Table of Contents
Advertisement
Ratings and Performance
E3FS-10B4 2M/E3FS-10B4-M1-M
Sensing method
Controller
Supply voltage
Effective aperture angle (EAA)
Current consumption
Sensing distance
Standard sensing object
Response time
Control output
Test input (Emitter)
Power supply reset time
Ambient light intensity
Ambient temperature
Ambient humidity
Insulation resistance
Dielectric strength
Malfunction
Vibration
resistance
Operating limit
Malfunction
Shock
resistance
Operating limit
Degree of protection
Light source
Operation indicators
Protection
Weight (in packaging)
Applicable standard
Accessories
Engineering Data
Parallel Operating Range
600
Emitter
Y
400
X
Receiver
200
0
−200
−400
−600
0
2
4
6
8
Single-beam Safety Sensor
Through-beam
F3SX Series
24 VDC±10% (ripple p-p 10% max.) (Connect the Sensor to an F3SX to use it as a safety device or
as part of a safety system.)
±5° (at 3 m)
Emitter:
50 mA max.
Receiver: 25 mA max.
10 m
Opaque object: 11 mm min. in diameter
2.0 ms (E3FS only) (Depends on the F3SX model when the Sensor is connected to an F3SX.
Refer to the F3SX operation manual for details.)
PNP transistor output, load current: 100 mA max., residual voltage: 2 V max.
(except for voltage drop due to cable extension)
(Connect the Sensor to an F3SX to use it as a safety device or as part of a safety system.)
21.5 to 24 VDC: Emitter OFF (source current: 3 mA max.)
Open or 0 to 2.5 V: Emitter ON (leakage current: 0.1 mA max.)
(Connect the Sensor to an F3SX to use it as a safety device or as part of a safety system.)
100 ms
Incandescent lamp: 3000 lx max. (light intensity on the receiver surface)
Sunlight: 10,000 lx max. (light intensity on the receiver surface)
Operating: −10 to 55°C, storage: −30 to 70°C (with no icing or condensation)
Operating: 35% to 85%, storage: 35% to 95% (with no icing or condensation)
20 MΩ min. (at 500 VDC)
1000 VAC 50/60 Hz 1 min
10 to 55 Hz, double amplitude: 1.5 mm, 2 h each in the X, Y, and Z directions
10 to 55 Hz, double amplitude: 0.7 mm, 50 min each in the X, Y, and Z directions
2
500 m/s
(approx. 50 G), 3 times each in the X, Y, and Z directions
2
100 m/s
(approx. 10 G), 1000 times in the X, Y, and Z directions
IP67 (IEC standard)
Infrared LED
Emitter: Emitting (orange)
Receiver: Output ON (green), Output OFF (red)
Output short-circuit protection, reverse polarity protection
E3FS-10B4 2M (ABS resin case): approx. 150 g for 1 set (weight without cable: approx. 55 g)
E3FS-10B4-M1-M (metal case): approx. 125 g for 1 set
IEC61496-1, EN61496-1 Type 2 ESPE (Electro-Sensitive Protective Equipment)
IEC61496-2, prEN61496-2 Type 2 AOPD (Active Opto-electronic Protective Devices)
Emitter, two nuts for mounting the Receiver, and an instruction manual
Mutual Interference Range
800
Y
600
Receiver
400
200
0
−200
−400
−600
−800
0
8
10
12
Distance X (m)
E3FS
Emitter
X
2
4
6
8
10
Distance X (m)
Reception Light Output Margin
10
9
8
7
6
5
4
3
2
1
0
12
0
5
10
15
20
25
30
Distance (m)
Advertisement
Table of Contents
