Section 4.2 Level Two: Access Screen; Section 4.3 Enter Passcode - Nabco GT1175 Wiring And Programming Manual

GT1175 Slide Door Opus Control Wiring and Programming Manual
P/N C-00391
Level One screens are used to inform the User all specifications that have already been programmed into the Opus Control. If a
specification needs to be changed, the User must reprogram the Opus Control within the Level Three screen, or Level Four screen.
When Power is turned ON for the first time, the Door does not move. Instead, an LCD screen will illuminate to display a Level One:
Unit Specification screen (Default screen).
Unit Specifications: Displays the type of door and current status of the unit. The type of door (swing, slide or folding)
There are (4) Level One screens:
can be changed within the Base Settings Category (Level 3 and Level 4). Please refer to Subsection Table 5 The screen
X above shows the Opus control installed on a GT710.
Error Specifications: This screen will only display an Error Code in the event there is an Error. Otherwise this screen
stays blank.
X
FLASHING
SCREEN
Short
Push
DN 2431
ANSI Specifications: Displays the actual time of opening and closing of the door to help determine ANSI compliance.
(Applies to swing doors only).
X
Terminal Specifications: Displays the current status of all of the Input/Output lines of the terminal strip.
X
SECTION 4.2 Level Two: Access Screen
Note: The "Activate Passcode" option is only displayed in the event "0045" had not already been entered.
LEVEL 2
Passcode
Go to Se ng menu
Stroke Learning
Yes No
Rotate
DN 1713 Dial
Attention: To prevent tampering, a Universal Passcode (0045) has been programmed into all Opus Controls. This
Passcode cannot be changed, but can be turned OFF and ON.
Attention: Do Not activate Passcode (0045) until programming of the Opus Control is complete. Failure to do so,
will force the User to enter (0045) each time a change is made.
SECTION 4.3 Enter Passcode
LEVEL 2
Passcode
Ac vate Passcode
Stroke Learning
Yes No
Reset to Default Set
0 0 4
If you don't know
the passcode,
Rotate
Keep Pushing Switch,
Dial Return to Normal mode
8 of 31
UNIT SPECS
GT1175 Opus Slide
Type: GT710 Swing
Fully Closed
Status: Slow Closing
Error: -----
Ac va on: IN EXT
Posi on: > > > > > > >
Other: BA 6B SLS
Keep Pushing Switch
=> Se ng Mode
Rotate
Dial
Passcode
Reset to Default Set
Stroke Learning
Yes No
Rotate
Dial
Reset to Default Set
0
If you don't know
Short
the passcode,
Keep Pushing Switch,
Push
Return to Normal mode
Reset to Default Set
0 0 4 4
If you don't know
Short the passcode,
Keep Pushing Switch,
Push
Return to Normal mode
ERROR SPECS
ERROR SPECS
Recycle Warning!
Recycle Warning!
Clear
Long
Figure 4 Example: Clear an Error Code for Recycle Warning
Push
Passcode
Go to Se ng Menu
Stroke Learning
Yes
Rotate
Dial
Reset to Default Set
0 0
If you don't know
Short
the passcode,
Keep Pushing Switch,
Push
Return to Normal mode
Reset to Default Set
0 0 4 5
If you don't know
Rotate
the passcode,
Keep Pushing Switch,
Dial
Return to Normal mode
www.NabcoEntrances.com
ERROR SPECS
Recycle Warning!
Yes No
Clear
Rotate
Dial
Passcode
Go to Se ng Menu
Stroke Learning
No
Rotate
Figure 5 Level Two Screen
Dial
Reset to Default Set
0 0 0
If you don't know
Short
the passcode,
Keep Pushing Switch,
Push
Return to Normal mode
Correct PassCode!
0 0 4 5
If you don't know
Short
the password,
Keep Pushing Switch,
Push
Return to Normal mode
Rev 8-11-21
No
Yes
Short
Push
Passcode
Ac vate Passcode
Stroke Learning
Yes No
DN 1715