Advertisement
Quick Links
EPILOG LASER
16371 Table Mountain Parkway
Golden, Colorado 80403
Phone 303-215-9171
FAX 303-277-9669
www.epiloglaser.com
Epilog Laser Tube Upgrade
Requirements:
Tools:
• Phillips Head Screwdriver
• Set of SAE (US Sized) Allen Keys
• Locking Pliers
• Nut Driver / Wrench (5/16")
Parts:
• Epilog Replacement Laser Tube
• Adapter Bracket (MT266)
• Fans (optional)
• PSU Bracket (optional)
• Rear Panel (optional)
Overview:
This document details the process to upgrade your laser with an Epilog Laser
Tube.
Epilog Laser Tube Upgrade
Mini / Helix
Revision Date: 9/27/2013
For the Epilog Mini / Helix
9/27/20 13
pg. 1 of 17
Advertisement
Related Manuals for Epilog Laser Mini
Summary of Contents for Epilog Laser Mini
- Page 1 • Adapter Bracket (MT266) • Fans (optional) • PSU Bracket (optional) • Rear Panel (optional) Overview: This document details the process to upgrade your laser with an Epilog Laser Tube. Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013...
- Page 2 Disconnect the Red Dot Pointer which is located on the right side of the laser tube. Follow the thin Red and White wires to the Black Connector. Unplug the connector. Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013...
- Page 3 Disconnect the Grey Data Cable from the Left side of the laser tube. Step 4: Disconnect the Red and Black Power Harness. Follow the power Wires to the White Connector and unplug the connector. Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013 pg. 3 of 17...
- Page 4 CAUTION: The laser tube can weigh between 10 and 20 lbs. (4.5 to 9 kg). Please take proper precautions when lifting heavy objects. Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013 pg. 4 of 17...
- Page 5 Step 2: Locate the left hand spacing standoff. Using a pair of Locking Pliers, break the standoff away from the body of the engraver. You will not damage the Engraver. Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013...
- Page 6 Step 5: Align the two screw holes on the right hand side of the adapter bracket, with the screw holes on the engraver. Fasten with the provided screws. Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013 pg. 6 of 17...
- Page 7 Procedure C: Installing the new fans. This procedure is for the Mini 24 and Helix machines only. If you currently have 4 fans but space for 6, please follow this procedure. If you currently have 6 fans or if you own a Mini 18 you can skip this procedure.
- Page 8 Remove the fan tray by locating and removing the nuts on the left and right sides of the tray. Step 5: Insert the new fan tray into the engraver and fasten with the nuts. Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013 pg. 8 of 17...
- Page 9 Step 5: Connect the fan Wire Harness. And fasten with holder. Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013 pg. 9 of 17...
- Page 10 PSU. Do not touch Electrical Contacts, Leads, or Damaged Wires with your bare hands while performing this procedure. Do not attempt to open the PSU’s housing. Electrical charge may still be present in the PSU even after it has been disconnected. Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013...
- Page 11 Step 2: Disconnect the PSU from the Power Receptacle. Follow the Green, White and Black wires until you reach a white connector. Disconnect the white connector. Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013 pg. 11 of 17...
- Page 12 Place the PSU on a flat work area with the Mounting Bracket facing up. Orient the PSU so that the thumb screws are on the side closest to you. Remove the four (4) mounting screws and discard the bracket. Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013...
- Page 13 Place the new bracket (MT525) on the top of the PSU with the thumb screws toward yourself. Align the holes on the bracket with the holes on the PSU and fasten them with the mounting screws. Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013...
- Page 14 Reconnect the Red and Black wires as well as the Green, White and Black wires. If your engraver has more than one PSU, than repeat this procedure for the second supply as well. Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013...
- Page 15 Hang the laser tube on the shoulder screws. Step 2: Slide the laser tube to the left. The entire unit will slide up to a half an inch (12mm). Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013 pg. 15 of 17...
- Page 16 If you completed Procedure D (Installing the new PSU Bracket), you will have been provided with a new rear panel to accommodate the new orientation of the PSU. Please use the new rear panel. Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013 pg. 16 of 17...
- Page 17 You should now be finished installing the Laser Tube Upgrade. Please be sure to align the laser before use. If you require alignment instructions or encounter any problems please contact Epilog Tech Support at (303) 215-9171. Epilog Laser Tube Upgrade Mini / Helix Revision Date: 9/27/2013...