Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Signode Manuals
  4. Label Maker
  5. LITTLE DAVID LX600
  6. Operator's manual

Signode LITTLE DAVID LX600 Operator's Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Label Application System
LX600 Apply Only Labeling System
PN: LSMANUAL-LX600
Version: 05B (For use with the Allen-Bradley Micro830 ™ PLC)
Operator' s Manual

Advertisement

loading

Summary of Contents for Signode LITTLE DAVID LX600

  • Page 1 Label Application System LX600 Apply Only Labeling System PN: LSMANUAL-LX600 Version: 05B (For use with the Allen-Bradley Micro830 ™ PLC) Operator’ s Manual...
  • Page 2 L A B E L A P P L I C A T I O N S Y S T E M Labeler Operation Copyright  Loveshaw 2014-2020 LOVESHAW 2206 Easton Turnpike, PO. Box 83 South Canaan, PA 18459 Tel: 1-800-962-2633 • 570-937-4921 Fax: 570-937-4016 www.loveshaw.com Loveshaw Europe...

  • Page 3: Table Of Contents

    T able of Contents Chapter 1: Introduction Chapter 2: Operating Safety Chapter 3: Overview Chapter 4: Installation and Threading Section 1: Placing the Mount. Section 2: Threading the Label Stock Chapter 5: Theory of Operation Chapter 6: Product Sensing and Time Delay Chapter 7: Applicators and Gap Sensor Gap Sensor and Label Placement to Peel Edge Standard Straight Tamp Cylinder (200mm stroke)
  • Page 4 Chapter 9: Features and Options Warning Light Assembly Cleanable Vacuum Filter Air Dryer Spare Parts Kits Chapter 10: Controller Operation Chapter 11: Maintenance Chapter 12: Warranty and Label Converting Specifications Chapter 13: Assemblies and Schematics SEE SECTION FOR DETAILED ORGANIZATION OF DRAWINGS...

  • Page 5: Chapter 1: Introduction

    Chapter Introduction hank you for purchasing the Little David™ model LX600 series Apply Only labeler. The LX600 series apply only labelers are I C O N K E Y designed to be versatile enough to suit a variety of carton labeling requirements with one standard unit.

  • Page 6: Chapter 2: Operating Safety

    Chapter Operating Safety Observe the warnings and cautions below when using the Little David Label Application Systems. Within this manual, a warning indicates that the potential for bodily injury exists, and a caution indicates when the machine may suffer damage. Instruction: Requirement for System Operation Instruction: Socket-outlet shall be installed near the equipment and shall...
  • Page 7 Thereafter, refer to it as necessary. Take special note of all warnings, cautions, and maintenance instructions. Like any other piece of equipment, the Little David LX600 Label Application System functions best when cared for and used carefully. Note that only an authorized technician should perform any procedures not described in this manual.
  • Page 8 Safety Decal Locations...
  • Page 9 Safety Decal Part Number...

  • Page 10: Chapter 3: Overview

    Chapter Labeler Sections Overview This manual covers several parts of the machine. The following diagram identifies the key sections of the machine.

  • Page 11: Chapter 4: Installation And Threading

    Chapter Installation and Threading lways check for any signs that the machine may have been damaged  before fully removing it from the shipping skid. Section 1: Placing the Machine The labeler comes fully assembled and already on the mounting stand.
  • Page 12 Take care removing the machine from the Step Two: skid as it weighs approximately 190 pounds depending on configuration and options. Step Three: You will need to move and orient the label machine along your production line in a position relative to your label and product. A.
  • Page 13 B. Alternatively or additionally, you may want to turn the machine vertically. This is done with the handle found behind the machine. Note: If the machine is to be inverted (sometimes called bottom labeling) the handle should be completely removed to move the machine upside-down.
  • Page 14 Refer to Section 2: Threading the Label Stock.
  • Page 15 Section 2: Threa ading th he Label Stock Always m make sure that the power is is off, the e unit is unplugged d, and no o product is moving g past the he labeler before thre eading ne ew label st stock or re e-threading ng after a...
  • Page 16 Step Three: Take the Label Liner / Web back under the peel edge. Make sure that the liner threading path does not go over the Blow Tube when you take the label liner/ web back under the peel edge blade. Next release the knurled friction roller with the black knob.
  • Page 17 The labeler is now threaded and ready to be plugged in and turned on. You can use the JOG selection on the PanelView Touch Screen of the control box to advance one label onto the applicator. If the label comes out too far or not far enough, make a manual adjustment to the gap sensor position along the slotted bracket.

  • Page 18: Chapter 5: Theory Of Operation

    Chapter Theory of Operation Apply Only Labeling Straight Tamp (Touch and Go Linear Applicator) or Swing Arm Applicator. The LX600 Apply Only Labeling system is configured in either a Straight Tamp (Linear Actuator) with a “Touch and Go” Sensor or with a Rotary Actuator that would provide for a “Swing Arm” type Label Application for various label application scenarios.
  • Page 19 Chap pter Produc ct Sen nsing Proximit ty Photo o-eye Sensor P/N N: E7763- P1-LX The labeler o operates wh hen it gets a a signal from m the produ uct sensor elling it tha at the prod duct is in place to re eceive the label.
  • Page 20 Chapter Applicators and Label placement Peel Edge (Gap Sensor) Gap Sensor Note: The Gap Senor Sensitivity and label position is preset Gap Sensor at the factory. However if no labels are provided, a suitable Sensitivity labels is used for testing and run off. Label placement and gap sensor fine tuning may be required at installation and or label changes.
  • Page 21 Sensitivity is adjusted from the control module located on the back of the unit near the top of the frame. A potentiometer located on the control module adjusts the sensitivity gain. LED indicators on the control module will illuminate when this is transition occurs.
  • Page 22 A desired position for the leading edge of the label should be approximately 1/8 to 1/16 inch from the edge of the peed edge. Note: For longer labels, let the trailing edge of the label touch the liner once it is dispensed to the pad. This will to assist with label alignment to the pad.
  • Page 24 Standard rd Stroke e Tamp (200mm m / 8”) Assembly P/N: .914- -LX-ST or further details on assemby bly components, see Chapter r 12. Adjustin g the Ap pplicato or (Stand dard Stro oke) The applica ator has on nly three a adjustments s;...
  • Page 25 Background Suppressed Sensor P/N: E7367-BS2 The tamp applicator uses a sensor to detect when the applicator Adjusting the has made contact with your product. It may be necessary to adjust Applicator the sensitivity or range of this sensor to apply the label to your Stroke Length desired specifications.
  • Page 26 Optional Extended Stroke Tamp (350mm / 14”, 400mm / 16", 500mm / 20”, 600mm / 24") Assembly P/N’s: .914 - LX - 350 .914 - LX - 400 .914 - LX - 500 .914 - LX - 600 For further details on assembly components, see Chapter 12. Adjusting the Applicator The applicator has four adjustments;...
  • Page 27 With the air r off and th he power o on, extend t the cylinder r until the applicator pa ad touches the surface e to be label led and then n turn the dial until the e yellow ind dicator ligh ht has just t turned on.
  • Page 28 Dual Tam mp (Swi ing Arm Applicat Assembly P/N: .914 4 - LX – DT/ /RH or LH or further details on assemby bly components, see Chapter r 12. Adjustin g the Ap pplicato The DT (Sw wing Arm) applicator has severa al adjustmen nts;...
  • Page 29 To make small pitch adjustments between the peel blade and the applicator pad edge, loosen the (6) screws (3 each side) on the applicator pad mount arm and adjust accordingly. Re-tighten screws. Typically, a 1/8” gap is a good starting point. Adjusting the Depending on your label size, you may need to move the pad Applicator...
  • Page 30 Adjusting the To fine tune the applicator pad home position, loosen the jam nut on the stop adjusting bolt and adjust the home stop as needed to Applicator allow proper label feed onto the applicator pad. Typically, the Pad Home applicator pad is adjusted in the same plane and slightly behind Position the peel edge.
  • Page 31 Adjusting the After locating the labeler in the application area and locking down the casters, manually swing the application arm out to insure it Swing Arm can apply the label squarely to the box or product. If the Maximum applicator pad doesn’t place the label squarely on the product Application (arm stops short of being parallel with application area), you may Angle...
  • Page 32 vacuum pad. Adjusting the position is covered here while adjusting the air pressure is covered in Chapter 11 Maintenance as it requires removal of the rear cover. Blow Tube Assembly P/N: .14018-LT The air tube is just to function as an assist. The label will want to Adjusting the curl away from the vacuum pad for various reasons and the blow Blow Tube...

  • Page 33: Chapter 8: Pneumatic System

    Chapter Pneumatic System Air Filter and Shut-Off See Chapter 12 for Detailed for Pneumatic Drawings and individual part numbers The air filter and shut off valve is located at the back of the stand and is positioned so that you can bleed your air lines before introducing air into the labeling system.

  • Page 34: In Line Air Filters

    the Cylinder Size and Pad configuration. In the event that the regulator is not at this value; consult Chapter 11, Maintenance. In-Line Air Filters – P/N: 14199 For tamp applicators, there are two vacuum line filters on the exterior of the machine. They will keep most debris from entering the vacuum system and clogging the lines.
  • Page 35 Chapter Features and Options Feature: Scrolling Message Status Screen: On the PanelView HIM Main Screen, a scrolling Machine Status screen is provided to alert the operator of various operational conditions of the Machine Status and other Diagnostic Notifications:. Some of these conditions are: Machine Ready, No Faults, No Labels or Web Break and Low Labels if the Optional Low Label Sensor is ordered with the system.
  • Page 36 Optiona al: Clea nable V Vacuum m Filter P/N: P3587 7-C1 Loveshaw o offers a in-li ine cleanab ble vacuum air filter th hat can be opened and cleaned of dirt and deb bris. Optiona al: Air D Dryer P/N: P3587 7-D1 Preceding yo our main-lin...
  • Page 37 Optional: Spare Parts Kit (Standard Stroke Straight Tamp) - 120/1/60 P/N: .SPK-LX6-T Spare Parts Kits contain common wear parts conveniently in one kit. The list of components is as follows:  N698-FR (Filter / Regulator Gauge Qty-1)  E7367-BS2 (Background Suppressed Sensor Qty-1) ...
  • Page 38 Optional: Spare Parts Kit (Straight Tamp) - 230/1/50-60 P/N: .SPK-LX6-T-230 Spare Parts Kits contain common wear parts conveniently in one kit. The list of components is as follows:  N698-FR (Filter / Regulator Gauge Qty-1)  E7367-BS2 (Background Suppressed Sensor Qty-1) ...
  • Page 39 Optional: Spare Parts Kit (Dual Tamp – Swing Arm) - 120/1/60 P/N: .SPK-LX6-DT Spare Parts Kits contain common wear parts conveniently in one kit. The list of components is as follows:  N698-FR (Filter / Regulator Gauge Qty-1)  A125SB-10-326 (Fuse, 10A, 250V, Time Delay, Qty-5) ...
  • Page 40 Chapter Controller Operation Overview his section will cover the controller aspects of the machine and how to change the cycle functions of the labeler. From here you will learn how to:  Typical Views of Panel View Screen Boot Sequence ...
  • Page 41 Upon energizing the labeler, the touch screen can take up to 60 – 70 seconds to load information from the PLC before it can be utilized. The following screens will be displayed on power up. After the touch screen initializes, the main application screen will appear.
  • Page 42 and the display will give various machine status (i.e. MACHINE READY, NO FAULTS, etc.) The main screen will boot up in the Stop condition. The general operator screen navigations will be from this main screen once the system is set up. If you want to JOG a label out to the applicator pad, depress the JOG button which will momentarily turn black, then return to the STOP.
  • Page 43 With a Dual Tamp Applicator, in the SET UP mode, the operator must determine the mode of operation of the Swing Arm first (Single Tamp or Dual Tamp) before changing any of the induvial timers. The following screens are used to configure between a Single Tamp mode (i.e.
  • Page 44 made timer changes and has selected and pressed the 1 in the box. When selected the state of the selected preset changes to a black background indicated that this preset timer (SAVE AREA) was selected. This timer change sequence is also similar for the Swing Arm applicator and Straight Tamp mode settings.
  • Page 45 To change a time value, press the appropriate timer box to be changed and the next screen will appear: Press the timer box to activate the cursor. Use the arrow up, down, left, right to change time. Enter / return will save the new values and return to the previous...
  • Page 46 There are five screens each having a separate save areas. Pressing ESC will access the Main Screen; pressing NEXT will scroll through the save areas. To change a timer value, follow the same procedures previously outlined. Notice there are four timers required for the Dual Tamp mode. PROD DLY1 (Product Delay 1) is the time delay between the product sensor sensing the leading edge of the product to when the applicator applies the first label;...
  • Page 47 Note: If Config button was pressed and it was not intend to enter this screen, simply cycle power to the unit which will reboot the PanelView screen to normal screen function. Should a Config screen require access, contact the factory for further instructions.
  • Page 48 Chap pter Mainte enanc n norma al operation, the labeler is s simply turn ned-on and p products are moved p past its sensor r equipment a and the labele er responds b by feeding a label to the applicat or pad then n applying th he label to t...
  • Page 49 Blow Tube Pressure The Blow Tube (P/N: .14018-LT) that guides the label onto the pad from the dispensing edge of the printer is regulated by a flow control. DO NOT increase air pressure to the system. Adjust the blow tube flow control. Air Pressure and Regulation The incoming air pressure of the machine should not exceed 100psi.
  • Page 50 Motor and Chain Maintenance Your label machine utilizes a Servo motor and chain along with a slip clutch to rewind the waste paper from your label roll. DO NOT Work on any porting of the motor or chain maintenance / ...
  • Page 51 Chain Path and Tension Adjustment (Note: Transparent view to observe chain path shown above.) Electrical Control Box Your system uses an Allen-Bradley Micro830 ™ PLC to control its function along with a series of terminal blocks and relays. A copy of the PLC program is available upon request for your reference.
  • Page 52 Chapter Warranty For: LABELING SYSTEMS 1 YEAR WARRANTY (EXCEPT FOR MOVING PARTS WHICH ARE SUBJECT TO NORMAL WEAR, TEAR AND REPLACEMENT WHICH ARE WARRANTED ONLY TO BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP). ABOVE WARRANTY EXCLUDES CUSTOMERS SELECTED THERMAL TRANSFER PRINTER OR MATERIAL HANDLING SYSTEM. PRINTER AND/OR CONVEYOR WARRANTY AVAILABLE UNDER SEPARATE COVER.
  • Page 53 LABEL CONVERTING SPECIFICATIONS In order to insure the labeling machines function, the following label specifications are offered as part of this proposal. Seller recommends that Buyer include a copy of these specifications with Buyer’s purchase order for labels from Buyer’s label converter. There may be exceptions to these specifications, depending upon the particular label construction used.
  • Page 54 Chapter Assemblies and Schematics This section contains assembly drawings and schematics required to repair or rebuild your label machine. The drawings are organized under the following sub-headings. 1. Main Frame and Stand Assemblies (for all models) 2. Pneumatic Assemblies (for all models) 3.
  • Page 55 MAIN FRAME AND STAND ASSEMBLIES (FOR ALL MODELS)
  • Page 58 REVISION HISTORY DESCRIPTION DATE RELEASED 11/3/2011 NOTE: THE THREE BASE CONFIGURATIONS ARE ALL BOLT TOGETHER CONSTRUCTION BUILT FROM THE (7) FRAME PIECES. STANDARD STAND ALONE LX SERIES MOUNTING STAND ALONE MOUNTING WITH HORIZONTAL SLIDE CONVEYOR INTEGRATED MOUNTING HORIZONTAL SLIDE WITH HORIZONTAL SLIDE HORIZONTAL SLIDE MOUNTING HARNESS HAS THREE MOUNTING LOCATIONS;...
  • Page 59 Parts List ITEM PART NUMBER DESCRIPTION LABN-0172-4 MOUNTING EAR RECIEVER LABN-0173-4 MOUNTING ARM LABN-0174-5 BASE, MOUNTING ARM FSHSH075B05 SHCS 5/16-18 X 3/4 LG. FSHSJ100B05 SHCS 3/8-16 x 1" LG Loctite Application Note: 277 is RED Loctite 242 is BLUE Loctite LOVESHAW 538 is GREEN Loctite MAT'L...
  • Page 60 Parts List ITEM PART NUMBER DESCRIPTION ---------------------------- FRICTION ROLLER ASSY. ---------------------------- FRICTION RELEASE ROLLER ASSY. ---------------------------- LABEL ROLL CORE ASSY. ---------------------------- DANCER ARM ASSY. ---------------------------- REWIND ASSY. ---------------------------- PEEL EDGE ASSY. ---------------------------- ANTI STATIC ASSY. ---------------------------- GUIDE ROLLER ASSY. LABN-0193-3 PHOTOEYE BRACKET A219-PF-7 PHOTO EYE...
  • Page 61 Parts List ITEM PART NUMBER DESCRIPTION LABN-0187-6 LX600 MAIN PLATE LABN-0155-6 FRAME SIDE, SMALL LABN-0159-4 MOTOR MOUNT LABN-0160-3 MOTOR MOUNT SHAFT LABN-0181-4 CONDUIT CONNECTION LABN-0171-4 STAND MOUNTING EAR FLWSDP LOCK WASHER 1/4 FHHSE075P08 HHCS 1/4-20 x 3/4 LG FHHSH100P08 HH 5/16-18 x 1 LG. FLWSEP LOCK WASHER M8 FSBSH200P05...
  • Page 62 Parts List ITEM PART NUMBER DESCRIPTION -------------------- FRICTION ROLLER LABN-0179-6 CHAIN GUARD -------------------- IDLER ASSY. -------------------- DANCER ARM ASSY. -------------------- REWIND ASSY. FSHSD050P05 10-32 X 1/2 SHCS FLWSCP #10 LOCK WASHER LABN-0193-3 PHOTOEYE BRACKET A219-PF-7 PHOTO EYE FFHSB050B05 FHCS #8-32 x 1/2 FBHMD018P10 BH M3 x 18mm FFWMDP...
  • Page 63 Parts List ITEM PART NUMBER DESCRIPTION 01040-7 LABELING HEAD POST LABN-0187-6 LX600 MAIN PLATE LABN-0155-6 FRAME SIDE, SMALL LABN-0156_-4 GAP SENSOR SLIDE, L/R HC-1063 THUMB SCREW LABN-0158-3 GAP SENSOR MOUNT FLWSDP LOCK WASHER 1/4 FHHSE075P08 HHCS 1/4-20 x 3/4 LG FHHSH100P08 HH 5/16-18 x 1 LG.
  • Page 64 REVISION HISTORY DESCRIPTION DATE RELEASED 8/4/2015 Loctite Application Note: 277 is RED Loctite 242 is BLUE Loctite 538 is GREEN Loctite / is no Loctite applied Parts List ITEM PART NUMBER DESCRIPTION LABN-0145-4 LABEL CORE LABN-0146-4 CORE SHAFT .01956 CLAMP ASSY - LET OFF 01044 12"...
  • Page 65 REVISION HISTORY DESCRIPTION DATE RELEASED 8/5/2015 Parts List ITEM PART NUMBER DESCRIPTION M0010-017 IDLER ROLLER SHAFT 01054 TEFLON IDLER ROLLER FBHSE100P05 1/4-20 X 1 BHS FLWSDP LOCK WASHER 1/4 Loctite Application Note: 277 is RED Loctite 242 is BLUE Loctite 538 is GREEN Loctite / is no Loctite applied LOVESHAW...
  • Page 66 REVISION HISTORY DESCRIPTION DATE Loctite Application Note: RELEASED 8/4/2015 277 is RED Loctite 242 is BLUE Loctite 538 is GREEN Loctite / is no Loctite applied 1.1.1 1.1.1 Parts List ITEM PART NUMBER DESCRIPTION .01990 ROLLER ASSY. RUBBER DRIVE B0090-004 RUBBER ROLLER 1.1.1 600590...
  • Page 67 REVISION HISTORY Parts List DESCRIPTION DATE ITEM PART NUMBER DESCRIPTION RELEASED 8/5/2015 01079-LH IDLER RELEASE ARM LH 01079-RH IDLER RELEASE ARM RH .01930 KNURLED ROLLER ASSY. 01930-6 KNURLED ROLLER M0030-006 KNURLED ROLLER SHAFT B0030-050 BEARING 1/4 x 7/8 x 9/32 .01920 SHAFT ASSY - IDLER RELEASE M0010-084...
  • Page 68 REVISION HISTORY DESCRIPTION DATE Loctite Application Note: RELEASED 8/4/2015 277 is RED Loctite 242 is BLUE Loctite 538 is GREEN Loctite / is no Loctite applied Parts List ITEM PART NUMBER DESCRIPTION M0035-042 BRAKE POST LABN-0025-4 DANCER BAR WELDMENT 01053 DANCER ROLLER FOR 906 M0030-004 DANCER ROLLER SHAFT...
  • Page 69 REVISION HISTORY DESCRIPTION DATE Parts List RELEASED 1/22/2016 ITEM PART NUMBER DESCRIPTION LABN-0175-4 IDLER ROLLER, ANTI STATIC LABN-0176-3 SHAFT, IDLER ROLLER LABN-0177-3 BRUSH SHAFT LABN-0178-3 BRUSH CLAMP FFNSDP 1/4" FENDER WASHER FFWSDP FLAT WASHER 1/4 FBHSE075S05 BHCS, 1/4-20 x 3/4" FLWSDP LOCK WASHER 1/4 FLWSEP...
  • Page 70 REVISION HISTORY DESCRIPTION DATE RELEASED 1/22/2016 Parts List ITEM PART NUMBER DESCRIPTION MLT80-036 IDLER MOUNT B0010-033 FLANGED BUSHING 08850 IDLER SPROCKET, 25-B-15 FSBSH087B05 SHOULDER BOLT FHHSH075P05 HHCS, 5/16-18 X 0.75 LG FLWSEP LOCK WASHER M8 FFWSEP 5/8" FLAT WASHER Loctite Application Note: LOVESHAW PART # CAD FILE...
  • Page 71 REVISION HISTORY DESCRIPTION DATE RELEASED 8/5/2015 Parts List ITEM PART NUMBER DESCRIPTION MLT80-045 OUTSIDE BEARING CAP MLT80-044 STAND OFF POST MLT80-035 REWIND SPINDLE BUSHING CAP FFHSD062P05 10-32 FHS FSHSD063S05 SOCKET HEAD CAP SCREW 01601 Bearing SKF 16101 B0010-008 BUSHING LABN-0162-4 TAPE RELEASE PIN LABN-0163-4 REWIND SPINDLE...
  • Page 72 REVISION HISTORY DESCRIPTION DATE RELEASED 8/5/2015 1.5.2 1.5.1 Parts List ITEM PART NUMBER DESCRIPTION ----------------- PEAL EDGE ASSY. 01067 WEB GUIDE RAILS 01033 ASSY. DISPENSING BLADE & SHAFT 1.2.1 600736 I STD. 2" DISPENSING BLADE 1.2.2 600262 I DISPENSE BLADE SHAFT 01069 WEB GUIDE POST 14020...
  • Page 73 PNEUMATIC ASSEMBLIES (FOR ALL MODELS)
  • Page 74 REVISION HISTORY Parts List DESCRIPTION DATE DESIGNER APPROVED ITEM PART NUMBER DESCRIPTION 08-192 9/25/08 A.L.S. W.M. 08056-SS SINGLE (1) HOLE AIR TUBE ADDED 3-HOLE 12/21/2009 or 1 08056-SS-3 THREE (3) HOLE AIR TUBE TUBE FSSSD037B05 10-32 X 3/8 SET SCREW P6010-007A FLOW CONTROL ELBOW - METER IN .14018-LT.idw...
  • Page 77 PNEUMATIC DIAGRAM (STRAIGHT TAMP MODELS)
  • Page 79 PNEUMATIC DIAGRAM (DUAL TAMP – SWING ARM MODEL)
  • Page 81 APPLICATOR ASSEMBLIES (STRAIGHT TAMP MODELS)
  • Page 82 REVISION HISTORY DESCRIPTION DATE 10/31/2008 ADDED ITEM 10 04/27/2009 Parts List ITEM PART NUMBER DESCRIPTION P8010-416 TWIN ROD AIR CYLINDER 140LT-046 VACUUM GRID MLT80-042 SENSOR MOUNT PLATE MLT80-033 VACUUM CHAMBER 14030 FITTING FFHSB050B05 FLAT HD.CAP SCREW #8-32 x 1/2 FSHMG020P10 SOC.
  • Page 83 REVISION HISTORY DESCRIPTION DATE NOTE: RIGHT HAND (STANDARD) IMAGE SHOWN. RELEASED 9/4/2009 FOR LEFT HAND - REVERSE PART 3 ON ASSEMBLY. Parts List ** STANDARD CHAMBER AND GRID PLATE SHOWN. ITEM PART NUMBER DESCRIPTION DEPENDING ON THE LABEL SIZE, A CUSTOM GRID P8010-420 AIR CYL.
  • Page 84 APPLICATOR ASSEMBLY (DUAL TAMP – SWING ARM MODEL)
  • Page 85 REVISION HISTORY Parts List DESCRIPTION DATE ITEM PART NUMBER DESCRIPTION RELEASED 10/14/2009 R000-004/BLK__ EXTRUSION, 1" X 3", BLACK LABN-0017-4 MOUNTING PLATE, ROTARY B0020-016 DOUBLE T-NUT, 1/4-20 THREADS FBHSE075P05 BUTTON HEAD, 1/4-20 X 3/4 P8010-405 ROTARY ACTUATOR M0040-049 ACTUATOR BLOCK M0040-050 ACTUATOR STOP BLOCK FSHSE050P05 SOCKET HEAD SCREW, 1/4-20 X 1/2...
  • Page 86 ELECTRICAL ASSEMBLY AND SCHEMATICS FOR (STRAIGHT TAMP DUAL TAMP – SWING ARM MODELS)
  • Page 91 PLC PROGRAM Micro830 PLC (STRAIGHT TAMP MODELS DUAL TAMP – SWING ARM MODELS) (Note: Call Factory for an Electronic Copy of the Program)