EdilKamin IDROSALLY Installation, Use And Maintenance Manual page 52

Pellet-loading adjustment: (with self-regulation deactivated).
Press and hold the menu key for two seconds to gain access to
the language menu, use the + key to nd the "ADJ PELLET"
menu, con¬ rm the menu with the M key, and the message
"PELLET ADJ 00%" will appear on the display.
The pellet drop can be adjusted manually by changing the
capacity in percentage terms (+/- 30 %).
By con rming this function with the menu key, you can access
the function to adjust pellet loading. By decreasing the
value set, pellet loading is decreased. By increasing the value
set, pellet loading increases. This function is useful if
changing the pellet type for which the stove has been calibrated
and loading therefore needs correcting.
Should this correction not suf ce, contact the Edilkamin-autho-
rised Dealer, to establish the new operating axis.
Notes on ame variability
Flame status may vary depending on the type of pellet used,
in addition to normal solid fuel ame variability and regular
combustion chamber cleaning carried out automatically by the
boiler.
(N.B.: which does NOT replace necessary cold suction by the
user prior to ignition).
RESERVE WARNING
The boiler-stove is tted with an electronic function that de-
tects the residual quantity of pellets in the tank.
The detection system is integrated into the electronic board,
allowing you to see how many hours and kg are left until
pellet exhaustion, at all times. For correct system function, it is
important that the following procedure is followed during the
rst ignition (by the Dealer).
This provides a reference indicator.
Greater precision is obtained by regularly zeroing the system
before lling it again. Edilkamin does not accept any responsi-
bility for differences from what is indicated (which may be due
to external factors).
Pellet reserve system
Before enabling the system, you need to load a sack of pellets
into the tank and use the stove until the loaded
fuel has run out. This allows for a short system road test.
After this, the tank can be lled completely and the stove
started up.
When running, at the time at which a whole 15 kg sack of
pellets can be loaded, the display will show the word "Reserve"
ashing.
At this point, after having poured in a sack of pellets, you need
to 'inform' the memory that you have loaded 15 kg.
To do so, proceed as follows:
1. press the "M" key (for approximately 3-4 seconds) until the
word "LANGUAGE" appears.
2. press the "+" key until the word "Reserve pellet" appears.
3. press the "M" key until the following screen appears,
INSTRUCTIONS FOR USE
- 52
Kg remaining in tank
then use the "+" key to take the gure (*) to the value equal to
the Kg of pellets loaded (15 kg in the above example).
4. press the "M" key to con rm
5. press the key to exit.
After having completed the above procedure, after having con-
sumed the 15 kg, the wording "Reserve" will appear ashing at
intervals.
The operation can then be repeated, proceeding from point 1 to
point 5, every time you wish to load pellets (optional).
EMERGENCY BUTTON
If the radio remote control device does not work, you can carry
out the basic functions by means of a red emergency button
positioned on the back of the stove (see Fig. 1).
Push this button once or more times to activate the required
function:
1. BOILER-STOVE OFF
by pressing the red button for 2 seconds this turns on.
2. BOILER-STOVE ON
by pressing the red button for 2 seconds this turns off.
3. BOILER-STOVE ON
manual mode, by pressing the red button, you go from P1 to
P3.
4. BOILER-STOVE ON
If the stove is set in power mode, press it quickly to change the
SET output, increa¬sing it cyclically from 50 to 80°C; if se¬t
in "comfort clima", the desired environmental temperature can
be increased cyclically from 10 to 30°C
emergency button
g. 1
-
Kg loaded