Table of Contents
Advertisement
REPLACEMENT PARTS
The detector is not designed to be repaired in the field.
If a problem should develop, refer to the Troubleshooting
section. If it is determined that the problem is caused by
an electronic defect, the device must be returned to the
factory for repair.
DEVICE REPAIR AND RETURN
Prior to returning devices, contact the nearest local
Detector Electronics office so that a Return Material
Identification (RMI) number can be assigned.
written statement describing the malfunction must
accompany the returned device or component to
assist and expedite finding the root cause of the
failure.
Pack the unit properly. Always use sufficient packing
material. Where applicable, use an antistatic bag as
protection from electrostatic discharge.
Inadequate packaging that ultimately causes
damage to the returned device during shipment
will result in a service charge to repair the damage
incurred during shipment.
Return all equipment transportation prepaid to the factory
in Minneapolis.
It is highly recommended that a complete spare
be kept on hand for field replacement to ensure
continuous protection.
8.3
NOTE
NOTE
ORDERING INFORMATION
When ordering, please specify:
X2200 UV Flame Detector
Refer to the X2200 Model Matrix for details.
Q9033 mount is required:
Q9033A for aluminum detectors only.
Q9033B for aluminum and stainless steel detectors.
X-SERIES FLAME DETECTOR ACCESSORIES
Part Number
A
000511-029
001680-001
005003-001
006097-001
007240-001
007255-001
Q1201C1001 X-Series Laser Holder (AL/Plastic)
Q9033B Stainless Steel Swivel Mount Assembly is for
007290-001
Q9033A Aluminum Swivel Mount Assembly is for aluminum
007290-002
007307-001
o i plate for X3301 (requires inspector connector to calibrate)
o i plate for X52/X22/X98 (requires inspector connector to
007307-002
007307-003
o i plate for X3302 (requires inspector connector to calibrate)
007338-001
007338-010
Q2033A10R X3301/X3302 FOV Limiter 10° (AL)
007338-020
Q2033A20R X3301/X3302 FOV Limiter 20° (AL)
007338-030
Q2033A30R X3301/X3302 FOV Limiter 30° (AL)
007739-001
007818-001
Q1118A1001 Aluminum Air Shield/Flange Mount (AL)
007818-002
Q1118S1001 Stainless Steel Air Shield/Flange Mount (SS)
W6300B1002 Inspector Connector (Inspector Monitor
007819-001
007912-010
007912-020
007912-030
009177-001
009199-001
Q1198A1001 Dual Air Shield/Flange Mount (X9800 only)/(AL)
009207-001
009208-001
o i kit (5 plates) with Inspector Connector and Monitor X3301
o i kit (5 plates) with Inspector Connector and Monitor X52/
009208-002
101197-003
102740-002
102871-001
103922-001
103363-001
103406-001
103517-001
107427-040
19
Description
Converter RS485 to RS232
Window cleaner (6 pack)
1 oz grease for detectors (non-silicon)
Q1201 Laser
Q1116A1001, Air Shield (AL)
aluminum and stainless steel detectors
detectors only
calibrate)
Q2000A1001 X-Series Weather Shield (AL)
Magnet and Extension Pole
software included)
Spare Restrictor Plate 10° (AL)
Spare Restrictor Plate 20° (AL)
Spare Restrictor Plate 30° (AL)
Q1120A1001 Paint shield mounting ring (AL)
Inspector Monitor CD
X22/X98
Stop Plug, SS, IP66, Ex d e, M25 (SS)
Magnet
Laser Battery, 3V Lithium (laser)
Model 475 HART Communicator
14mm Hex Wrench (Steel)
Screwdriver
Stop Plug, AL, IP66, Ex d e, M25 (AL)
O-ring - Rear Cover (Viton)
95-8549
Advertisement
Table of Contents
