"V 44" or higher. You can find the current op- erating software for the control unit and the cassette, the software "BE-Flash" and the current assembly instructions on the website "www.gss.de". The cassette is designed for use in head-end stations of the standard line.
• Align the cassette and apply slight pressure to connect it to the connections of the board and the HF bus bar. • Fasten the cassette with the screws 0° ACHTUNG! Vor dem Kassettenwechsel MESSAUSGANG unbedingt denNetzstecker ziehen. –20 dBµV CAUTION! AUSGANG Before changing cassettes remove max. 106 dBµV mains plug. Grundig SAT Systems - 6 - HRC 300 AV...
Tighten the nuts of the cable terminals until the teeth on the lock washers put un- der have penetrated the exterior coating and a good connection is made between the housing / 19" cabinet and cable terminals. - 7 - HRC 300 AV...
"RS 232" using a PC or notebook and the software "BE-Flash". You can find the current operating software on the website "www.gss.de". o n n e C t i n g t h e C a s s e t t e • Connect the peripheral devices to the cinch input sockets...
The key pad on the head-end station is used to scroll through the menus: scrolls forward through the menus. select parameters in the menus. set values, initiate actions. selects sub-menus. scrolls backward through the menus. saves all entries. - 9 - HRC 300 AV...
• Connect the test receiver to the HF output or the test output of the head-end station. • Set the output channels / output frequencies of the cassette (page 16) and 16) and ) and adjust the test receiver to the respective channel / frequency. • Switch on the modulator if necessary (page 14). • Measure the output levels of the channel strips and adjust them to a uniform output level (page 17). - 10 - HRC 300 AV...
—> The display shows e.g. the menu "Box 1 3 AV": "Box 1" stands for slot 1 "3AV" type of cassette "V 2" software version of the cassette • Press the button. - 12 - HRC 300 AV...
— > If the channel strip (modulator) is switched off, "off" is displayed instead of the channel or the frequency set. • Press the button. —> The "HF output level" / "Switching the modulator off / on" – "MODULATOR Level" menu is activated. - 13 - HRC 300 AV...
• Place the cursor under "on" or "off" using the buttons. • Press to switch the modulator of the channel strip "off" or "on". —> In position "off" the "Level" menu item is inactive. - 14 - HRC 300 AV...
• Press to select the TV standard of the output signal ("PAL B/G" / "PAL I"). • Press the button. —> The "Setting the output channel" or "Setting the output frequency" – "OUTPUT" menu is activated. - 15 - HRC 300 AV...
—> The settings are saved. —> You return to the "Selecting the cassette" menu (page 12). —> By pressing the button, you will be returned to the menu item "Selecting the channel strip" without saving the programmed data (page 13). - 17 - HRC 300 AV...
Please regard the assembly instructions of the respective head-end station. —> In order to prevent interference within the head-end station and the cable system, the output levels of the digital cassettes must be set lower by 8 dB compared to analogue cassettes. • Mount the front cover (s. assembly instructions of the head-end station). - 18 - HRC 300 AV...
551.25 C 45 663.25 C 59 775.25 C 32 559.25 C 46 671.25 C 60 783.25 C 33 567.25 C 47 679.25 C 61 791.25 C 34 575.25 C 48 687.25 C 62 799.25 - 19 - HRC 300 AV...
Page 20
Declaration of CE conformity - 20 - HRC 300 AV...