Using The Blender - BRAYER BR1201 Instruction Manual

6 en
• examine the unit for damages; if the unit is damaged,
do not plug it into the mains.
• Make sure that the indicated specifications of the
power supply voltage of the unit correspond to
the specifications of your mains. When the unit is
powered from 60 Hz frequency mains, no additional
actions are necessary.
• Remove the lid (2) and remove the measuring cup
(1).
• Wash the bowl (3), the lid (2), the measuring cup (1),
the lid (8) and the container (9) with warm water and
neutral detergent, rinse and dry them.
• The cutting edges of the knife block (5) are sharp
and can be dangerous, handle the knife block (5)
carefully.
• Take the chopper bowl (10), turn the knife block (12)
counterclockwise, remove the knife block (12) and
the gasket (11).
• Wash the chopper bowl (10), the knife block (only
from the knives side) (12) and the gasket (11) with
warm water and neutral detergent, rinse and dry.
• Clean the motor unit body (6) with a soft, slightly
damp cloth, and then wipe it dry.
• do not immerse the unit, the power cord and the
power plug of the unit into water or other liquids.

USING THE BLENDER

• The blender is used for chopping products, crushing
ice, mixing various ingredients and making cocktails.
ATTENTION! Continuous operation time of the
blender should not exceed 30 seconds, after that
make at least 1 minute break.
• Note: — when using the unit for the first time, a
foreign smell from the electric motor can appear —
this is normal and it is not covered by warranty.
• Place the blender on a flat dry and steady surface.
• Place the blender bowl (3) on the motor unit (6) and
turn it clockwise until bumping (pic. 1).
• Put the necessary ingredients into the bowl (3).
• Cover the bowl (3) with the lid (2).
• Insert the measuring cup (1) into the lid (2) opening.
• Notes:
- the blender is not intended for beating eggs,
making potato mash,
- kneading dough, extracting fruit or vegetable juice,
crushing hard or frozen products, chopping meat
and meat products.
- the amount of food for processing should not
exceed 2/3 of the capacity of the bowl (3) and
should not be below the minimal mark «200» ml
on the bowl (3).
- use the scale on the bowl (3) to control the amount
of products to process.
- before starting to chop/mix, we recommend to
peel fruit, remove stones, and cut fruit into 2х2 cm
cubes.
• Make sure once again that the blender bowl (3) is
installed correctly and is fixed.
• Insert the power plug into the socket.
• Note: — the blender will not be switched on if the
bowl (3) is installed incorrectly.
• Use the operation mode switch (7) to set the required
rotation speed of the knives:
- «1» (low speed) — for mixing liquid products;
- «2» (high speed) — for liquid and hard products.
- «P» pulse mode. To switch the pulse mode on,
turn the switch (7) to the position "P" and hold it.
• during the operation or between the operation
cycles, you can add the required ingredients into the
bowl (3). To do this, remove the measuring cup (1)
from the lid (2). After adding ingredients through the
lid (2) opening, install the measuring cup (1) back to
its place.
• After the unit operation is finished, set the operation
mode switch (7) to the «0» position and unplug the
unit.
• Remove the blender bowl (3) from the motor unit (6)
by turning it counterclockwise (Pic. 1).
• Remove the lid (2) from the bowl (3).
• Take the processed products out of the bowl (3).
• Wash the blender bowl (3).
• Note: — if food processing is hindered, add some
water, liquor or juice etc. into the blender bowl (3).
USING THE CONTAINER (9)
ATTENTION! Do not put hot products or carbonated
drinks in the container (9).
en
• Remove the knife block (5) from the blender bowl (3),
to do this, turn it counterclockwise.
• Notes:
• the amount of the processed products should not
exceed 2/3 of the container (9) capacity.
• before starting to chop/mix, we recommend to peel
fruit, remove stones, and cut fruit into 1х1 cm cubes.
• if food processing is hindered, you can add some
water, liquor or juice etc. into the container (9).
• Put the necessary ingredients into the container (9).
• Install the sealing gasket (4) on the knife block (5),
install the knife block (5) on the container (9) and turn
it clockwise (pic. 2).
• To avoid damage of the sealing gasket (4) when
turning the knife block (5), do not apply excessive
effort.
• Install the container (9) on the motor unit (6), slightly
press on it and turn it clockwise until bumping (pic.
3).
• Use the operation mode switch (7) to set the required
rotation speed of the knives:
- «1» (low speed) — for mixing liquid products;
- «2» (high speed) — for liquid and hard products.
- «P» pulse mode. To switch the pulse mode on,
turn the switch (7) to the position "P" and hold it.
ATTENTION! Continuous operation time should not
exceed 30 seconds, after that make at least 1 minute
break.
7