Advertisement
Quick Links
Connect 2.0
Shelter, wiring guide for 8ft solar powered unit
Installation Guide
Order of operations:
1.
Anchor kit installation
2.
Frame assembly
3.
Roof assembly
4.
Wall glass assembly
5.
Wiring connections
Tools Required
• wiring tools
• 3/32" hex key
• 3/16" hex key
• 5/16" Socket wrench
• Flat head screwdriver or ¼" socket wrench
Included components:
• Uplights, with wiring harnesses, pre‐installed in front horizontal beam
• Down lights, with wiring harness and connectors, one per rafter
• Wayfinding lights, with wiring harness, two per unit
• Glass solar panel with brackets and attaching hardware (instructions
separate for roof panel)
• 16 batteries with wiring harnesses
ASSEMBLE WITH CARE! Pangard II Polyester Powdercoat is a strong, long‐lasting finish. To
protect this finish during assembly, place unwrapped powdercoated parts on packaging foam or
other non‐marring surface. Do not place or slide powdercoated parts on concrete or other hard
or textured surface – this will damage the finish causing rust to occur. Use touch‐up paint on any
gouges in the finish caused by assembly tools.
DRIVER PLATE,
BATTERY INSTALL
LOCATION
UPLIGHTS,
PRE‐INSTALLED
DOWNLIGHT,
LOCATION FOR
CENTER SUB‐
HARNESS
BATTERY
INSTALL
LOCATION,
REAR
HORIZONTAL
FRONT OF
SHELTER
Fig. 1 – lighting component locations 8ft shelter
Date: February 14, 2019
www.landscapeforms.com
Ph: 800.521.2546
DOWNLIGHT
RIGHT
FRONT
POST
WAYFINDING
LIGHTS
RIGHT
REAR
POST
Page 1 of 6
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Landscape Forms Connect 2.0
Summary of Contents for Landscape Forms Connect 2.0
- Page 1 Connect 2.0 Shelter, wiring guide for 8ft solar powered unit Date: February 14, 2019 Installation Guide www.landscapeforms.com Ph: 800.521.2546 Order of operations: ASSEMBLE WITH CARE! Pangard II Polyester Powdercoat is a strong, long‐lasting finish. To Anchor kit installation protect this finish during assembly, place unwrapped powdercoated parts on packaging foam or other non‐marring surface. Do not place or slide powdercoated parts on concrete or other hard Frame assembly or textured surface – this will damage the finish causing rust to occur. Use touch‐up paint on any Roof assembly gouges in the finish caused by assembly tools. Wall glass assembly Wiring connections DRIVER PLATE, Tools Required BATTERY INSTALL ...
-
Page 2: Installation
Connect 2.0 Shelter, wiring guide for 8ft solar powered unit Date: February 14, 2019 Installation Guide www.landscapeforms.com Ph: 800.521.2546 INSTALLATION: Unused grommets on rear horizontal beam can be sealed with clear or black Order of installation: Install batteries. 8ft shelter will house 8 batteries in the front silicone (supplied by others). horizontal beam and 8 batteries in the rear horizontal beam. They will connect together Install left and right side rafter skins, with the sharper angle of the skin toward the with a center sub‐harness. Install downlights. Install wayfinding lights. Connect wiring front of the rafter. See Fig. 10. Rafter skins have a boss on the bottom flange that harnesses to driver. Install fuse. Run test of lights. hooks into the downlight, see Fig. 10. Hook the bottom of the skin into position and Remove access cover in horizontal beam near rear left post. Ensure Velcro strip is then rotate the top of skin up to the rafter beam. Using a 3/16” hex key, install (2) installed on rear horizontal beam. Secure one end of long Velcro harness to the top ¼‐20 x ¾” socket head cap screws, located in hardware pack #62599. Tighten until half of the strip mounted in the horizontal beam. Connect (‐) lead of the battery gap between light and rafter skin is gone and rafter skin does not rattle. Do not harness, labeled “BACK HARNESS”, to the first battery (‐). Install short jumper overtighten screws. harness to the positive pole of the battery as shown in Fig. 2. Attach the other end of Wayfinding lights: Run wiring harness up through front vertical post. On the front the jumper harness to the second battery. Install the second battery. Repeat this ... - Page 3 Connect 2.0 Shelter, wiring guide for 8ft solar powered unit Date: February 14, 2019 Installation Guide www.landscapeforms.com Ph: 800.521.2546 WIRING HARNESS LEAD – WIRING HARNESS LEAD – END WITHOUT FUSE END WITHOUT FUSE BATTERY BATTERY FACTORY‐INSTALLED VELCRO STRIP FACTORY‐INSTALLED VELCRO STRIP VELCRO HARNESS VELCRO HARNESS Fig. 2 – beginning of battery install in rear horizontal Fig. 3 – beginning of battery install in front horizontal FRONT REAR TO FACTORY‐ SUB‐HARNESS CENTER ...
- Page 4 Connect 2.0 Shelter, wiring guide for 8ft solar powered unit Date: February 14, 2019 Installation Guide www.landscapeforms.com Ph: 800.521.2546 8 BATTERIES FRONT GROMMET IN FRONT SUB‐HARNESS HORIZONTAL WITH FUSE CONNECT TO FRONT FRONT HARNESS WIRING LONG HARNESS VELCRO QUICK STRAP DISCONNECT CENTER SUBHARNESS (RAFTERS NOT BACK WIRING SHOWN) HARNESS END...
- Page 5 Connect 2.0 Shelter, wiring guide for 8ft solar powered unit Date: February 14, 2019 Installation Guide www.landscapeforms.com Ph: 800.521.2546 RAFTER (2) ¼‐20 x ½ SOCKET HEAD CAP SCREW WIRING HARNESS FOR WAYFINDING FRONT LIGHT HORIZONTAL BEAM COVER PLATE GROMMET ATTACHMENT POINT (3 PER SIDE) Fig. 12 – Install wayfinding QUICK WAYFINDING DOWNLIGHT light cover plate...
- Page 6 Connect 2.0 Shelter, wiring guide for 8ft solar powered unit Date: February 14, 2019 Installation Guide www.landscapeforms.com Ph: 800.521.2546 FUSE LOCATION MORNINGSTAR UNIT Fig. 14 – solar wiring connections (2) ¼‐20 x ½ SOCKET HEAD CAP SCREWS Fig. 13 – Install driver plate assembly, front right access hole Fig. 15 – solar wiring diagram Page 6 of 6...
Need help?
Do you have a question about the Connect 2.0 and is the answer not in the manual?
Questions and answers