Technical Characteristics; Introduction; Installation - Cecilware MT-2-ULAF Operator's Manual

MT UL AF Black

1 TECHNICAL CHARACTERISTICS

Transparent removable bowls
Capacity of each bowl, approx.
Dimensions:
width
depth
height
Net weight, approx.
Gross weight, approx.
Adjustable thermostats
Hermetic compressor
Air-cooled condenser
Overload protector
Noise level lower than 70 dB (A)
IMPORTANT
Read electrical ratings written on the data plate of the
individual units; the data plate is adhered on the
dispensing side panel of the unit, just behind the drip
tray (the right side drip tray in multiple bowl models).
The serial number of the unit (preceded by the
symbol #) is adhered inside the left switch box. Data
plate specifications
information in this manual.
The electric diagram of the dispenser is located in the
inner part of the dispensing side panel.
Specifications are subject to change without notice.

2 INTRODUCTION

Please read all sections of this manual thoroughly to familiarize
yourself with all aspects of the unit.
Like all mechanical products, this machine will require cleaning
and maintenance. Besides, dispenser working can be
compromised by operator's mistakes during disassembly and
cleaning. It is strongly recommended that personnel
responsible for the equipment's daily operations, disassembly,
cleaning, sanitizing and assembly, go through these
procedures in order to be properly trained and to make sure
that no misunderstandings exist.

3 INSTALLATION

1 - Remove the corrugate container and packing materials
4
n 1
l 10
cm 28
cm 47
cm 69
kg 26
kg 29
n 1
will always supersede
and keep them for possible future use.
When handling the machine never grasp it by the bowls
2 3
or by the evaporator cylinders. The manufacturer
10 10
refuses all responsibilities for possible damages which
may occur through incorrect handling.
36 54
2 - Inspect the uncrated unit for any possible damage. If
47 47
damage is found, call the delivering carrier immediately to
file a claim.
69 69
3 - Install the unit on a counter top that will support the
37 49
combined weight of dispenser and product bearing in
40 54
m i n d w h a t i s s t a t e d i n t h e p r e c e d i n g p o i n t 1
IMPORTANT warning.
2 3
4 - A minimum of 15 cm (6") of free air space all around the
unit should be allowed to guarantee adequate ventilation.
5 - Ensure that the legs are screwed tightly into the base of
the machine.
Replace the standard legs originally installed with the 100
mm (4") legs whenever they are provided with the unit.
6 - Before plugging the unit in, check if the voltage is the same
as that indicated on the data plate. Plug the unit into a
grounded, protected single phase electrical supply
according to the applicable electrical codes and the
specifications of your machine. When the unit has no plug,
install a proper grounded plug, in compliance with
electrical codes in force in your area, suitable to at least
10 Amp 250 Volt (220-230 Volts 50-60 Hz areas) and
20 Amp 25 0 Vol t (1 00-1 15 Vol ts 5 0-6 0 Hz area s)
applications. Should you prefer to connect the unit directly
the
to the mains, connect the supply cord to a 2-pole wall
breaker, whose contact opening is at least 3 mm. Do not
use extension cords.
Failure to provide proper electrical ground according to
applicable electrical codes could result in serious shock
hazard.
7 - Each drip tray has two diaphragm plugs: if a continuous
drain is needed, perforate one of the drain plugs and
connect it to a flexible drain line (see figure 1).
8 - The unit doesn't come presanitized from the factory.
B e f o r e s e r v i n g p r o d u c t s , t h e d i s p e n s e r m u s t b e
IMPORTANT
ATTENTION
figure 1
Ugolini spa