Using The Blender; Cleaning And Maintenance - BRAYER BR1200WH Instruction Manual

6 EN
• Examine the unit for damages; if the unit is damaged,
do not plug it into the mains.
• Make sure that the indicated specifications of the
power supply voltage of the unit correspond to
the specifications of your mains. When the unit is
powered from 60 Hz frequency mains, no additional
actions are necessary.
• Remove the lid (2) and remove the measuring cup
(1).
• Wash the bowl (3), the lid (2) and the measuring cup
(1) with warm water and neutral detergent, rinse and
dry them.
• The cutting edges of the chopping knives (5) are
sharp and can be dangerous, handle the chopping
knives (5) carefully.
• Clean the motor unit body (7) with a soft, slightly
damp cloth, and then wipe it dry.
• Do not immerse the unit, the power cord and the
power plug of the unit into water or other liquids.

USING THE BLENDER

ATTENTION! Continuous operation time of the
blender should not exceed 1 minute, after that make
at least 1 minute break.
• Note: — when using the unit for the first time, a
foreign smell from the electric motor can appear —
this is normal and it is not covered by warranty.
• Place the blender on a flat dry and steady surface.
• Install the blender bowl (3) on the motor unit (7).
• Put the necessary ingredients into the bowl (3).
• Cover the bowl (3) with the lid (2).
• Insert the measuring cup (1) into the lid (2) opening.
• Notes:
- the blender is not intended for beating eggs,
making potato mash,
- kneading dough, extracting fruit or vegetable juice,
crushing hard or frozen products, chopping meat
and meat products.
- the amount of food for processing should not
exceed 2/3 of the capacity of the bowl (3) and
should not be below the minimal mark «600» on
the bowl (3).
- use the scale on the bowl (3) to control the amount
of products to process.
- before starting to chop/mix, we recommend to
peel fruit, remove stones, and cut fruit into 2х2 cm
cubes.
• Insert the power plug into the socket.
• Set the knob (9) to the position «ON», the illumination
(8) on the handle (9) will light up.
• To switch the blender on and select the chopping
knives (5) rotation speed set the knob (9) to a
position from «MIN» to «MAX».
• During the operation or between the operation
cycles, you can add the required ingredients into the
bowl (3). To do this, remove the measuring cup (1)
from the lid (2). After adding ingredients through the
lid (2) opening, install the measuring cup (1) back to
its place.
• After you finish using the unit, set the knob (9) to the
position «OFF», and unplug the unit.
BLENDER OPERATION MODES
• Set the knob (9) to the position «ON», the illumination
(8) on the handle (9) will light up.
• Press the button « » «SMOOTHIE» — cocktail
making, the button «SMOOTHIE» illumination will
light up and the blender will be switched on. To switch
the blender off press the button « » «SMOOTHIE»
again.
• To switch on the program « » «ICE CRUSHING» —
ice crushing, press the button «ICE CRUSHING»,
the button illumination will light up, and the blender
will be switched on in the ice crushing mode. To
switch the blender off press the button « » «ICE
CRUSHING» again.
• To switch on the pulse mode « » «PULSE», press
and hold the button «PULSE», the button illumination
will light up.
• After you finish using the unit, set the knob (9) to the
position «OFF», and unplug the unit.
• Note: — if food processing is hindered, you can add
some water, liquor or juice etc. into the blender bowl
(3).
EN

CLEANING AND MAINTENANCE

• Wash the bowl (3) preliminary, to do this pour
some water into the bowl (3) and add some neutral
detergent.
• Cover the bowl (3) with the lid (2) with installed
measuring cup (1).
• Insert the power plug into the mains socket.
• Set the knob (9) to the position «ON», the illumination
(8) on the handle (9) will light up.
• To switch on the pulse mode « » «PULSE», press
and hold the button «PULSE», the button illumination
will light up, after a few seconds release the button
«PULSE».
• After you finish washing the bowl, set the knob (9) to
the position «OFF», and unplug the unit.
• Remove the lid (2) from the bowl (3).
• Remove the bowl (3) from the motor unit (7), drain
the washing solution, wash the bowl, rinse it and dry.
• Wash the measuring cup (1), the lid (2) with warm
water and neutral detergent, rinse it and dry.
REMOVING AND INSTALLING THE CHOPPING
KNIVES (5)
• To remove the chopping knives (5) turn the lock
(6) counterclockwICE and remove it. Remove the
chopping knives (5) and the sealing gasket (4).
7