Advertisement
Quick Links
Advertisement
Related Manuals for RELM RPV599APIus
Summary of Contents for RELM RPV599APIus
-
Page 2: Table Of Contents
TABLE OF CONTENTS GENERAL lNFORMATlON ....................1 . 1 1 . 2 Description ......................1.3 Accessories ......................1.4 License Requirements ..................1.5 Technical Assistance ................... 1.7 LCD lcxrns ......................FIELD (KEYPAD) PiWGRAMMlNG ..................Programming Modes ................. -
Page 3: General Lnformatlon
RELM Wireless dealer for complete information. This equipment must be licensed by the Federal Communications Commission (FCC) before it may be used. Your RELM Wireless dealer can assist you in filing the appropriate application for the FCC, will program each radio with your... - Page 4 Controls and Indicators (1) ANTENNA (2) CHANNEL SELECTOR KNOB Used to select channel and squelch level. In addition, it can be programmed by the or to select CTCSS frequency. dealer to delete undesired channels from scan list (3) LED INDtCATOR (4) ON-OFF/VOLUME KNOB Rotate the volume control knob clockwise to turn the unit ‘on”...
- Page 5 1.7 LCD kons Channel Number- Displays channel number. Factory default channel frequency. Channel Lab& Displays characters of the channel label. Up to 16 alphanumeric characters can be programmed. Any label over 8 charactars will scroll across the display. RELM Communhtions Page 3...
- Page 6 RELM Communications Page 4...
- Page 7 21.1 P~ramming Modes Using the unit’s keypad, soft keys, and control knobs, the unit can be placed into one of several diierertt programming modes. It is important to not& that only RELM authorized dealers with qualified technicians allowed to operate the RPV99Plus series radios in the mode and to change any programming content.
- Page 8 “on”. After 2 seconds the radio enters the dealer mode and “SEL” appears on the display. While in dealer mode, press the respective soft function key for the mode to be programmed. See Table 2.2. RELM Communications Page 6...
-
Page 9: Dealer Mode Pragramming
2.1.3.1 Global Settings To place the unit into the “Dealer Mode” for adiing tha global settings, do the following: 1. While pressing and hilding the [lAMPI and [ 0] buttons, switch the power ‘on“. After 2 seconds the radio enters the dealer moda and display. - Page 10 SCAN TO ‘Time Operated’ SCAN. Disable DIAL OFF Disables the fDlAL1 kev. the same as the receive frequency and the receive frequency becomes the same as the transmit Disable OFF 1 Disables the [LO] button so the user cannot select the low power mode.
- Page 11 LBB 500 Conditions: 1. The priority feature is enabled. 2. The Scan feature is enabled. 3. The radio is in the scan mode. 4. The radio stops on an active channel that is not the priority channel. 5. A signal is detected on the priority channel, but the signaling squelch (CTCSS, CDCSS, ~-TOM?, DTMF) is not the same as the priority channel.
- Page 12 Disabled. Prohibii the user to add or delete Disable channels to or from the list of channels to be scanned. from the list of channels to be scanned. Disable MODE OFF Prohibii Dealer and Test modes Page 10 RELM Communications...
-
Page 13: Dtmf Settings
DTMF Settings To place the unit into the ‘Dealer Mode’ for ediing the DTMF settings, do the following: 1. While pressing and holding the (LAMP] and [O] buttons, switch the power “on”. After 2 seconds the radio enters the dealer mode and “SEL” appears on the display. 2 . - Page 14 DTMF HOLD the last number on the DTMF key is TIME manually selected, but only if the PTT button is released after the last number. Does not allow Auto ID numbers to be STORE 8 SEND RELM Communications Page 12...
- Page 15 Is - 15s the period of time before the squelch is SART 10 reset to the ready state of decoding SART 15 another DTMF signal. met to 7XW; and the 2-Tone settings will be reset to V”. RELM Communications Page 13...
- Page 16 0, the receiving radio will not transpond. If any of the functions in Table 2.3 and Table 2.4 are set to “Off”, the related setting shown in can be set, but tha setting will not be recognized. RELM Communications Page 14...
- Page 17 The current function option will not be stored if it was changed. After the complete option list has been cycled through, “End” will appear on the display. To exit dealer mode, cycle the power “off’ and then back ‘on”. Page 15 RELM Communications...
- Page 18 Displa y Frequency Display Mode Scan Add/Del Kev Lock . ._ VQT Variable C . K3 SQL The function key is disabled. No Function K4 OFF Scan K4 SCAN The function selected will be assigned to this RELM Communications Page 16...
-
Page 19: Channel Settings
unit into the “Dealer McxW’ for editing the channel settings, do the following: 1. while pressing and holding the [LAMP] and [O] buttons, switch the power “on’. After 2 seconds the radio enters the dealer mode and %EL” appears on the display. 2. - Page 20 6.25Kl-l~; if there isn’t a decimal point shown next to the last digit of the frequency, then the increment is 2.5KHz. Pressing the [a] key will toggle the increment size between 2.5kl-l~ and 6.25Kl-l~. RELM Communications...
- Page 21 5 watts to 1 watt or from 1 TXPWR L Low power is 1 watt. The [Lo] button will not toggle the channel to high power. Always set to low power. WIDE Receiver bandwk#h is +I-25KHz and transmit deviation is less than +/SKHz. Page 19 RELM Communkations...
- Page 22 Table 2.11 for all the possible characters and character assignment. Table 2.7 - Dealer Mode Channel Settings Any tone frequency between 67.0 Hz and 250.3 Hz can be programmed into the RP599APlus Frequencies shown in table 2.8. Table 2.8 - CTCSS Frequencies Also, the RELM Communications Page 20...
- Page 23 Any CDCSS coda between 000 and 777 can be programmed into the RP599APlus Series radios. However, it is recommended to use the standard TIA/ElA-603-A CDCSS Codes shown in tab#e 2.9. Table 2.9 - Standard TWElA493-A CDCSS Codes A tone fmm 260 Hz to 3500 Hz in 1 Hz inctemants can be used for P-Tone signaling. Only the frequencies in the lTS table can be selected when programming through the front keypad.
- Page 24 Table 2.11 shows 8ll possible char8cters and key assignment to the characters that can be used for entering the channel i 7 i ts the cursor to the next character location, -+ Used to move the cursor back and forth, +-+ Table 2.111 Lat RELM Communications...
- Page 25 Cloning allows the memory contents of one unit (source) to be transferred to another unit (target). There are twu mathods that can be usad for cloning tha RPV5gg sarias radii. Wired - Cloning using tha CCRP cloning cable. 2. Connect each end of tha CCRP cable into the respective micmphone jacks of the radii. 3.
-
Page 26: Cloning
3. Pressthc A freqw b to ac&rst the freqwwy to the desii to receive data on. Note: Pressing the [LAMP] in 1 MHz steps. Source Display 4. While pn power UonD. After 2 seconds the radio enters the desk mode and “SEL” appears on the display. 5.