Related Manuals for SpectraLink Wireless@work MOG500
Summary of Contents for SpectraLink Wireless@work MOG500
- Page 1 Open Applications Interface (OAI) Gateway Installation and Setup Link Wireless Telephone System Link 150 MCU Part Number: 72-0075-07 Issue B...
- Page 2 No representation or other affirmation of fact contained in this document including but not limited to statements regarding capacity, response-time performance, suitability for use, or performance of products described herein shall be deemed to be a warranty by SpectraLink for any purpose, or give rise to any liability of SpectraLink whatsoever.
- Page 3 Note concerning shielded cable: SpectraLink recommends the use of shielded cable for all external signal connections in order to maintain FCC Part 15 emissions requirements. Note concerning the Wireless Telephone and Base Stations: This device complies with Part 15 of the FCC Rules.
- Page 4 If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. If you experience trouble with this telephone equipment, please contact SpectraLink Corporation for information on obtaining service or repairs.
- Page 5 SpectraLink Corporation Open Application Interface Gateway Installation and Setup Link WTS – Link 150 MCU Industry Canada (IC) Notice Notice: The Industry Canada (IC) label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational, and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s).
-
Page 6: Table Of Contents
SpectraLink Corporation Open Application Interface Gateway Installation and Setup Link WTS – Link 150 MCU Table of Contents 1. ABOUT THIS DOCUMENT Contacting SpectraLink Icons and Conventions Installation Overview 2. OAI OVERVIEW System Diagram The OAI Gateway’s Front Panel 3. INSTALLING THE OAI GATEWAY... -
Page 7: About This Document
(MOG 500) by SpectraLink Corporation. The installation process connects the OAI Gateway to an existing Link 150 MCU. Contacting SpectraLink SpectraLink wants you to have a successful installation. If you have questions please contact our The Hotline is open Monday Customer Support Hotline at (800) 775-5330. -
Page 8: Oai Overview
SpectraLink Corporation Open Application Interface Gateway Installation and Setup Link WTS – Link 150 MCU 2. OAI Overview The OAI Gateway (MOG 500) allows the Link 150 MCU to interface with an application server as shown in the diagram below. This enables third-party applications to communicate directly with the Link 150 MCU, allowing users to retrieve and respond to information using Wireless Telephones. -
Page 9: The Oai Gateway's Front Panel
SpectraLink Corporation Open Application Interface Gateway Installation and Setup Link WTS – Link 150 MCU The OAI Gateway’s Front Panel The OAI Gateway’s front panel has the following status indicators. • indicates an internal error ERROR: • Status LEDS: •... -
Page 10: Installing The Oai Gateway
All other LEDs should be off. If the LED comes on at any time, there is a hardware problem. Note ERROR which other LEDs are on (if any) and contact SpectraLink Customer Service. Part Number: 72007507B.doc Page 10... -
Page 11: Connect The Oai Gateway To The Mcu
SpectraLink Corporation Open Application Interface Gateway Installation and Setup Link WTS – Link 150 MCU Connect the OAI Gateway to the MCU 1. The OAI Gateway must be connected as the last box in the MCU chain. Connect the OAI Gateway to the port on the MCU, using the IPC cable supplied. -
Page 12: Connect The Oai Gateway To The Application Server
SpectraLink Corporation Open Application Interface Gateway Installation and Setup Link WTS – Link 150 MCU Connect the OAI Gateway to the Application Server Using a standard 9-pin female D-type connector, connect the serial port on the front panel of the OAI Gateway to the PC, application server, or modem that will be used to interface with the application. -
Page 13: Assign Oai Function Key
SpectraLink Corporation Open Application Interface Gateway Installation and Setup Link WTS – Link 150 MCU 4. Assign OAI Function Key To access the OAI application, the user presses and an assigned number key. Follow these steps to assign a function key to initiate the OAI application. -
Page 14: Certification Test
SpectraLink Corporation Open Application Interface Gateway Installation and Setup Link WTS – Link 150 MCU 5. Certification Test When the OAI Gateway is properly connected to the application server, the LEDs should look like this: Power Error LED 1 LED 2... -
Page 15: Troubleshooting
When an alarm is detected, the Error LED will light and the OAI status LEDs will display an alarm code. Contact SpectraLink Customer Support at (800) 775-5330 (Monday through Friday, 7:00 a.m. to 6:00 p.m. Mountain Time) for additional assistance in troubleshooting your system.
Need help?
Do you have a question about the Wireless@work MOG500 and is the answer not in the manual?
Questions and answers