Tests Menu; Network Menu - Danfoss CCR3+ Operating Manual

CCR3+ Controller
ENGLISH
LANGUAGE
11. CCR3+ DASHBOARD
(Web App Screen)
(continuous)
Note: In case of changing IP address in
CCR+ Controller, changes should also be
applied in PC local network settings.
VI.GM.A2.02
CORRECTIONS MENU:
No. Name Description
Sensor calibration: S0 ... S36 in range: ±9.9 °C
48 S0, ... , S36 Do not make calibration when sensor cables are shorter than 10 meters.
For longer cable then 10 meters, used correction factors from table below.
Cable Length
49 Useful tool for calculating cable corrections by selecting cable length (m) and cross (mm
Cable Calculator
Save settings Click »Save Settings« to confirm changes.

TESTS MENU:

No. Name Description
Open: Selected output contact is open
Close: Selected output is closed to common (C)
50 O1...O4
Auto
Factory setting: Auto
Open: selected valve is open, contact open
Close: selected valve is closed, shortcuted to common (C)
51 V1, ..., V36 Auto OnOff: selected valve works in On/off mode
AutoPWM: selected valve works in PWM mode
Factory setting: AutoPWM
Save settings Click »Save Settings« to confirm changes
Set all as Open All Open
Set all as Close All Close
Set all as AutoPWM All Auto PWM
DATA MENU
Delete all logs
No. Name Description
52 Delete all logs Erasing of log file
53 GO to By selecting time period, log files will be shown and ready for download (*.CSV)

NETWORK MENU:

No. Name Description
Enable – Modbus is switch on
54 Modbus
Disable – Modbus is switched off
Type of date transmission:
ModBus 96 (9.600)
Mod Bus 19 (19.000)
55 Modbus baud rate
ModBus 38 (38.400)
FBus
Factory setting: ModBus 96
None (transmission parity disabled)
Even (»Even« type of transmission parity enabled)
56 Modbus parity
Odd (»Odd« type of transmission parity enabled)
Factory setting: Odd
Unit Address for Mobus RTU RS485
57 Modbus address
Factory setting: 1
The IP address that the router assigned to this device when it joined the network. This number
58 LAN IP address can change if a device is disconnected and rejoins the network
Factory setting: 192.168.1.100
Identify network address of an IP address
59 LAN IP address mask
Factory setting: 255.255.255.0
The gateway address (or default gateway) is a router interface connected to the local network
60 LAN Gateway address that sends packets out of the local network
Factory setting: 192.168.1.1
Name of CCR3+ (relevant for network search)
LAN name (min. 2 Please note that after changing this value, local network dns server need to be refreshed. This
61
char., max. 15 char.) process is depend on current network configuration and can take up to few hours.
Factory setting: ccrplus
Dynamic Host Configuration Protocol
Disable
62 LAN DHCP
Enable
Factory setting: Disable
63 LAN connected clients Number of LAN connected clients to CCR3+
WIFI name (min. 2 Wi-Fi name (can be changed)
64
Factory setting: ccrwifi
char., max. 15 char.)
WIFI pass (min. 8 char., Password name (can be changed)
65
max. 15 char.) Factory setting: admin1234
66 WIFI connected client Shows IP and name of Wi-Fi connected device
Change Login Password name for access to CCR3+ App
67
password: Factory setting: admin1234
Shows Slave Unit communication status between CCR3+ Controller
Slave Unit Comm. 0% – no communication
68
Status 100% – communication OK
Possible (readable values): 0 – 100%
Save Settings Click »Save Settings« to confirm changes
2 ).
© Danfoss | 2019.02 | 11