Related Manuals for SpectraLink MOG710
Summary of Contents for SpectraLink MOG710
- Page 1 Installation and Administration NetLink Open Applications Interface (OAI) Gateway Part Number: 72-0078-07 Issue B...
-
Page 2: Trademark Information
No representation or other affirmation of fact contained in this document including but not limited to statements regarding capacity, response-time performance, suitability for use, or performance of products described herein shall be deemed to be a warranty by SpectraLink for any purpose, or give rise to any liability of SpectraLink whatsoever. -
Page 3: Important Safety Information
Note concerning shielded cable: SpectraLink recommends the use of shielded cable for all external signal connections in order to maintain FCC Part 15 emissions requirements. Note concerning the NetLink Wireless Telephones: This device complies with Part 15 of the FCC Rules. -
Page 4: Fcc Information
If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. If you experience trouble with this telephone equipment, please contact SpectraLink Corporation for information on obtaining service or repairs. - Page 5 SpectraLink Corporation Installation and Administration NetLink OAI Gateway Industry Canada (IC) Notice Notice: The Industry Canada (IC) label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational, and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The department does not guarantee the equipment will operate to the user’s satisfaction.
-
Page 6: Table Of Contents
SpectraLink Corporation 1. About This Document Related Documents Customer Support Hotline Icons and Conventions 2. The NetLink OAI Gateway System Overview The NetLink OAI Gateway Front Panel 3. Install the NetLink OAI Gateway Perform Initial Test Assign the NetLink OAI Gateway’s IP Address... -
Page 7: About This Document
Available at http://www.spectralink.com/consumer/resources/manuals.jsp. Customer Support Hotline SpectraLink wants you to have a successful installation. If you have questions please contact our Customer Support Hotline at (800) 775-5330. The hotline is open Monday through Friday, 6 a.m. to 6 p.m. Mountain time. -
Page 8: The Netlink Oai Gateway
SpectraLink Corporation The NetLink OAI Gateway The NetLink OAI Gateway enables third-party applications to communicate directly with up to 10,000 NetLink Wireless Telephones, allowing users to retrieve and respond to information using their handsets. The NetLink OAI Gateway is available in two models and several scaled capacity levels, please be sure that the OAI Gateway being configured has the appropriate capacity for your implementation. -
Page 9: System Overview
Wireless Data Device Device supplied by SpectraLink * Note that the wired telephone system may include a NetLink Telephony Gateway Supplied by SpectraLink PN: 72-0078-07-B.doc Installation and Administration Party Applications: Backbone Ethernet switch NetLink OAI Gateway OAI protocol RS 232... -
Page 10: The Netlink Oai Gateway Front Panel
SpectraLink Corporation The NetLink OAI Gateway Front Panel There are two different models with similar front panel indicators Network Link LEDs: Lit when there is a network connection, i.e. LINK OK. (L)NKOK Lit if there is system activity. (A)CT Lit if there are network collisions. -
Page 11: Install The Netlink Oai Gateway
1. Connect the power plug from the NetLink OAI Gateway’s power adapter to the power jack on the front (or rear) of the Gateway box. Use only the adapter ordered from SpectraLink. 2. Plug the power adapter into an outlet or outlet strip. - Page 12 SpectraLink Corporation 1. Connect a terminal or PC to the Gateway’s serial port using a cable that conforms to RS-232 standards for DTE to DTE connections (known as a null modem cable). 2. Reset the system. The following OAI command will display on the terminal: 04830130 3.
-
Page 13: Connect The Netlink Oai Gateway To The Lan
SpectraLink Corporation Connect the NetLink OAI Gateway to the LAN 1. Using an RJ-45 cable, connect the connecting port on the Ethernet switch. 2. Power up the entire system. Any components should go through their usual diagnostic routine. Connect the NetLink OAI Gateway Application Server via RS-232 port Some applications or systems may require an RS-232 connection between the application server and the NetLink OAI Gateway. -
Page 14: Connect The Netlink Oai Gateway To Application Server Via The Lan
SpectraLink Corporation Connect the NetLink OAI Gateway to Application Server via the LAN Some applications or systems may require a LAN connection between the application server and the NetLink OAI Gateway. If your applications do not require a LAN connection, you may use the RS-232. -
Page 15: The Main Menu
SpectraLink Corporation The Main Menu To connect to the NetLink OAI Gateway, select the host name or IP address of the Gateway from the Gateway Connection Selection NetLink OAI System NetLink OAI System Main Menu TFTP Server Download Configuration * This is the default main menu of the OAI Administration console. -
Page 16: Ip Systems Main Menu
SpectraLink Corporation IP Systems Main Menu One the configuration procedure is completed; the IP System menu adds a option. Additionally, the Programming Telephone Line Configuration PN: 72-0078-07-B.doc OAI Line Configuration option. Installation and Administration NetLink OAI Gateway Feature option is replaced by a... -
Page 17: Configuration Procedures
SpectraLink Corporation Configuration Procedures The OAI Gateway must be configured according to the type of system in use: NetLink Telephony Gateway system or IP system. If the NetLink OAI Gateway is being used in an IP phone system, the configuration proceeds independently of the IP system. -
Page 18: Oai Box Configuration
SpectraLink Corporation OAI Box Configuration From the NetLink OAI System displays. ** Option appears only on MOG6xx model. * Option appears only on NetLink Telephony Gateway systems (when is set to GW with mogX00 Enter configuration information for the NetLink OAI Gateway. Your LAN administrator should provide this information. -
Page 19: Network Configuration
You cannot enter spaces in this field. • Subnet Mask Enter the subnet mask defined by the Network Administrator. • Default Router DHCP or static IP address PN: 72-0078-07-B.doc , all system NetLink Telephony... - Page 20 SpectraLink Corporation • Allow Telnet Connections Enter OAI Gateway via Telnet; enter connection. • Allow FTP Connections • DNS server and DNS domain These settings are used to configure Domain Name services. Consult your system administrator for the correct settings. These can also be set to DHCP.
-
Page 21: Oai Line Configuration
SpectraLink Corporation OAI Line Configuration In a NetLink Telephony Gateway system, each telephone line using OAI must be associated with the line and port of its NetLink Telephony Gateway. This procedure tells the OAI Gateway which handset lines are associated with each NetLink Telephony Gateway. -
Page 22: Telephone Line Configuration
SpectraLink Corporation Telephone Line Configuration In an IP system, each handset that is to use OAI features must be configured with its line number and MAC address. Optionally the name and extension number of the handset user may be entered. -
Page 23: Deleting A Handset
SpectraLink Corporation Press Esc to return to the A handset may be associated with one and only one telephone line. The same MAC address may not be assigned to two or more telephone lines. The handset requires special setup which may include setting options on the DHCP server or on the handset to allow it to communicate with the NetLink OAI Gateway. - Page 24 SpectraLink Corporation Navigate to the NetLink OAI System . A screen similar to the following displays: Feature Programming Use the arrow keys to select the function number to associate with OAI and type any label up to six characters. What you type here will be displayed on the handset menu.
-
Page 25: Set Or Change Password
NetLink Telephony Gateways. The default password is Follow the prompts to set a new password. If you forget a password, call SpectraLink Customer Service for assistance. PN: 72-0078-07-B.doc Change Password admin Installation and Administration... -
Page 26: System Status Menu
SpectraLink Corporation System Status Menu To view the status of the system, select the menu. NetLink OAI System * Telephone Line Status option appears only on IP systems. Telephone Line Status Additional information on NetLink Telephony Gateway: Configuration and Administration. -
Page 27: Network Status
SpectraLink Corporation Network Status The NetLink OAI Gateway is connected to the Ethernet network, referred to as the LAN or Local Area Network. The information about that connection is provided through the Network Status From the System Status Menu about the Ethernet network. This information can help troubleshoot network problems. - Page 28 SpectraLink Corporation RX Broadcast The number of broadcast packets and bytes received. RX Multicast The number of packets and bytes received with the SpectraLink multicast address. (A “multicast” message is sent to more than one destination on the network.) RX Not For Us The number of multicast packets and bytes received that were not for the NetLink OAI Gateway.
-
Page 29: Telephone Line Status
SpectraLink Corporation Telephone Line Status In IP systems, the Telephone Line Status actively communicating with the OAI gateway. From the System Status Menu Gateway displays up to 16 lines. A sample screen is displayed here. Move to the next group of 16 by using the arrow keys. -
Page 30: Software Versions
SpectraLink Corporation Software Versions Each NetLink OAI Gateway and handset runs SpectraLink’s proprietary software that is controlled and maintained through versioning. The provides information about the version currently running on the components. This information will help you determine if you are running the most recent version and will assist SpectraLink engineering and/or customer support in troubleshooting software problems. -
Page 31: Certification Test
SpectraLink Corporation Certification Test When the NetLink OAI Gateway is properly connected to the application server, will blink. LED 1 To test the handsets: • If this is a new installation, continue with handset registration and PBX programming, and perform the usual voice and coverage tests when handset installation is complete. -
Page 32: Software Maintenance
The redundant phone list configuration. The fnctla.bin file is upgraded periodically by SpectraLink engineering and is the only file that you will download. The other files are configuration files and their names are provided here for your information and backing up purposes. - Page 33 SpectraLink Corporation FTP Procedure When using FTP, you use a host system to connect to a remote system. In this example, the host is the client and the server is the OAI Gateway. The “put” command means to copy the files from the host to the remote system. The “get”...
-
Page 34: Tftp Software Updates For Mog600 Systems
Obtain and load a TFTP server on a LAN connected system. Consult your server vendor’s documentation for information about TFTP. Once the update is obtained from SpectraLink, load it in a location that is accessible by the TFTP program. To configure the host and start the download, select the... -
Page 35: 10. Wireless Device Planning Worksheet
SpectraLink Corporation 10. Wireless Device Planning Worksheet Copy and complete this worksheet to track parameters for each NetLink Wireless Telephone. OAI Port MAC Address PN: 72-0078-07-B.doc Installation and Administration User Name Dialing Ext. NetLink OAI Gateway IP Address Page 35...
Need help?
Do you have a question about the MOG710 and is the answer not in the manual?
Questions and answers