Toshiba B-EX6T Series Key Operation Specification page 56

9.4.1.1 Maintenance Counter/Parameter Settings Print Contents
B-EX6T1/3
<< COUNTER >>
TOTAL FEED 3.7km
FEED 2.4km
FEED1 1.3km
FEED2 0.0km
FEED3 0.0km
FEED4 0.0km
PRINT 2.4km
PRINT1 1.3km
PRINT2 0.0km
PRINT3 0.0km
PRINT4 0.0km
CUT 0
HEAD U/D 0
RIBBON 0h
SOLENOID 0h
232C ERR 0
SYSTEM ERR 0
POWER FAIL 0
<< ADJUST >>
[PC]
FEED +0.0mm
CUT +0.0mm
BACK +0.0mm
TONE(T) +0step
TONE(D) +0step
(RIBBON TORQU NORM)
RBN(FW) +0
RBN(BK) +0
(RIBBON TORQU LOW)
RBN(FW) +0
RBN(BK) +0
(RIBBON TORQU RSV1)
RBN(FW) +0
RBN(BK) +0
X ADJ. +0.0mm
THRESHOLD(R) 1.0V
THRESHOLD(T) 1.4V
<< PARAMETER SETTINGS >>
MEDIA LOAD
MOVE TO TEAROFF
HEAD UP CUT/RWD.
RIBBON SAVE
PRE PEEL OFF
BACK FEED SPEED
CALIBRATION
CODE PAGE
CTRL CODE
PEEL OFF STATUS
USB I/F STATUS
FEED KEY
KANJI CODE
EURO CODE
AUTO HEAD CHK
WEB PRINTER
RIBBON NEAR END
EX.I/O MODE
PAPER/RBN END
MAXI CODE SPEC.
XML
THRESHOLD SEL(R)
THRESHOLD SEL(T)
ENERGY TYPE(T)
ENERGY TYPE(D)
POWER SAVE TIME
RIBBON TORQUE
BASIC
BASIC TRACE
<< PANEL >>
LANGUAGE
MODEL NAME
PRINTED COUNTER
IP ADDRESS
CONTRAST
*1: If "CN" is selected for the parameter clear destination, the ENERGY TYPE parameter is not displayed on the menu and unable to be
set in the system mode and user system mode. However, the initial value (See Section 9.8.3 PARAMETER CLEAR ) will be set after a
parameter clear, so it is printed on the maintenance counter/parameter settings print label.
[QM]
[KEY]
FEED +0.0mm
CUT +0.0mm
BACK +0.0mm
TONE(T) +0step
TONE(D) +0step
RBN(FW) +0
RBN(BK) +0
RBN(FW) +0
RBN(BK) +0
RBN(FW) +0
RBN(BK) +0
[STD]
[ON] +0.0mm [MODE1]
[OFF]
[POSITION1]
[OFF]
[STD]
[OFF]
[PC-850] [0]
[AUTO]
[ON]
[OFF]
[FEED]
[TYPE1:Windows]
[B0]
[OFF]
[OFF]
[OFF]
[TTEC Standard]
[Stop immediately]
[TYPE1: Compatible]
[STD]
[MANUAL SET]
[MANUAL SET]
*1
[Generic]
*1
[NORM:Normal]
[ 15min]
[Normal]
[OFF]
[OFF]
[ENGLISH]
[ON]
[ON]
[ON]
[40]
SYSTEM PASSWORD [OFF]
<< STORAGE AREA >>
TTF AREA [
EXT CHR AREA [
BASIC AREA [
PC SAVE AREA [
OTF SAVE AREA [
<< USB >>
SERIAL NUMBER [DISABLE]
[XXXXXXXXXXXX]
<< RS-232C >>
BAUD RATE [9600]
DATA LENGTH [8]
STOP BIT [1]
PARITY [EVEN]
CONTROL [XON+READY AUTO]
<< CENTRO >>
ACK/BUSY [Rising edge]
INPUT PRIME [ON]
PLUG & PLAY [OFF]
<< LAN/WLAN >>
LAN/WLAN [AUTO]
SNMP [ON]
IP ADDRESS [192.168.010.020]
v6L[fe80::280:91ff:fe88:ea8
v6G[
SUBNET MASK [000.000.000.000]
GATEWAY ADDRESS [255.255.255.000]
SOCKET PORT [OFF] [08000]
DHCP [OFF]
DHCP CLIENT ID [FFFFFFFFFFFFFFFFFFFF]
[FFFFFFFFFFFFFFFFFFFF]
[FFFFFFFFFFFFFFFFFFFF]
[FFFFFFFFFFFFFFFFFFFF]
[FFFFFFFFFFFFFFFFFFFF]
[FFFFFFFFFFFFFFFFFFFF]
[FFFFFFFF]
DHCP HOST NAME [ABCDEFGHIJKLMNOPQRST]
[UVWXYZ123456]
CONNECTION MODE [AP MODE]
ESS ID [
[
ENCRYPTION [OFF]
WPA MODE [OFF]
AUTHENTICATION [OPEN]
802.1X SUPPLICANT [OFF]
DEFAULT KEY [ 1]
802.11bgn CHANNEL [ 1]
WINS [OFF]
WINS IP ADDRESS [000.000.000.000]
LPR [OFF]
<< RFID >>
MODULE TYPE [NONE]
TAG TYPE [NONE]
RF CHANNEL [AUTO]
RETRY POSITION [+00mm]
RETRY LABELS [ 3labels]
READ RETRY [ 5times] [4.0sec]
WRITE RETRY [ 5times] [4.0sec]
POWER LEVEL [ 0]
Q VALUE [ 0]
AGC THRESHOLD [ 0]
WRITE AGC [ 0]
RETRY MIN AGC [ 0]
TAG CHECK [PASSWORD] [ON] [ON]
MULTI WRITE [OFF]
CALIB. MODE [OFF]
CALIB. AGC [
CALIB. POSITION [+000.0mm]
ANTENNA POSITION [FRONT]
SUCCEEDED TAGS 9999999
VOID PRINT TAGS 9999999
<< RTC >>
BATTERY CHECK [ON]
RENEWAL [start of JOB]
55
0KB]
0KB]
0KB]
0KB]
0KB]
]
]
]
]
0]