Technogym ACTIVE Wellness TV RUN EXCITE Machine Configuration page 19

ACTIVE WTV: Machine configuration
Press the ADDRESS key, insert the desired address and press ENTER to confirm and display the
parameter value. Press BACK key to back forward.
Press the VALUE key, insert the correct value and press ENTER to confirm the new parameter
value. Press BACK key to back forward.
Although the changes made to the parameters come into effect immediately, they are not
automatically stored in permanent memory; this requires a specific write operation
effected using the command C-0: at address 800 write the value "1".
To return to the upper menu level press CLEAR for a few seconds.
Par. AddressDescription
PID mode (700/900)
A-0 1200
PID mode (500)
A-1 1201PID ref sel
A-2 1202PID fbk sel
A-3 1203PID digital ref
A-4 1204PID activat mode
A-5 1205PID-Encoder sync
A-6 1206PID err sign rev
A-7 1207PID Integ init en
A-8 1208PID update time
A-50 1209PID Prop gain 1
A-51 1210PID Int tconst 1
A-52 1211PID Deriv gain 1
A-53 1212PID Prop gain 2
A-54 1213PID Int tconst 2
A-55 1214PID Deriv gain 2
A-56 1215PID high limit
A-57 1216PID low limit
A-58 1217PID max pos err
Par. Address Description
C-0 800 Save parameters
C-1 801 Recall param
C-2 802 Load default
C-20 803 Alarm clear
C-40 804 Recall key prog
Par. Address Description
D-0 1 Output frequency
D-1 2 Frequency ref
D-2 3 Output current
D-3 4 Output voltage
D-4 5 DC link voltage
D-5 6 Power factor
D-6 7 Power [kW]
D-7 8 Output speed
MENU –A–
Value Par. AddressDescription
1 A-59 1218PID min neg err
0 A-100 1219Set Linear speed
5 A-101 1220Set Acc Dec
4 A-102 1221Set Incline ref
0 A-105 1222Def Linear speed
0 A-106 1223Def Acc Dec
1 A-107 1224Def Incline ref
0 A-110 1225Pulley Ratio
0 A-111 1226Roller Diameter
0
A-115 1227
7
150 A-116 1228Fan command dly
0
A-117 1229ACMot EncToller
0
9999 A-118 1230Check RunnerBand
0 A-119 1231Check RunnerSpd
80 A-120 1232Curr clamp thr
-80 A-121 1233Check RunnerDly
50
MENU –C–
Value Par. Address Description
0 C-41 805 Save pars to key
0 C-100 806 Measure stator R
0 C-200 807 Reset AC Flag
0 C-201 808 Reset DC Flag
0
MENU –D–
Value Par. Address Description
0 D-200 26 An in 1 cnf mon
0 D-201 27 An in 1 monitor
0 D-202 28 An in 1 term mon
0 D-210 29 An in 2 cnf mon
400 D-211 30 An in 2 monitor
100 D-212 31 An in 2 term mon
0 D-220 32 An in 3 cnf mon
0 D-221 33 An in 3 monitor
DCMot EncTimeout
(AT driver SW ≥ 2.07)
Value
50
0
100
0
8
100
0
200
91
15
3
50
0(OFF)
10
50
200
60
Value
0
0
0
0
Value
0
0
0
0
0
0
0
0
Page 15