Table of Contents
Advertisement
Quick Links
Submersible Sump & Sewage Ejectors
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notifi cation.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
Manual Index
BARNES
BARNES
INSTALLATION MANUAL
Series: SE411HT .4Hp
1750 RPM, 60 Hz.
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
®
Form No. 107027-Rev. J
Advertisement
Table of Contents
Related Manuals for Barnes SE411HT Series
Summary of Contents for Barnes SE411HT Series
- Page 1 Manual Index BARNES BARNES ® INSTALLATION MANUAL Submersible Sump & Sewage Ejectors Series: SE411HT .4Hp 1750 RPM, 60 Hz. IMPORTANT! Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc., constant product improvement program, product changes may occur.
-
Page 2: Table Of Contents
PRESSURE GAUGE KIT (see parts list) Other brand and product names are trademarks or registered trademarks of their respective holders. ® Barnes is a registered trademark of Crane Pumps & Systems, Inc. 1999, 2000, 2002, 2003, 1/2006, 4/06, 9/06 Alteration Rights Reserved... -
Page 3: Warnings And Safety Precautions
Manual Index SAFETY FIRST! Please Read This Before Installing Or Operating Pump. This information is provided for SAFETY and to PREVENT CAUTION ! Do not block or restrict discharge hose, as EQUIPMENT PROBLEMS. To help recognize this information, discharge hose may whip under pressure. observe the following symbols: IMPORTANT! Warns about hazards that can result WARNING ! Do not wear loose clothing that may... -
Page 4: Pump Specifications
Manual Index PUMP SPECIFICATIONS SERIES: DISCHARGE ......2” NPT, Female, Vertical UPPER BEARING ......Single Row, Ball, Oil Lubricated LIQUID TEMPERATURE ..200°F (93°C) Continuous LOWER BEARING .....Single Row, Ball, Oil Lubricated VOLUTE ........Cast Iron ASTM A-48, Class 30 MOTOR: Design ....NEMA L Torque Curve, Oil Filled, MOTOR HOUSING ....Cast Iron ASTM A-48, Class 30 Squirrel Cage Induction SEAL PLATE ......Cast Iron ASTM A-48, Class 30... -
Page 5: General Information
B-4) Service Centers: C-3) Liquid Level Controls For the location of the nearest Barnes Service Center, check Figure 2 shows a typical installation for any submersible your Barnes representative or Crane Pumps & Systems, Inc., pump using a level control mounted to the discharge piping Service Department in Piqua, Ohio, telephone (937) 778-8947 with a piggy-back plug. - Page 6 Manual Index C-4) Electrical Connections: WARNING ! - Pump must be used in a circuit protected by a ground fault interrupter. WARNING ! - All model pumps and control panels must be properly grounded per THE NATIONAL ELECTRIC CODE or CANADIAN ELECTRIC CODE and STATE, PROVINCE and LOCAL electric codes.
-
Page 7: Start-Up Operation
Allow time for pump to cool sheets. These sheets are to be completed as applicable. to room temperature before handling or Return one copy to Barnes Pumps and store the second servicing. in the control panel or with the pump manual if no control panel is used. - Page 8 Manual Index F-1.2) Testing Oil: Pressure Gauge Assembly 10 PSI 1. Place pump on it’s side, remove pipe plug (24) and (See Parts List) drain oil into a clean, dry container. 2. Check oil for contamination using an oil tester with a Remove Pipe range to 30 kilovolts breakdown.
- Page 9 Manual Index Inspect all parts for signs of wear and check motor FIGURE 6 resistance values. Check capacitor (7) with an Ohm meter by grounding the capacitor by placing a screwdriver across both terminals and then removing the screwdriver. Connect Ohm meter (set on high scale) to terminals, if needle moves to infi...
-
Page 10: Replacement Parts
Manual Index Motor, Sleeve & Bearing Seal Pusher Spring Retaining Ring (3a) Rotating Member (3c) Bullet FIGURE 9 G-2 PART NUMBER: The part number consists of a six (6) digit number, which F-4.3) Replacing Exclusion Seal: appears in the catalog. A one or two letter suffi x may follow The exclusion seal (16), helps to keep debris away from the this number to designate the design confi... -
Page 11: Trouble Shooting
Manual Index TROUBLE SHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH “CAUSE”... -
Page 12: Cross-Section (Fig. 10)
Manual Index FIGURE 10... -
Page 13: Exploded View (Fig. 11)
Manual Index FIGURE 11... -
Page 14: Parts List
Manual Index PARTS KITS Pressure Gauge Kit..P/N: 085343 PARTS LIST ITEM PART No. DESCRIPTION 085584 Motor & Sleeve 093063 Seal Plate Cast Iron 068988 Shaft Seal, (Standard) Carbon/Ceramic/Buna-N 068988SB Tungsten/Tungsten/Buna-N 068988SD Silicon/Silicon/Buna-N 068988SF Carbon/Ceramic/Viton 068988SH Tungsten/Tungsten/Viton 068988SK Silicon/Silicon/Viton 068988SM Silicon/Tungsten/Buna-N 068988SN Carbon/Ni-Resist/Buna-N 017414... -
Page 15: Performance Curve
Manual Index SERIES: SE411HT Testing is performed with water specifi c gravity of 1.0 @ 68˚F (20˚C), other fl uids may vary performance... -
Page 16: Return Goods Policy
Manual Index IMPORTANT! WARRANTY REGISTRATION Your product is covered by the enclosed Warranty. Complete the Warranty Registration Form and return to Crane Pumps & Systems, Inc. Warranty Service Group If you have a claim under the provision of the warranty, contact your local Crane Pumps &... -
Page 17: Start Up Report
Manual Index START-UP REPORT FOR SUBMERSIBLE PUMPS This form is designed to provide assurance that customer service and a quality product are the number one priority with Crane Pumps & Systems, Inc (CP&S). Please fi ll out the following questions as completely and accurate as possible. When complete, mail this form to: In U.S.A Send To: In Canada Send To:... - Page 18 Manual Index CP&S control panel part no. and brand Number of pumps operated by control panel NOTE: At no time should holes be made in top of control panel, unless proper sealing devices are utilized. Control panel manufactured by others Company name Model number Short circuit protection...
-
Page 19: Warranty Registration
Manual Index IMPORTANT! WARRANTY REGISTRATION Your product is covered by the enclosed Warranty. Complete the Warranty Registration Form and return to Crane Pumps & Systems, Inc. Warranty Service Group If you have a claim under the provision of the warranty, contact your local Crane Pumps &... - Page 20 Manual Index FOLD HERE AND TAPE, DO NOT STAPLE PLACE STAMP HERE CRANE PUMPS & SYSTEMS, INC. WARRANTY SERVICE GROUP 420 THIRD STREET PIQUA, OHIO 45356 - U.S.A.