Setting the UDP port ..............27 Selecting the input data stream ............27 Setting the LNB oscillator frequency ..........28 Setting the input symbol rate ............28 Setting the DVB mode ..............28 Setting the input frequency ............29 - 2 - HDTV 1000 S...
Page 3
Displaying the output data rate............39 Factory reset ................39 Saving settings ................40 Operation with a CA module ............41 Setting the PID monitoring ............41 Configuring the CA module .............41 Descrambling services .............43 6 Final procedures ..................44 - 3 - HDTV 1000 S...
The transmission of the DVB service information EIT as well as teletext (TXT), subtitle (SUB) and AC3 tone can be individually activated or deactivated. —> EIT (Event Information Table): For each service, event information is transmitted (such as starting time, duration, scrambling etc.). - 6 - HDTV 1000 S...
• Press any two keys on the control unit of the head-end station simultaneously until the display goes dark and the software version, e.g. "V 44" appears. Cassette After activating the cassette the software version of the cassette is displayed (see page 23). - 7 - HDTV 1000 S...
• Align the cassette and apply slight pressure to connect it to the connections of the board and the RF bus bar. • Fasten the cassette with the screws ACHTUNG! MESSAUSGANG Vor dem Cassettenwechsel unbedingt Netzstecker ziehen! CAUTION! Before changing cassettes remove mains plug! C LASS - 8 - HDTV 1000 S...
19" cabinet. Tighten the nuts on the cable terminals until the teeth on the lock washer have penetrated the exterior coating and a good connection is made between the hous- ing and cable terminals. - 9 - HDTV 1000 S...
—> In order to avoid restrictions of the network data rate (and therefore possible disturbances) we recommend to operate other applications like e.g. Internet, VOIP telephony etc. in separated networks. —> Exclusively use "Layer 3 switches", which support the IGMP protocol. - 10 - HDTV 1000 S...
CA module facing the top side of the cassette. • Push the CA module without canting into the guide rails of the CA slot and contact it to the common interface. - 11 - HDTV 1000 S...
The key pad on the head-end station is used to scroll through the menus: scrolls forward through the menus. select parameters in the menus. set values, initiate actions. selects sub-menus. scrolls backward through the menus. saves all entries. - 12 - HDTV 1000 S...
For special applications it is possible at a combination of cassettes HDTV 1000 S ("receiving cassettes") and HSPT 1000 T/C ("transmitting cassettes") to change the configuration quickly via "virtual station tables".
The head-end station can be pre-programmed with different station allocations via the station tables. Then the configuration can be switched over by the menu "Location" of the cassette HDTV 1000 S. The station tables are created using a text editor and stored e.g with the title "config.txt"...
P r o g r a m m i n g s tat i o n ta b l e s —> Programming for the receiving cassette HDTV 1000 S L "Name 1" Identifier for "Location" "Name 1"...
Page 19
I 1 , 0x6DCA , 0 , From the fourth setting on (behind the 3rd comma) the order is flex- ible! —> AC3 and EIT are so called "Flags" (software switches), which set certain PIDs. - 19 - HDTV 1000 S...
Page 20
Identifier for output settings. Output frequency (e.g. 474.00 MHz). Commas are the separators between the items 0x0001 Transport stream ID 0x0100 ORGNET-ID 6900 Symbol rate 1000…7500 (HSPT 1000 C) QAM modulation 64/256 (HSPT 1000 C) - 20 - HDTV 1000 S...
Page 21
—> Because of a more easily explanation the digits 1 and 2 are used in this example. In order to retain an overview, we recommend to use the same digit for the IP address as well as the station number (e.g. I 1,1). - 21 - HDTV 1000 S...
—> The software starts and loads the station tables included in the text file to the corresponding cassettes. —> The order of the cassettes is defined by the order of the hardware IP addresses which are assigned to the cassettes manually. - 22 - HDTV 1000 S...
—> The display shows e.g. the menu"Box 4 HOT-SPTS": "Box 4" stands for slot 4, "HOT-SPTS" type of cassette "V 4" software version of the cassette 192.168."0.128" hardware IP address of the cassette - 23 - HDTV 1000 S...
("stat"). To assign the cassette uniquely, each IPTV cas- sette must be allocated its own IP address. Bx 4 ETHERNET stat => Options • Press the buttons to select manual setting ("stat") or automatic setting ("DHCP") of the Ethernet parameters. - 24 - HDTV 1000 S...
IP address displayed to be set and use to set the IP address wished. • Press the button. —> The "Setting the address range" – "IP-MASK" menu is activated. - 25 - HDTV 1000 S...
IP address displayed to be set and use to set the IP address wished. • Press the button. —> The "Setting the UDP port" – "UDP-PORT" menu is activated. - 26 - HDTV 1000 S...
"– –" is displayed instead of "OK". —> Press the button to skip the settings of the input param- eters. The "Setting the output parameters" – "IP-OUT 1" menu is activated (page 31). - 27 - HDTV 1000 S...
The cassette recognizes the transmitted DVB mode and switches over between the normal QPSK mode (DVB-S) and the DVB-S2 mode. Receiving stations with DVB-S2 mode, we suggest to preset the DVB mode to shorten the time for searching stations. Bx 4A SYMBOL 27500 DVB-S - 28 - HDTV 1000 S...
• Press to set the input frequency. • Set the frequency offset shown in the display (e.g. "– 1.8") to less than 1 MHz by varying the input frequency using the buttons. - 29 - HDTV 1000 S...
Page 30
—> The "Selecting the input data stream" – "INPUT" menu is activated (page 27). —> If necessary set the input parameters of the further input signal sourc- • Press the button. —> The "Setting the output parameters" – " P-OUT 1" menu is activated. - 30 - HDTV 1000 S...
—> To skip the settings of the output parameters press the button. The "Stuffing the output data rate" – "DATAMODE" menu is activated. • Press the button. —> The "Setting the IP addresses for the services" – "OUT-IP" menu is activated. - 31 - HDTV 1000 S...
" for a short time. • Press the button. —> The "Switching the IP address off or on, selecting the transmission protocol, setting the port number" – "MODE / PORT" menu is acti- vated. - 32 - HDTV 1000 S...
Copying the settings to all IP outputs • Pressing the button the settings can be copied to the IP autputs following from the selected on. copy —> The display shows " " for a short time. - 33 - HDTV 1000 S...
IP 1 PKTS / FEC 10/09 AnnexB Setting the transmission channel • Press the button to position the cursor under "Annex…". • Use the buttons to set the transmission channel wished ("AnnexA" / "AnnexB"). - 34 - HDTV 1000 S...
—> Indication ">": Current needed data rate of this IP output is higher than the data rate set (overflow). Indication "!": The sum of all output data rates set is higher than 80 MBits. • Press the button. —> The "Allocating services manually" menu is activated. - 35 - HDTV 1000 S...
If the service selected is already allocated to an IP output, in the first line of the display an exclamation mark " ! " appears beside the type of the service. IP 1 TV ! 001/016 Das Erste - 36 - HDTV 1000 S...
"maximum" output data rate and will be customized is necessary. Bx 4 DATAMODE constant • Using the buttons select the data mode whished. • Press the button. —> The "Displaying the output data rate" – "DATARATE" menu is activated. - 38 - HDTV 1000 S...
"Selecting the station table" – "LOCATION" ("virtual station ta- bles" is activated) or "Setting the Ethernet parameters" – "ETHERNET" without ("virtual station tables" is not activated) saving the factory defaults (page 24). - 39 - HDTV 1000 S...
..—> By pressing the button you can skip the "Configuring the CA module" – "CA" menu and activate the "Selecting the input data stream" – "INPUT" menu (page 27). - 41 - HDTV 1000 S...
Page 42
• Press the button to leave the submenu. • Press the button to return to the "Configuring the CA module" – "CA" menu. • Press the button. —> The "Descrambling services" – "Edit" menu is activated. - 42 - HDTV 1000 S...
"0" The currently selected service remains unchanged. • Use the buttons to call up the services in sequential order which are to be descrambled, then use to descramble ("X") or to remain unchanged ("0"). - 43 - HDTV 1000 S...
EMC regulations securely. • Securely tighten the cable bolted connections using an appropriate open- ended spanner. • Mount the front cover (see assembly instructions of the head-end station). - 44 - HDTV 1000 S...
Page 45
Declaration of CE conformity - 45 - HDTV 1000 S...