Raider RD-AG66 User Manual page 8

14 www.raider.bg
GENERAL GUIDELINES FOR SAFE OPERATION
Read all instructions carefully. Failure of the nature following instructions can cause electric shock, fire
and / or severe injuries. Keep these instructions in a safe place.
1. Safety in the workplace.
1.1. Keep your workplace clean and well lit. Disarray and poor lighting may contribute to the occurrence
of an accident.
1.2. Do not operate in an environment of grinding increased the risk of explosion, close to flammable
liquids, gases or powders.
During operation of the separate grinding sparks that can ignite powders or fumes.
1.3. Keep children and bystanders at a safe distance while working with angle grinders.
If your attention is diverted, you may lose control over grinding.
2. Safety when working with electricity.
2.1. Plug the grinding must be suitable for contact. In no case is allowed to modify the structure of the
plug. When working with electrical zero, do not use plug adapters.
Using original plugs and sockets reduces the risk of electric shock.
2.2. Avoid touching your body to earthed bodies, for example pipes, heaters, stoves and refrigerators.
When your body is grounded, risk of electric shock is greater.
Keep grinding from rain and moisture.
Infiltration of water into the grinding increases the risk of electric shock.
2.3. Do not use a power cord for the purposes for which it is not provided, for example to carry grinders
for cable or removing the plug from the outlet. Protect cords from heat, oil and contact with sharp
edges or points of mobile machines.
Damaged or twisted cables increase the risk of electric shock.
2.4. When you work with the angle grinder out, switch the machine only in installations equipped
with electric switch "Fi" RCD (Residual Current Device). RCD must be no more than 30 mA. Use an
extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
2.5. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
Using the extension, designed for outdoor use reduces the risk of electric shock.
3. Safer way of working.
3.1. Be concentrated, watch their actions carefully and act cautiously and prudently. Do not use the
angle grinder when you are tired or under the influence of drugs, alcohol or narcotic drugs.
A moment of distraction at work grinding may have the effect of extremely serious injuries.
3.2. Work with protective work clothing and always with safety glasses.
Wearing Suitable for grinding and the activities of personal protective equipment, such as respiratory
masks, healthy, tightly closed shoes grapple with a stable, protective helmet and silencers (hearing
protectors), reduces the risk of accident.
3.3. Avoid the danger of incorporating the grinding inadvertently. Before you turn the plug into the
power supply network, make sure the trigger switch is in position "off". If you wear when grinding,
keep your finger on the trigger switch, or if you submit a voltage of grinding when turned on, there is
the risk of accident.
3.4. Before you turn implies that we are sure you remove all of its utilities and wrenches.
Utilities, forgotten rotating unit can cause injuries.
3.5. Avoid unnatural positions of the body. Work in a stable position of the body at any time and keep
the balance. So you can control the grinding better and safer if unexpected situations arise.
3.6. Work with appropriate clothing. Do not operate with loose clothing or ornaments. Keep your hair,
clothes and gloves at a safe distance from rotating the grinding units. Robes, attire, long hair can be
caught and carried away by rotating units.
3.7. If it is possible to use external aspiration system, make sure it is switched on and functioning
properly. Use of the aspiration system reduces the risks due to the discharge dust at work.
4. Thoroughly respect to angle grinders.
4.1. Do not overload grinders. Use angle grinders only as intended. You will operate better and safer
when using the right angle grinder manufacturer in the specified range of load.
4.2. Do not use the angle grinder with a starting switch is damaged.
Angle grinder, which can not be excluded and included as intended by the manufacturer, is dangerous
and should be repaired.
4.3. Before you modify the settings of the angle grinder to replace work tools and additional accessories
as well as a long time when you will not use grinders, unplug the plug from the supply network. This
measure eliminates the danger of triggering the grinding inadvertently.
4.4. Keep grinding in places where they can be reached by children. Do not allow them to be used by
persons who are not familiar with how to work with them and have not read those instructions. When
you are in the hands of inexperienced users, grinders can be extremely dangerous.
4.5. Keep grinding their care. Check whether the mobile units operate impeccable, whether it spells, if
there is a broken or damaged item which distort or alter the functions of the grinding machine. Before
using the angle grinder, make sure that the damaged parts to be repaired. Many accidents are caused
by poorly maintained power tools and appliances.
4.6. Use the angle grinder, attachment, working tools according to the manufacturer's instructions. In
doing so must comply with specific operating conditions and operations to perform. Using grinders of
various applications provided by the manufacturer increases the risk of accidents.
5. Maintain.
5.1. Repairing your electric tools is best carried out only by qualified specialists in workshops RAIDER,
which used only original spare parts. Thus it ensuring their safe operation.
6. Guidelines for the safe handling, specific grinding purchased by you. General guidelines for safe
operation with a disc grinder and sandpaper, clean with wire brush and abrasive cutting disk.
6.1. This grinding can be used for grinding with carboflex drive and sandpaper, clean with wire brush,
polishing and cutting carboflex disk. Follow all instructions and warnings complying with technical
parameters and the adjusted images. Failure to follow the following instructions, the consequences
may be an electric shock, fire and / or severe injuries.
6.2. This angle grinder is not suitable for polishing. Carrying out activities for which the grinding is not
intended, may be dangerous and cause injuries.
6.3. Do not use additional devices which are not recommended by the manufacturer for this particular
power. The fact that you can attach to specified device or machine working tool does not ensure safe
working with him.
6.4. Allowable speed of rotation of the working tools must be at least equal to the inscribed plaque on
the grinding speed of rotation. Working tools that rotate at a higher speed than the maximum indicated
15