Table of Contents
Advertisement
Quick Links
OPERATING MANUAL
TEMPERATURE CONTROLLER
TC-49
1 2 3
Note:
1) If Sensor Connection is reverse, Display will show "SRE" message.
2) If Sensor is not Connected, Display will show "OPN" message.
3) To Show set point, press
4) Auto out time is 15 sec without saving.
5) Every time the instument is turn on,following pattern will be displayed.
POWER ON
8
8 8
t c J
T P
3 0
Connection Diagram
TC-49
TC 49
°C
Key.
SET
SET
Display for 3 sec
display for 2 sec, according to the input
sensor programmed.
display for 2 sec, according to the control
action programmed.
Process Value
100
L
1
250V AC
50/60 HZ
~
4VA
N
2
3
4
5
Technical Specification
Technical Specification
Model
Display
3 Digit 7 seg 0.56",red LED Display
Size (mm)
48 (H) X 48 (W) X 70 (D) mm
Panel Cutout
Input
Temperature
Range
Control Action
1Relay, 1C/O Contact,10A, 230V AC
Output
S.S.R, 12V DC approx, 10mA DC.
Power Supply
100 to 250V AC,50/60 Hz, Approx 4VA
Protection
IP-65 (Front side) As per IS/IEC 60529 : 2001
Level
(As per request)
Operating
Temperature
Relative
Up to 95% RH Non Condensing
Humidity
~
8
7
7
T/C
+
!
9
-
SSR
10
NC
-
-
C
11
6
6
R1
NO
12
Page - 1
TC-49
44 X 44 mm
J TYPE/ K TYPE
J type: 0 to 600°C
K type: 0 to 999°C
TP/ ON-OFF (selectable)
0°C To 55°C
www.multispanindia.com
Advertisement
Table of Contents
Related Manuals for MULTISPAN TC-49
Summary of Contents for MULTISPAN TC-49
- Page 1 OPERATING MANUAL TEMPERATURE CONTROLLER TC-49 Technical Specification Technical Specification Model TC-49 Display 3 Digit 7 seg 0.56”,red LED Display TC 49 Size (mm) 48 (H) X 48 (W) X 70 (D) mm °C Panel Cutout 44 X 44 mm 1 2 3...
- Page 2 Control Action C T R ON-OFF O N F T P Press OffSet Point Setting to Save & Exit Password Message P A 5 0 0 0 * Ask to company person OFF-SET O F S (Range: -10°C to 10°C) O 0 0 Press to Save & Exit www.multispanindia.com TC-49 Page - 2...
- Page 3 Save & Exit 0 1 2 Manual Reset M R 0 0 0 Press to Save & Exit Range for J, K Parameter 1 To 15 4 To 30 -10°C to 10°C Hysteresis 1°C to 10°C Off-set correction -10°C to 10°C www.multispanindia.com TC-49 Page - 3...
- Page 4 3) Fusible resistor must not be replaced by operator. Product improvement and upgrade is a constant procedure. So for more updated operating information and support, Please contact our helpline : +91-9978991474/76/82 or Email at Service@multispanindia.com Ver: 05-2017 www.multispanindia.com TC-49 Page - 4...
Need help?
Do you have a question about the TC-49 and is the answer not in the manual?
Questions and answers
Tc 49 tem.125 se aage nhi ja rha h.
The MULTISPAN TC-49 troubleshooting steps for not moving forward include:
1. Check Key Operation: Ensure the correct key sequence is followed:
- Press SET + Up/Down key to set the set point.
- Press SET key to move to the next parameter.
- Release SET key to save the set point.
2. Verify Password Entry:
- For Basic Configuration, enter 73.
- For Control Parameter Setting, enter 37.
3. Power Supply Check:
- Ensure the power supply is properly connected and turned on.
- Avoid touching terminals while power is supplied.
4. Inspect Wiring:
- Check for proper wiring connections.
- Use wires with adequate ratings and ensure proper twisting to reduce electromagnetic interference.
5. Confirm Input and Control Action Settings:
- Ensure the correct Input Type (J/K) is selected.
- Check if the Control Action (TP or ON-OFF) is correctly configured.
6. Reset the Controller:
- If settings seem incorrect, reset parameters and reconfigure.
If the issue persists, refer to the manual for further support or contact the manufacturer's helpline.
This answer is automatically generated