to OFF,
tilt movement range is 0° ~ 90°.
JOG MAX SPEED
2/SEC ~ 200/SEC
Sets maximum jog speed. Jog speed is inversely proportional to zoom
magnification. As zoom magnification goes up, pan/tilt speed goes down.
JOG DIRECTION
INVERSE / NORMAL
If you set this to NORMAL, the view on the screen is moving in the same
direction with jog tilting. If INVERSE is selected, the view on the screen
is moving in the reverse direction.
ON / OFF
FRZ IN PRESET
When preset movement begins, the camera captures the image of the
beginning point. Camera will display the captured image during the
preset movement and will not display the images the camera receives
during the movement. As soon as the camera stops at the preset end
point, the camera begins to display the live images it receives at the
end point.
<PARKING ACTION SETUP>
Opens to PARKING ACTION SETUP screen.
2
PARKING ACTION SETUP
If PARK ENABLE is set to ON, camera runs assigned function
automatically if there is no PTZ command during assigned
WAIT TIME.
PARK ENABLE
ON / OFF
WAIT TIME
00:00:05 ~ 04:00:00
The time is displayed in "hh:mm:ss" format, and the time can be
changed by 1 second unit.
1. To place the cursor on the time marked as shown below, press Near
key.
00:10:00
2. Move joystick Left/Right to adjust hours, minutes, and seconds.
3. Move joystick Up/Down to select the digit.
4. Press Near key to save the current setting.
HOME / PRESET 1~128 / SCAN 1~8 /
PARKING ACTION
PATTERN 1~4 / GROUP 1~8
Ex) If HOME is selected for park action, camera will move to home
position when there is no PTZ command during the assigned WAIT TIME.
Advertisement
Table of Contents
