Product Specifications; Technical Data - F.F. Group JS 710 PRO Original Instructions Manual

Hide thumbs

Table Of Contents

Table of Contents

Available languages

| English

Pay attention that the base plate rests securely on

the material while sawing. A jammed saw blade can

break or lead to kickback.

When the cut is completed, switch off the machine

and then pull the saw blade out of the cut only after it

has come to a standstill. In this manner you can avoid

kickback and can place down the machine securely.

Use only undamaged saw blades that are in perfect

condition. Bent or dull saw blades can break, nega-

tively influence the cut, or lead to kickback.

Do not brake the saw blade to a stop by applying side

pressure after switching off. The saw blade can be

damaged, break or cause kickback.

Use suitable detectors to find hidden utility lines or

call the local utility company for assistance (contact

with electric lines can lead to fire or electrical shock;

damaging a gas line can result in an explosion; pene-

trating a water pipe will cause property damage or an

electrical shock).

Secure the workpiece a workpiece clamped with

clamping devices or in a vice is held more securely

than by hand.

Always wait until the machine has come to a com-

plete stop before placing it down. The tool insert can

jam and lead to loss of control over the power tool.

Before any work on the machine itself, pull the mains

plug.

Check the tight seating of the saw blade. A loose saw

blade can fall out and lead to injuries.

The saw blade should not be longer than required for

the intended cut. Use a narrow saw blade when saw-

ing tight curves.

Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful

to one's health and cause allergic reactions, lead to re-

spiratory infections and/or cancer. Materials containing

asbestos may only be worked by specialists.

As far as possible, use a dust extraction system

suitable for the material.

Provide for good ventilation of the working place.

It is recommended to wear a P2 filter-class respira-

tor.

The restarting protection prevents uncontrolled

starting of the machine after a power failure. To re-

start the machine, set the On/Off switch to the off

position, and then switch the power tool on again.

The contact protector attached to the casing (09)

prevents accidental touching of the saw blade during

the working procedure and may not be removed.

Before sawing in wood, particle boards, building ma-

terials etc., check for foreign objects, such as nails,

screws, etc. and remove them as required.

Plunge cuts may only be applied to soft materials,

such as wood, gypsum board, etc. For plunge cuts,

use only short saw blades.

Adapt the settings of your power tool to the respec-

tive application. For example, reduce the stroke rate

and orbital action when cutting metal or for tight

curved cuts.

CONNECTION TO THE POWER SUPPLY

Make sure the power supply information on the ma-

chine's rating plate are compatible with the power

supply you intend to connect it to.

This appliance is Class II* and is designed for connec-

tion to a power supply matching that detailed on the

rating label and compatible with the plug fitted. If an

extension lead is required, use an approved and com-

patible lead rated for this appliance. Follow all the

instruction supplied with the extension lead.

*Double insulated

: This product requires no earth

connection as supplementary insulation is applied

to the basic insulation to protect against electric

shock in the event of failure of the basic insulation.

GUIDELINES FOR USING EXTENSION CORDS

Make sure your extension cord is in good condition.

When using an extension cord, be sure to use one

heavy enough to carry the current your product will

draw. An undersized cord will cause a drop in line volt-

age resulting in loss of power and overheating.

Always replace a damaged extension cord or have it

repaired by a qualified person before using it.

Protect your extension cords from sharp objects, ex-

cessive heat and damp/wet areas.

Use a separate electrical circuit for your tools. This

circuit should be protected with the appropriate

time-delayed fuse. Before connecting the motor to

the power line, make sure the switch is in the OFF po-

sition and the electric voltage is rated the same as the

voltage stamped on the motor nameplate. Running

at a lower voltage will damage the motor.