Page 1
Manual Index BARNES ® INSTALLATION MANUAL Submersible Grinder Pump ProGrind Series: PGPP 2 HP, 3450 RPM, 60 Hz. DISCONTINUED Parts may NOT be available IMPORTANT! Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc., constant product improvement program, product changes may occur.
Other brand and product names are trademarks or registered trademarks of their respective holders. ® Barnes is a registered trademark of Crane Pumps & Systems, Inc. 2002, 4/04, 5/06, 9/06, 1/07 Alteration Rights Reserved...
Page 3
Start-Up/Warranty Registration form must be either directly or through a kitchen waste on fi le at the Barnes factory in order to activate disposal: your warranty. In addition your pump must be •...
SERVICE CENTERS: Upon receiving the pump, it should be inspected for damage For the location of the nearest Barnes Service Center, check or shortages. If damage has occurred, fi le a claim imme- your Barnes representative or Crane Pumps & Systems, diately with the company that delivered the pump.
Page 6
If pump is installed with a discharge hose rather than a Wire Size - If additional cord is required consult a qualifi ed moveable fi tting assembly, make sure the discharge pipe electrician for proper wire size. has a 1/8” dia. hole approx. 5” from end nearest volute and oriented towards the pump body.
TROUBLE SHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH “CAUSE”...
PARTS KITS Seal Repair Kit ...P/N: 108302 Item #’s 6,7,13,14,15,19,20,21,25,26,27,32,35,47 Cutter Kit ....P/N: 108321 Item #’s 5,6,7,9,15,19,23 PARTS LIST ITEM PART NO. DESCRITION ITEM PART NO. DESCRITION 108344 Volute 2-31051-224 O-Ring 1-156-1 Screw, 5/16-18 x 1.00” SS 108343 Seal Plate 105818XA 14/3 Cord Set, 20Ft (STD) 108342...
Page 10
Limited 24 Month Warranty Crane Pumps & Systems warrants that products of our manufacture will be free of defects in material and workmanship under normal use and service for twenty-four (24) months after manufacture date, when installed and maintained in accordance with our instructions.This warranty gives you specifi c legal rights, and there may also be other rights which vary from state to state.
IMPORTANT! WARRANTY REGISTRATION Your product is covered by the enclosed Warranty. To complete the Warranty Registration Form go to: http://www.cranepumps.com/ProductRegistration/ If you have a claim under the provision of the warranty, contact your local Crane Pumps & Systems, Inc. Distributor. RETURNED GOODS RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”.
A Crane Co. Company START-UP REPORT General Information Pump Owner’s Name: __________________________________________________________ Address: ____________________________________________________________________ Location of Installation: _________________________________________________________ Contact Person: __________________________________Phone: _______________________ Purchased From: _____________________________________________________________ Nameplate Data Pump Model #: ___________________ Serial #: _____________________________________ Part #: __________________________ Impeller Diameter: ____________________________ Voltage: _________ Phase: _____ Ø...
Page 13
Submersible Pumps Resistance of cable and pump motor (measured at pump control): Red-Black:_______Ohms( ) Red-White:_______Ohms( ) White-Black:_______Ohms( ) Resistance of Ground Circuit between Control Panel and outside of pump: __________Ohms( ) MEG Ohms check of insulation: Red to Ground: _________ White to Ground: __________ Black to Ground: ____________ Operational Checks Is there noise or vibration present? YES___ NO___ Source of noise/vibration: ___________...