Table of Contents
Advertisement
Quick Links
ACMJ Series
Access Power Controllers
with Power Supplies
Installation Guide
Models Include:
AL400ULACMJ
- 12VDC @ 4A
or 24VDC @ 3A.
- Fused Outputs
AL600ULACMJ
- 12VDC or 24VDC @ 6A.
- Fused Outputs
Rev. 052819
AL1012ULACMJ
- 12VDC @ 10A.
- Fused Outputs
AL1024ULACMJ
- 24VDC @ 10A.
- Fused Outputs
More than just power.
TM
Advertisement
Table of Contents
Related Manuals for Altronix ACMJ Series
Summary of Contents for Altronix ACMJ Series
- Page 1 ACMJ Series Access Power Controllers with Power Supplies Installation Guide Models Include: AL400ULACMJ AL1012ULACMJ - 12VDC @ 4A - 12VDC @ 10A. or 24VDC @ 3A. - Fused Outputs - Fused Outputs AL600ULACMJ AL1024ULACMJ - 12VDC or 24VDC @ 6A.
-
Page 2: Output Voltage And Stand-By Specification Charts
Overview: Altronix ACMJ Series units distribute and switch power to access control systems and accessories. They convert a 115VAC 60Hz input into eight (8) independently controlled 12VDC or 24VDC fuse protected outputs. These power outputs can be converted to dry form “C” contacts. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. -
Page 3: Specifications
Input: Outputs (cont’d): • Power input 115VAC, 60Hz • Alarm output relay indicates that FACP input is (see ACMJ Series Power Supply Configuration triggered (form “C” contact rated @ 1A 28VDC, Reference Chart, pg. 2). not evaluated by UL). • ACM8 Power Input Options: •... - Page 4 When using DC power supplies polarity must be observed. When using AC power supplies polarity need not be observed (Fig. 1d, pg. 6). Note: For UL compliance the additional power supply must be power-limited, UL Listed for Access Control Systems and accessories. - 4 - ACMJ Series...
-
Page 5: Maintenance
FACP output circuit (Fig. 4 through 8, pgs. 8-9). FACP INTERFACE Form “C” relay contact rated @ 1A 28VDC for alarm reporting. NC, C, NO (This output has not been evaluated by UL). ACMJ Series - 5 -... -
Page 6: Typical Application Diagram
Battery Status Normal operating condition. Battery fail/low battery. ACM8 Access Power Controller LED 1 - LED 8 (Red) Output relay(s) energized. Output relay(s) de-energized. Trg (Green) FACP input triggered (alarm condition). FACP normal (non-alarm condition). - 6 - ACMJ Series... - Page 7 CAUTION: Optional rechargeable stand-by batteries must match the power supply output voltage setting. Keep power-limited wiring separate from non power-limited. Use minimum 0.25" spacing. *When Class 2 rating is required order model numbers: AL400ULACMCBJ, AL600ULACMCBJ, AL1012ULACMCBJ and AL1024ULACMCBJ ACMJ Series - 7 -...
-
Page 8: Hookup Diagrams
Fig. 4 Polarity reversal input from FACP signaling circuit output (polarity is referenced in alarm condition): JUMPER FACP FACP OUTPUT EOL FROM FACP OUTPUT CIRCUIT Fig. 5 Normally Open: Non-Latching FACP trigger input: FACP N.O. TRIGGER INPUT - 8 - ACMJ Series... - Page 9 Fig. 7 Normally Closed: Non-Latching FACP trigger input: FACP N.C. DRY TRIGGER INPUT JUMPER Fig. 8 Normally Closed: Latching FACP trigger input with reset: (This output has not been evaluated by UL) FACP N.C. RESET SWITCH N.C. TRIGGER JUMPER INPUT ACMJ Series - 9 -...
- Page 10 36AH. You have to reduce either stand-by current consumption or stand-by time in order to comply with requirement. To determine actual battery size please round line [J] to the nearest larger standard battery size. - 10 - ACMJ Series...
- Page 11 Notes: ACMJ Series - 11 -...
-
Page 12: Enclosure Dimensions
14.5” (368.3mm) Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty | Made in U.S.A. MEMBER IIACMJ Series E28S...