During Use; After Use; Maintenance & Service - Raider RD-MG09 User Manual

14 www.raider.bg
• Ensure that the collet size corresponds with the shaft size of the accessory • Be sure tool is switched off when
plugging in

DURING USE

• Use auxiliary handle(s), if supplied with the tool (loss of control can cause personal injury) • Hold power tool by
insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its
own cord (a cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could
give the operator an electric shock) • Always keep the cord away from moving parts of the tool; direct the cord to the rear,
away from the tool • Never use the tool when cord is damaged; have it replaced by a qualified person • Never use spindle
lock while tool is running (damage due to improper handling will be excluded from the guarantee) • Keep hands away
from rotating accessories • When grinding metal, sparks are generated; keep other persons and combustible material
from work area • Keep the ventilation slots uncovered while working • In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug

AFTER USE

• The accessory continues to rotate for a short time after the tool has been switched off • Before you put down the
tool, switch off the motor and ensure that all moving parts have come to a complete standstill • After switching off the tool,
never stop the rotation of the accessory by a force applied against it • Store tool in locations where temperature will not
exceed 50°C WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY): • Do not connect the blue (= neutral) or brown (=
live) wire in the cord of this tool to the earth terminal of the plug • If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left unattended
USE
• Changing accessories ! switch off the tool and disconnect the plug ! ensure that collet size corresponds with shaft
size of accessory - push spindle-lock button and hold it while you turn collet nut by hand until the spindle lock prevents
further rotation and loosen collet nut with wrench - insert an accessory in collet as far as possible to minimize run-out
and unbalance - push spindle-lock button and hold it while you tighten collet nut with wrench ! avoid excessive tightening
of collet nut! never tighten collet nut, if there is no accessory in collet; collet may be damaged • Changing collets ! switch
off the tool and disconnect the plug - push spindle-lock button and hold it while you remove collet nut - remove collet -
insert new collet ! never tighten collet nut, if there is no accessory in collet; collet may be damaged • Before using the tool
- ensure that accessory is correctly mounted and firmly tightened - check if accessory runs freely by turning it by hand -
test-run tool for at least 30 seconds at highest no-load speed in a safe position - stop immediately in case of considerable
vibration or other defects and check tool to determine the cause • On/off switch - switch on/off the tool by pushing knob
in "I"/"O" position ! before the accessory reaches the workpiece, the tool should run at full speed
! before switching off the tool, you should lift it from the workpiece
• Speed control
For optimal results on different materials - select speed with wheel (also while tool is running).
Before starting a job, find the optimal speed by testing out on spare material ! after longer periods of working at low
speed, allow the tool to cool down by running it for approximately 3 minutes at high speed with no load • Holding and
guiding the tool - pencil grip for precision work (engraving) - one-hand grip for less precise work (grinding) - support grip
for additional control/comfort - do not apply too much pressure on the tool; let the speed do the work for you.
Flexible shaft - use flexible shaft for hard-to-reach places
Changing accessories when using flexible shaft - pull sleeve down (= lock spindle) and hold it while you turn collet
nut by hand until the spindle lock prevents further rotation and loosen collet nut with wrench - insert an accessory in
collet - pull sleeve L down (= lock spindle) and hold it while you tighten collet nut with wrench.
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation slots) ! disconnect the plug before cleaning • If the tool should
fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service
centre for RAIDER power tools - send the tool undismantled together with proof of purchase to your dealer or the nearest
RAIDER service station.
ENVIRONMENT
• Do not dispose of electric tools, accessories and packaging together with household waste material (only for EU
countries) - in observance of European Directive 2012/19/EC on waste of electric and electronic equipment and its
implementation in accordance with national law, electric tools that have reached the end of their life must be collected
separately and returned to an environmentally compatible recycling facility.