Table 2-2. Owners Annual Inspection Record; Table 2-3. Tire Specifications; Table 2-4. Maximum Platform Capacities - Skyjack SJKB-40-D Operating Manual

ANSI/SIA (United States)
You are required by ANSI/SIA A92.5 -1992 to read and understand YOUR RESPONSIBILITIES in the Manual Of
Responsibilities before you use or operate this work platform.
CSA (Canada) and CE (Europe)
You are required to conform to national health and safety regulations applicable to the operation of this work platform.
FAILURE TO COMPLY with your REQUIRED RESPONSIBILITIES in the use and operation of the work platform
could result in death or serious injury.
OPERATOR SAFETY REMINDERS
The National Safety Council reminds us that most accidents are caused by the failure of some individuals to follow
simple and fundamental safety rules and precautions. Common sense dictates the use of protective clothing when
working on or near machinery. Use appropriate safety devices to protect your eyes, ears, hands, feet and body.
You, as a careful operator, are the best insurance against an accident. Therefore, proper usage of this work platform
is mandatory. The following pages of this manual should be read and understood completely before operating the
work platform. Any modifications from the original design are strictly forbidden without written permission from
SKYJACK, Inc.
DANGER VOLTAGE RANGE
ELECTROCUTION HAZARD
(PHASE TO PHASE)
THIS MACHINE IS NOT INSULATED.
MAINTAIN SAFE CLEARANCES FROM
(Over 300V to 50KV)
ELECTRICAL POWER LINES AND
APPARATUS. YOU MUST ALLOW FOR (Over 50KV to 200KV)
PLATFORM SWAY, ROCK OR SAG. THIS
(Over 200KV to 350KV)
WORK PLATFORM DOES NOT PROVIDE
PROTECTION FROM CONTACT WITH OR (Over 350KV to 500KV)
PROXIMITY TO AN ELECTRICALLY
(Over 500KV to 750KV)
CHARGED CON-DUCTOR.
(Over 750KV to 1000KV)
FAILURE TO AVOID THIS HAZARD WILL RESULT IN DEATH OR SERIOUS INJURY!
Page ii
JUN. 1999
WARNING
MINIMUM SAFE APPROACH DISTANCE
(METERS)
(FEET)
(0 TO 300V)
AVOID CONTACT
10 3.05
4.60
15
6.10
20
7.62
25
35 10.67
45 13.72
SJKB-40-D, SJKB-40-D/F
BRAKE OPERATION TEST PROCEDURE
Proper operation of the parking brakes should be checked daily or at the beginning of each shift. Locate the machine
in an appropriate area for testing the brakes. IMPORTANT NOTE: The area for testing the machine MUST be completely
level and free of obstructions. DO NOT drive on an incline unless the parking brakes are working properly. With the
machine fully stowed and the throttle switch in the high position (if engine powered). Drive the machine forward at full
speed and remove foot from foot switch. Repeat this step driving in reverse.
Parking brakes will instantly engage causing the machine to stop immediately.
The machine should come to an instant and abrupt stop. If the machine does not stop instantly or if the machine pulls
to one side while stopping, the brake adjustment MUST be checked before putting the machine into service.

Table 2-2. Owners Annual Inspection Record

MODEL NUMBER___________________________ SERIAL NUMBER______________
RECORDING
DATE
RECORDING
1 2 3
YEAR #
OWNERS NAME
INSPECTED
BY

Table 2-3. Tire Specifications

Tire
Model
Size
STANDARD 30 x 10.00 x 16.5
FOAM FILLED
30 x 10.00 x 16.5
(Option)
* 28 Durometer Fill installed at 55 psi.

Table 2-4. Maximum Platform Capacities

Model
SJKB-40-D, SJKB-40-D/F
NOTE: Refer to capacity label on work platform for additional information.
RECOMMENDED HYDRAULIC OILS
DO NOT use synthetic or fire resistant oil in this work platform. Use ATF Dexron III (ESSO) or equivalent hydraulic oil.
For conditions causing oil temperatures below -31°F (-35° C) and above 122°F (50° C) consult Skyjack, Inc.
RECOMMENDED AXLE LUBRICANT
TWO WHEEL DRIVE: SAE 80W90 GL-5 gear oil.
FOUR WHEEL DRIVE: Sunoco duragear (synthetic) SAE 75W90 gear oil or equivelant.
SJKB-40-D, SJKB-40-D/F
WARNING
4 5 6 7
Fill Specification
Rating Type
10 Ply Air
10 Ply Solid Urethane
Platform Capacity (unrestricted)
500# (227kg) 2 occupants
JUN. 1999
SECTION 2, Page 11
8
Mt40c-202
Pressure
55 psi
*
Mt40c-201
Mt40c-203