Advertisement
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notifi cation.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
MENU
HOME
BARNES
BARNES
INSTALLATION MANUAL
Submersible Grinder Pump
SUPERSEDED
Some parts may NOT
Manual Index
®
Series: SGV
3, 5, 7.5HP,
3450RPM
be available
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
Form No. 108091-Rev. J
Advertisement
Table of Contents
Related Manuals for Barnes SGV Series
Summary of Contents for Barnes SGV Series
- Page 1 MENU HOME Manual Index BARNES BARNES ® INSTALLATION MANUAL Submersible Grinder Pump Series: SGV 3, 5, 7.5HP, 3450RPM SUPERSEDED Some parts may NOT be available IMPORTANT! Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc., constant product improvement program, product changes may occur.
-
Page 2: Safety First
Other brand and product names are trademarks or registered trademarks of their respective holders. ® Barnes is a registered trademark of Crane Pumps & Systems, Inc 2000, 2002, 2003, 4/06 Alteration Rights Reserved... - Page 3 Start-Up/Warranty Registration form must be either directly or through a kitchen waste on fi le at the Barnes factory in order to activate disposal: your warranty. In addition your pump must be •...
-
Page 4: Pump Specifications
Requires overload protection to be SQUARE RINGS ....Buna-N included in control panel, Requires HARDWARE ....... 300 Series Stainless Steel Barnes Starter or Control panel, PAINT ........Air dry enamel, top coat which includes capacitors, or SEAL Design ..... Tandem Mechanical, oil fi lled capacitor pack. - Page 5 MENU HOME Manual Index MODEL VOLT PH/Hz NEMA FULL LOCKED CORD CODE CORD WINDING (Nom) START LOAD ROTOR SIZE TYPE O.D. RESISTANCE CODE AMPS AMPS ± .02 (.5) MAIN -- START in (mm) SGV3002L 1 / 60 3450 27.0 86.0 10/4 0.75 (19) 0.8 -- 3.3...
- Page 6 It is recommended that a junction box, be mounted outside the sump or be of at least Nema For the location of the nearest Barnes Service Center, check 4 (EEMAC-4) construction if located within the wet well.
- Page 7 MENU HOME Manual Index In the event of an overtemperature, the source of this NOTES: condition should be determined and rectifi ed immediately. Thermal protection shall not be used as a motor overload device. A separate motor overload device must be provided in accordance with NEC codes.
- Page 8 MENU HOME Manual Index...
- Page 9 MENU HOME Manual Index...
-
Page 10: Troubleshooting
MENU HOME Manual Index TROUBLE SHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH “CAUSE”... - Page 11 MENU HOME Manual Index...
-
Page 12: Parts Kits
MENU HOME Manual Index PARTS KITS Seal Repair Kit ...P/N: 085223 Item #’s 5,8,14,15d,16d,20,21,34,45 Overhaul Kit ....P/N: 085224 Item #’s 2,3,5,7,8,9,14,15d,16d,20,21,34,35 Cutter Kit ....P/N: 085225 Item #’s 14,25,27,30,32,33,34,35 PARTS LIST ITEM PART NO. DESCRITION ITEM PART NO. DESCRITION 051451 Gromment, Temp MOTOR: 066871... - Page 13 MENU HOME Manual Index MOVEABLE ASSEMBLY P/N: 116728* PARTS LIST For 3, 5, & 7.5HP SGV Grinders, “C” Channel Basin Package ITEM PART NO DESCRITION 115254 Check Valve/Upper Moveable 116726 Upper Pump Support Assy. 076108 Pipe Nipple 076107 Pipe Nipple 2” NPT x 6” Lg 116727 Flange Assy 107361...
- Page 14 MENU HOME Manual Index Limited 1 Year Warranty We warrant that products of our manufacture will be free of defects in material and workmanship under normal use and service for twelve (12) months after notice of owner’s acceptance, but no greater than twenty-four (24) months after receipt of shipment, when installed and maintained in accordance with our instructions.
- Page 15 MENU HOME Manual Index START-UP REPORT FOR SUBMERSIBLE PUMPS This form is designed to provide assurance that customer service and a quality product are the number one priority with Crane Pumps & Systems, Inc (CP&S). Please fi ll out the following questions as completely and accurate as possible. When complete, mail this form to: In U.S.A Send To: In Canada Send To:...
- Page 16 MENU HOME Manual Index CP&S control panel part no. and brand Number of pumps operated by control panel NOTE: At no time should holes be made in top of control panel, unless proper sealing devices are utilized. Control panel manufactured by others Company name Model number Short circuit protection...
-
Page 17: Warranty Registration
MENU HOME Manual Index IMPORTANT! WARRANTY REGISTRATION Your product is covered by the enclosed Warranty. Complete the Warranty Registration Form and return to Crane Pumps & Systems, Inc. Warranty Service Group If you have a claim under the provision of the warranty, contact your local Crane Pumps &... - Page 18 MENU HOME Manual Index FOLD HERE AND TAPE, DO NOT STAPLE PLACE STAMP HERE CRANE PUMPS & SYSTEMS, INC. WARRANTY SERVICE GROUP 420 THIRD STREET PIQUA, OHIO 45356 - U.S.A.