Omron KM1 User Manual page 103

Index
Numbers/symbols
3-phase 3-wire.......................2-13, 2-26, 2-27, 2-28
3-phase 4-wire.......................2-13, 2-26, 2-27, 2-28
3-STATE HIGH threshold/3-STATE LOW threshold
......................................................................... 3-20
3-STATE function .................................... 3-17. 3-18
3-STATE target ................................................. 3-18
3-STATE hysteresis .......................................... 3-20
A
Abbreviation ......................................................... IX
PMU1A ............................................................. IX
PMU2A ............................................................. IX
EMU8A ............................................................. IX
PGR1C ............................................................. IX
PVS1C .............................................................. IX
VSU1B .............................................................. IX
VAU1B .............................................................. IX
CTD8E.............................................................. IX
ZCT8E .............................................................. IX
DRT .................................................................. IX
About dedicated CT............................................A-7
Specifications..................................................A-7
External Dimensions (unit: mm)......................A-7
Split type .....................................................A-7
Panel fixed (through) type ...........................A-8
Dedicated CT cable.....................................A-8
Active input setting ........................................... 3-12
Active power....................................................... 3-6
Active power alarm output ................................ 3-13
Alarm history .................................................... 3-12
Alarm output ..................................................... 3-12
Alarm output setting ........................................... 3-9
Alarm parameter setting ..................................... 3-9
Applicable phase wire ........................................ 3-3
Assume based on operation indicator LED ........ 4-3
Assume based on phenomena........................... 4-5
Assume based on the status .............................. 4-4
RAM error ....................................................... 4-4
EEPROM error................................................ 4-4
RTC error........................................................ 4-4
Communication error ...................................... 4-4
Operation mode .............................................. 4-4
Voltage input over ........................................... 4-4
Current input over ........................................... 4-4
Insufficient input voltage ................................. 4-4
Frequency input error ..................................... 4-4
CT input .......................................................... 4-4
Event input...................................................... 4-4
Thermistor input.............................................. 4-4
OUT ................................................................ 4-4
LOW condition ................................................ 4-4
MIDDLE condition........................................... 4-4
HIGH condition ............................................... 4-4
Alarm .............................................................. 4-4
Average count .................................................... 3-5
C
Communication function..................................... 1-5
CompoWay/F ............................................. 1-2,2-28
Connection configuration.................................... 2-3
Connection connector ........................................ 2-8
Consumed power ............................................. 2-25
CT input............................................................ 2-27
CT ratio............................................................... 3-4
CT signal detection............................................. 3-5
Current ............................................................... 3-7
D
Dedicated CT ......................................VII, 2-12, A-7
Dedicated CT cable......................................VII, A-8
Dedicated CT type ............................................. 3-3
Model KM20-CTF-5A...................................... 3-3
Model KM20-CTF-50A.................................... 3-3
Model KM20-CTF-100A.................................. 3-3
Model KM20-CTF-200A.................................. 3-3
Model KM20-CTF-400A.................................. 3-3
Model KM20-CTF-600A.................................. 3-3
Model KM20-CTB-5A/50A .............................. 3-3
Driving USB bus power .................................... 2-26
E
Event input ....................................................... 2-29
Event input function.......................................... 3-16
Event NPN/PNP input mode setting ............. 3-16
Event N-O/N-C input mode setting ............... 3-16
Pulse input count .......................................... 3-17
ON time of pulse enter.................................. 3-17
Function using event input............................ 3-17
Measurement start time/measurement end time
.................................................................. 3-17
Power original unit .................................... 3-17
3-STATE function ...................................... 3-17
Explanation of the display unit............................ 1-7
PWR ............................................................... 1-7
CONN ............................................................. 1-7
ALM ................................................................ 1-7
COMM ............................................................ 1-7
CT................................................................... 1-7
EV................................................................... 1-7
OUT................................................................ 1-7
TH................................................................... 1-7
F
Flow before use.................................................. 2-2
Setting example.............................................. 2-3
Flow of troubleshooting ...................................... 4-2
Format.................................................................. IX
Model KM1-PMU1A-FLK .................................. IX
Model KM1-PMU2A-FLK .................................. IX
Model KM1-EMU8A-FLK .................................. IX
Model KE1-PGR1C-FLK................................... IX
Model KE1-PVS1C-FLK ................................... IX
Model KE1-VSU1B-FLK ................................... IX
Model KE1-VAU1B-FLK.................................... IX
Model KE1-CTD8E ........................................... IX
Model KE1-ZCT8E ........................................... IX
Model KE1-DRT-FLK ........................................ IX
Format standard............................................... 1-13
Frequency .......................................................... 3-7
Function by unit.................................................. 1-3
H
HIGH, MIDDLE, or LOW state integrated time "Ratio"
......................................................................... 3-21
HIGH, MIDDLE, or LOW state integrated power
amount "Ratio" ................................................. 3-21
Horizontally connecting hook ............................. 2-7
I
Inactive power .................................................... 3-7
Inactive power alarm output ............................. 3-15
Indication of voltage ......................................... 2-26
Initialization ...................................................... 3-21
Setting value initialization ............................. 3-21
MAX/MIN initialization................................... 3-21
Measurement history initialization................. 3-21
Alarm history initialization ............................. 3-21