Operator Qualifications; Operator Responsibility For Maintenance; Maintenance And Inspection Schedule; Owner's Annual Inspection Record - Skyjack SJKB-40-D Operating Manual

Turret Transportation Lock
1
2
Ma40-204
Figure 2-4. Turret Transportation Lock
1. TURRET TRANSPORTATION LOCK
2. TURRET TRANSPORTATION LOCK
RETAINING PIN
1. TURRET TRANSPORTATION LOCK - This locking
device, located on the turret base plate near the rotation
gear, is used to lock the turret in place during shipping
only.
2. TURRET TRANSPORTATION LOCK RETAINING
PIN - This retaining pin is used to hold the transportation
lock in either the locked or unlocked position.

Base Controls - Hydraulic

Emergency Lowering Valves
Ma40-205
Ma40-206
1
2
Figure 2-5. Emergency Lowering Valves and Procedure
Label
1. EMERGENCY LOWERING VALVE ON BOOM
2. EMERGENCY LOWERING VALVE ON JIB
1. EMERGENCY LOWERING VALVE ON BOOM -
Located at the base on the boom cylinder, this valve
allows boom lowering in the event of an emergency or
an electrical system failure. Turning the valve knob
counterclockwise allows the boom to gradually lower.
JUN. 1999
SECTION 2, Page 4
Valve MUST be fully closed (clockwise) to restore normal
operation.
2. EMERGENCY LOWERING VALVE ON JIB -
Located at the base on the jib cylinder, this valve allows
boom lowering in the event of an emergency or an
electrical system failure. Turning the valve knob
counterclockwise allows the jib to gradually lower. Valve
MUST be fully closed (clockwise) to restore normal
operation.
NOTE
For European models only, the manual lowering
valve knobs are located inside engine cabinet bi-fold
door on turret.
Drive Relief Valve Overrides
1
Ma40-207
Figure 2-6. Drive Pump
1. DRIVE RELIEF VALVE WITH OVERRIDE STEM
1. DRIVE RELIEF VALVE WITH OVERRIDE STEM.
The relief override stems, located on the top and bottom
of the Drive Pump, are used to override the drive relief
valves allowing the machine to be loaded or unloaded
from a trailer using a winch line. To override the drive
relief valve the procedure below MUST be followed:
DANGER
DO NOT attempt to override the relief valves without the
wheels chocked.
Step 1. Place the machine on a flat level surface and
chock the wheels to prevent from rolling.
Step 2. Loosen the retaining nut on the relief valve
override stem. Screw in the override stem
(clockwise) until it stops. Repeat this step for
both relief valves.
Step 3. Release the parking brake (see Brake Manifold
in this section). The machine is now ready to be
loaded or unloaded using a winch line.
SJKB-40-D, SJKB-40-D/F
SECTION 2
OPERATOR CONTROLS/INSPECTIONS

OPERATOR QUALIFICATIONS

Only trained and authorized persons should use this work platform. Safe use of this work platform requires the operator
to understand the limitations and warnings, operating procedures and operator's responsibility for maintenance.
Accordingly, the operator MUST understand and be familiar with this operating manual, its warnings and instructions
and ALL warnings and instructions on the work platform. Operator also MUST be familiar with employer's work rules
and related government regulations and be able to demonstrate his/her ability to understand and operate THIS make
and model work platform in the presence of a qualified person.
OPERATOR'S RESPONSIBILITY FOR MAINTENANCE
Death or injury can result if the work platform is not kept in good working order. Inspection and maintenance should be
performed by competent personnel who are familiar with mechanical procedures.
The operator should be assured that the work platform has been properly maintained and inspected before using it.
Even if the operator is not directly responsible for the maintenance of this work platform, the operator should perform
ALL the daily inspections found in Table 2-1. Maintenance and Inspection Schedule.
Replace all worn or damaged parts or labels discovered during this inspection.

MAINTENANCE AND INSPECTION SCHEDULE

The actual operating environment of the work platform governs the use of the maintenance schedule. The inspection
points covered in Table 2-1. Maintenance and Inspection Schedule indicates the areas of the work platform to be
maintained or inspected and at what intervals the maintenance and inspections are to be performed.

OWNER'S ANNUAL INSPECTION RECORD

It is the responsibility of the owner to arrange daily, weekly, monthly and annual inspections of the work platform.
(Refer to Table 2-2. in this manual.)

GENERAL MAINTENANCE HINTS

• Before attempting any repair work, disconnect the battery by turning the Battery Disconnect Switch to the
"OFF" position.
• Preventative maintenance is the easiest and least expensive type of maintenance.

OPERATING CONTROL IDENTIFICATION

The following descriptions are for identification, explanation and locating purposes only. A qualified operator MUST
read and completely understand these descriptions before operating this work platform. Procedures for operating this
work platform are detailed in the "OPERATING PROCEDURES'' section on Pages 7 through 9 in this manual.
SJKB-40-D, SJKB-40-D/F
NOTE
JUN. 1999
SECTION 2, Page 1
2