SpectraLink NetLink MOG600 Installation Manual
Open applications interface
Hide thumbs
Also See for NetLink MOG600:
- Technical bulletin (3 pages) ,
- Installation and administration (35 pages) ,
- Installation manual (14 pages)
Subscribe to Our Youtube Channel
Related Manuals for SpectraLink NetLink MOG600
Summary of Contents for SpectraLink NetLink MOG600
- Page 1 Installation NetLink Open Applications Interface (OAI) Gateway Part Number: 72-0078-07 Issue A...
- Page 2 No representation or other affirmation of fact contained in this document including but not limited to statements regarding capacity, response-time performance, suitability for use, or performance of products described herein shall be deemed to be a warranty by SpectraLink for any purpose, or give rise to any liability of SpectraLink whatsoever.
- Page 3 IEC 801-3 RF Radiated IEC 801-4 Fast Transients Additionally, all models comply to EN60950/ IEC950 with CB certificates & reports. February 21, 2002 Mark R. Angliss, Manager; Quality & Process Engineering, For the SpectraLink Corporation Part Number: 72-0078-07-A.doc Page 3...
- Page 4 Note concerning shielded cable: SpectraLink recommends the use of shielded cable for all external signal connections in order to maintain FCC Part 15 emissions requirements. Note concerning the Wireless Telephones: This device complies with Part 15 of the FCC Rules.
- Page 5 If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. If you experience trouble with this telephone equipment, please contact SpectraLink Corporation for information on obtaining service or repairs.
- Page 6 SpectraLink Corporation Installation NetLink OAI Gateway Industry Canada (IC) Notice Notice: The Industry Canada (IC) label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational, and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The department does not guarantee the equipment will operate to the user’s satisfaction.
-
Page 7: Table Of Contents
SpectraLink Corporation Installation NetLink OAI Gateway Table of Contents 1. ABOUT THIS DOCUMENT Contacting SpectraLink Icons and Conventions Installation Overview 2. THE NETLINK OAI GATEWAY System Overview The NetLink OAI Gateway Front Panel 3. INSTALL THE NETLINK OAI GATEWAY Perform Initial Test Assign the NetLink OAI Gateway’s IP Address... - Page 8 SpectraLink Corporation Installation NetLink OAI Gateway 8. CERTIFICATION TEST 9. SOFTWARE MAINTENANCE Software Updates for MOG700 Systems TFTP Software Updates for MOG600 Systems 10. WIRELESS DEVICE PLANNING WORKSHEET Part Number: 72-0078-07-A.doc Page 8...
-
Page 9: About This Document
(LAN) or RS-232 port. The installation process connects the NetLink OAI Gateway to an existing LAN. Contacting SpectraLink SpectraLink wants you to have a successful installation. If you have questions please contact our The Hotline is open Monday Customer Support Hotline at (800) 775-5330. -
Page 10: The Netlink Oai Gateway
SpectraLink Corporation Installation NetLink OAI Gateway 2. The NetLink OAI Gateway The NetLink OAI Gateway enables third-party applications to communicate directly with up to 10,000 NetLink Wireless Telephones, allowing users to retrieve and respond to information using their Wireless Telephones. -
Page 11: System Overview
Paging Controller, Nurse Call Systems, Industrial Controllers (See Application Note for Specific Installation) Ethernet cable Device supplied by Phone cabling SpectraLink RS-232 cable * Note that the wired telephone system may include a NetLink Telephony Gateway Supplied by SpectraLink Part Number: 72-0078-07-A.doc Page 11... -
Page 12: The Netlink Oai Gateway Front Panel
SpectraLink Corporation Installation NetLink OAI Gateway The NetLink OAI Gateway Front Panel There are two different models with similar front panel indicators – Network Link LEDs – lit when there is a network connection, i.e. LINK OK. (L)NKOK – lit if there is system activity. -
Page 13: Install The Netlink Oai Gateway
1. Connect the power plug from the NetLink OAI Gateway’s power adapter to the power jack on the front (or rear) of the Gateway box. Use only the adapter ordered from SpectraLink. 2. Plug the power adapter into an outlet or outlet strip. -
Page 14: Assign The Netlink Oai Gateway's Ip Address
SpectraLink Corporation Installation NetLink OAI Gateway Assign the NetLink OAI Gateway’s IP Address You can administer the NetLink OAI Gateway via Telnet connection from the NetLink Administration Console. However, as with the Telephony Gateways, the NetLink OAI Gateway must be assigned an IP address before you can connect using Telnet. -
Page 15: Connect The Netlink Oai Gateway To The Lan
SpectraLink Corporation Installation NetLink OAI Gateway The procedure for entering/changing the IP address of the NetLink OAI Gateway is described below in section 4.2. When the NetLink OAI Gateway has been configured, disconnect the terminal or PC from the serial port, reconnect the communication cable between the NetLink OAI Gateway and the application server, and reset the system. -
Page 16: Connect The Netlink Oai Gateway To Application Server Via The Lan
SpectraLink Corporation Installation NetLink OAI Gateway Connect the NetLink OAI Gateway to Application Server via the LAN Some applications or systems may require a LAN connection between the application server and the NetLink OAI Gateway. If your applications do not require a LAN connection, you may use the RS-232. -
Page 17: The Main Menu
SpectraLink Corporation Installation NetLink OAI Gateway 4. The Main Menu To connect to the NetLink OAI Gateway, select the host name or IP address of the Gateway from the screen. Gateway Connection Selection menu displays: NetLink OAI System NetLink OAI System Main Menu TFTP Server Download Configuration * This is the default main menu of the OAI Administration console. -
Page 18: Ip Systems Main Menu
SpectraLink Corporation Installation NetLink OAI Gateway IP Systems Main Menu One the configuration procedure is completed; the IP System menu adds a Feature Programming option. Additionally, the OAI Line Configuration option is replaced by a Telephone Line Configuration option. Part Number: 72-0078-07-A.doc... -
Page 19: Configuration Procedures
SpectraLink Corporation Installation NetLink OAI Gateway 5. Configuration Procedures The OAI Gateway must be configured according to the type of system in use: NetLink Telephony Gateway system or IP system. If the NetLink OAI Gateway is being used in an IP phone system, the configuration proceeds independently of the IP system. If the system is using one or more NetLink Telephony Gateways, the OAI Gateway will communicate with them during configuration and operation. -
Page 20: Oai Box Configuration
SpectraLink Corporation Installation NetLink OAI Gateway OAI Box Configuration From the menu, select . The following NetLink OAI System OAI Box Configuration screen displays. ** Option appears only on MOG6xx model. * Option appears only on NetLink Telephony Gateway systems (when “Use NetLink GW with mogX00”... -
Page 21: Network Configuration
SpectraLink Corporation Installation NetLink OAI Gateway Network Configuration From the menu, select . A screen similar NetLink OAI System Network Configuration to the following displays: * Allow FTP Connections option appears on MOG 7xx model only Enter configuration information for the NetLink OAI Gateway. Your LAN administrator should provide this information. - Page 22 SpectraLink Corporation Installation NetLink OAI Gateway • – enter Y (yes) to allow connection to the Allow Telnet Connections NetLink OAI Gateway via Telnet; enter N (no) if you do not want to allow Telnet connection. • – Yes/No * (MOG 7xx only) Allow FTP Connections •...
-
Page 23: Oai Line Configuration
SpectraLink Corporation Installation NetLink OAI Gateway OAI Line Configuration In a NetLink Telephony Gateway system, each telephone line using OAI must be associated with the line and port of its NetLink Telephony Gateway. This procedure tells the OAI Gateway which Wireless Telephone lines are associated with each NetLink Telephony Gateway. -
Page 24: Telephone Line Configuration
SpectraLink Corporation Installation NetLink OAI Gateway Telephone Line Configuration In an IP system, each Wireless Telephone that is to use OAI features must be configured with its line number and MAC address. Optionally the name and extension number of the Wireless Telephone user may be entered. -
Page 25: Deleting A Wireless Telephone
SpectraLink Corporation Installation NetLink OAI Gateway 2. Write the MAC address on the Wireless Planning Device Worksheet. 3. Repeat steps 2, 3, and 4 for each Wireless Telephone to be added or changed. 4. Press Esc to return to the menu. -
Page 26: Feature Programming
SpectraLink Corporation Installation NetLink OAI Gateway Feature Programming The OAI function is accessed in the Wireless Telephone by pressing the button plus a second button. In IP systems, the button used to access the OAI feature from the Wireless Telephone is configured through the Feature Programming option. -
Page 27: Set Or Change Password
NetLink Gateways in the system. Using this option overrides any password already established on the NetLink Telephony Gateways. The default password is admin. Follow the prompts to set a new password. If you forget a password, call SpectraLink Customer Service for assistance. Part Number: 72-0078-07-A.doc Page 27... -
Page 28: System Status Menu
SpectraLink Corporation Installation NetLink OAI Gateway 7. System Status Menu To view the status of the system, select the option from the System Status Menu menu. NetLink OAI System Telephone Line Status * Telephone Line Status option appears only on IP systems. -
Page 29: Network Status
SpectraLink Corporation Installation NetLink OAI Gateway Network Status The NetLink OAI Gateway is connected to the Ethernet network, referred to as the LAN or Local Area Network. The information about that connection is provided through the screen. Network Status From the , select . - Page 30 – number of packets and bytes received addressed to the NetLink OAI Gateway. – the number of broadcast packets and bytes received. RX Broadcast – the number of packets and bytes received with the SpectraLink multicast RX Multicast address. (A “multicast” message is sent to more than one destination on the network.) –...
-
Page 31: Telephone Line Status
SpectraLink Corporation Installation NetLink OAI Gateway Telephone Line Status In IP systems, the screen allows you to see which phones are Telephone Line Status actively communicating with the OAI gateway. From the , select . The NetLink OAI System Status Menu Telephone Line Status Gateway displays up to 16 lines. -
Page 32: Software Versions
SpectraLink Corporation Installation NetLink OAI Gateway Software Versions Each NetLink OAI Gateway and Wireless Telephone runs SpectraLink’s proprietary software that is controlled and maintained through versioning. The Software Version screen provides information about the version currently running on the components. This... -
Page 33: Certification Test
SpectraLink Corporation Installation NetLink OAI Gateway 8. Certification Test When the NetLink OAI Gateway is properly connected to the application server, LED 1 will blink. To test the Wireless Telephones: • If this is a new installation, continue with Wireless Telephone registration and PBX programming, and perform the usual voice and coverage tests when Wireless Telephone installation is complete. -
Page 34: Software Maintenance
(for example, downloading from a web site). Software Updates for MOG700 Systems After software updates are obtained from SpectraLink, they must be transferred to the appropriate location in the LAN to update the code used by the corresponding component. - Page 35 SpectraLink Corporation Installation NetLink OAI Gateway FTP Procedure When using FTP, you use a host system to connect to a remote system. In this example, the host is the client and the server is the OAI Gateway. The “put” command means to copy the files from the host to the remote system.
-
Page 36: Tftp Software Updates For Mog600 Systems
Obtain and load a TFTP server on a LAN connected system. Consult your server vendor’s documentation for information about TFTP. Once the update is obtained from SpectraLink, load it in a location that is accessible by the TFTP program. To configure the host and start the download, select the... -
Page 37: Wireless Device Planning Worksheet
SpectraLink Corporation Installation NetLink OAI Gateway 10. Wireless Device Planning Worksheet Copy and complete this worksheet to track parameters for each NetLink Wireless Telephone. Dialing MAC Address User Name IP Address Ext. Port Part Number: 72-0078-07-A.doc Page 37...
Need help?
Do you have a question about the NetLink MOG600 and is the answer not in the manual?
Questions and answers