Cvt Cover Removal And Installation - BRP Can-Am COMMANDER 2021 Series Operator's Manual

S S p p a a r r k k P P l l u u g g G G a a p p
0.8 to 0.9 mm.031 to .035 in
3. Coat spark plug threads with the
following anti-seize lubricant.
C C o o o o p p e e r r - - b b a a s s e e d d a a n n t t i i - - s s e e i i z z e e
l l u u b b r r i i c c a a n n t t
4. Screw spark plug into cylinder
heads by hand and tighten with a
torque wrench
socket.
N N O O T T I I C C E E
D D o o n n o o t t o o v v e e r r t t i i g g h h t t e e n n s s p p a a r r k k p p l l u u g g s s , ,
e e n n g g i i n n e e d d a a m m a a g g e e c c a a n n o o c c c c u u r r . .
T T i i g g h h t t e e n n i i n n g g T T o o r r q q u u e e
Spark plug
C C V V T T C C o o v v e e r r
For a better understanding, some il-
lustrations are taken with engine out
of vehicle. To perform the following in-
structions, it is not necessary to re-
move engine.
W W A A R R N N I I N N G G
N N e e v v e e r r t t o o u u c c h h C C V V T T w w h h i i l l e e e e n n g g i i n n e e i i s s
r r u u n n n n i i n n g g . .
N N e e v v e e r r d d r r i i v v e e v v e e h h i i c c l l e e w w h h e e n n C C V V T T
c c o o v v e e r r i i s s r r e e m m o o v v e e d d . .
C C A A U U T T I I O O N N
E E n n g g i i n n e e m m u u s s t t b b e e c c o o o o l l b b e e f f o o r r e e c c o o v v e e r r
i i s s r r e e m m o o v v e e d d . .
N N O O T T I I C C E E
T T h h i i s s C C V V T T i i s s l l u u b b r r i i c c a a t t i i o o n n f f r r e e e e . .
N N e e v v e e r r l l u u b b r r i i c c a a t t e e a a n n y y c c o o m m p p o o n n e e n n t t s s
e e x x c c e e p p t t d d r r i i v v e e p p u u l l l l e e y y b b e e a a r r i i n n g g . .
and a proper
11 Nm (97
lbf-in)
MAINTENANCE PROCEDURES
A A c c c c e e s s s s i i n n g g t t h h e e C C V V T T C C o o v v e e r r
The CVT cover is accessible by the
rear LH wheel well.
R R e e m m o o v v i i n n g g t t h h e e C C V V T T C C o o v v e e r r
1. Place the vehicle on a level
surface.
2. Manually, remove all CVT cover
retaining screws.
N N O O T T I I C C E E
D D o o n n o o t t u u s s e e a a n n i i m m p p a a c c t t t t o o o o l l t t o o r r e e - -
m m o o v v e e C C V V T T c c o o v v e e r r s s c c r r e e w w s s . .
N N O O T T E E : :
Remove the center top screw last to
support the cover during removal.
3. Remove the CVT cover and its
gasket.
1. CVT cover
2. CVT cover screws
I I n n s s t t a a l l l l i i n n g g t t h h e e C C V V T T C C o o v v e e r r
1. Install the center top screw of first.
2. Tighten the CVT cover screws as
per following sequence.
135