Honda EG3600CX Manual page 35

82Z30000.book 4 ページ ２０１０年６月２５日 金曜日 午後５時５０分
SERVICE INFORMATION
EG5500CX/EG6500CX/EG5500CXS/EG6500CXS
Part
Engine Engine
speed
Cylinder compression
Cylinder Sleeve I.D.
Cylinder head Warpage
Piston Skirt O.D.
Piston-to-cylinder clearance
Piston pin bore I.D.
Piston pin Pin O.D.
Piston pin-to-piston pin bore clearance
Piston rings Ring side
clearance
Ring end gap
Ring width
Connecting rod Small end I.D.
Big end I.D.
Big end oil clearance
Big end side clearance
Crankshaft Crank pin O.D.
Runout
Valves Valve
clearance
Valve
stem O.D.
Valve guide
I.D.
Guide-to-
stem
clearance
Valve seat width
Valve spring free length
Valve spring perpendicularity
Camshaft Camshaft O.D.
Cam height
Cylinder barrel Camshaft holder I.D.
Crankcase
Camshaft holder I.D.
cover
Spark plug Gap
Ignition coil Air gap
Carburetor Main jet
Float height
Pilot screw opening
Starter motor Brush length
(EG5500CXS/
EG6500CXS
Mica depth
only)
2-4
Item
Except EG6500CX
SH/SKH/LDH/LTH type
3,000 ± 100 min
/EG6500CXS
SH/SKH/LDH/LTH type
EG6500CX
SH/SKH/LDH/LTH type
3,600 ± 100 min
/EG6500CXS
SH/SKH/LDH/LTH type
1.37 MPa (14 kgf/cm
at 1,400 min
88.000 – 88.017 (3.4646 – 3.4652)
87.965 – 87.985 (3.4632 – 3.4640)
0.015 – 0.052 (0.0006 – 0.0020)
20.002 – 20.008 (0.7875 – 0.7877)
19.994 – 20.000 (0.7872– 0.7874)
0.002 – 0.014 (0.0001 – 0.0006)
Top 0.030 – 0.060 (0.0012 – 0.0024)
Second 0.030 – 0.060 (0.0012 – 0.0024)
Top 0.200 – 0.350 (0.0079 – 0.0138)
Second 0.350 – 0.500 (0.0138 – 0.0197)
Oil (side rail) 0.20 – 0.70 (0.008 – 0.028)
Top 1.160 – 1.175 (0.0457 – 0.0463)
Second 1.160 – 1.175 (0.0457 – 0.0463)
20.005 – 20.020 (0.7876 – 0.7882)
36.025 – 36.039 (1.4183 – 1.4189)
0.040 – 0.064 (0.0016 – 0.0025)
0.1 – 0.4 (0.004 – 0.016)
35.975 – 35.985 (1.4163 – 1.4167)
IN 0.15 ± 0.02
EX 0.20 ± 0.02
IN 6.575 – 6.590 (0.2589 – 0.2594)
EX 6.535 – 6.550 (0.2573 – 0.2579)
IN/EX 6.600 – 6.612 (0.2598 – 0.2603)
IN 0.010 – 0.037 (0.0004 – 0.0015)
EX 0.050 – 0.077 (0.0020 – 0.0030)
1.0 – 1.2 (0.04 – 0.05)
39.0 (1.54)
15.966 – 15.984 (0.6286 – 0.6293)
IN 32.398 – 32.798 (1.2755 – 1.2913)
EX 31.886 – 32.286 (1.2554 – 1.2711)
16.000 – 16.018 (0.6299 – 0.6306)
16.000 – 16.018 (0.6299 – 0.6306)
0.70 – 0.80 (0.028 – 0.031)
0.2 – 0.6 (0.01 – 0.02)
# 102
13.2 (0.52)
2 – 1/4 turns out
7.0 (0.28)
1.0 (0.04)
Standard Service limit
-1
(rpm)
-1 (rpm)
2
, 199 psi)
-1 (rpm)
88.17 (3.471)
– 0.10 (0.004)
87.85 (3.459)
0.12 (0.005)
20.042 (0.7891)
19.950 (0.7854)
0.08 (0.003)
0.15 (0.006)
0.15 (0.006)
1.0 (0.04)
1.0 (0.04)
1.0 (0.04)
1.150 (0.0453)
1.150 (0.0453)
20.07 (0.790)
36.07 (1.420)
0.12 (0.005)
1.0 (0.04)
35.93 (1.415)
– 0.1 (0.004)
6.44 (0.254)
6.40 (0.252)
6.66 (0.262)
0.11 (0.004)
0.13 (0.005)
2.1 (0.08)
37.5 (1.48)
–
15.92 (0.627)
32.10 (1.264)
31.59 (1.244)
16.05 (0.632)
16.05 (0.632)
3.5 (0.14)
0.2 (0.01)
Unit: mm (in)
–
–
–
–
1.5°
–
–
–
–
–