Table of Contents
Advertisement
Quick Links
K&A MANUFACTURING
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: 800.298.4351 FAX: 866.882.9475
www.raproducts.com
VERSION DATED: 12/3/12
ITEM # PART #
1
VARIES CONFERENCE TABLE WORKSURFACE
2
VARIES U-CHANNEL
3
51708 M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW 55
4
VARIES NewHeights DUAL COLUMN ASSEMBLY
5
52477 3/8 INTERIOR TOOTH STAR WASHER
6
52470 3/8-16 x 3/8 BUTTON HEAD SOCKET SCREW
7
VARIES NewHeights™ CROSS SUPPORT
8
800411 NewHeights™/HOVER END CAP
9
50298 NewHeights™ CONTROL BOX
10
50285 NewHeights™ HAND SWITCH
11
52498 7/32" ALLEN WRENCH
READ ALL THE INSTRUCTIONS
BEFORE BEGINNING. DO NOT
OPERATE THE UNIT UNTIL IT IS
FULLY ASSEMBLED.
2
1
STEPS 1 & 2
INSTRUCTION # 52898
HARDWARE PACK # 52883
TOOLS REQUIRED FOR ASSEMBLY:
CORDLESS DRILL
#2 PHILLIPS HEAD DRIVER BIT OR
#2 SQUARE HEAD DRIVER BIT
4mm HEX HEAD DRIVER BIT OR
ALLEN WRENCH PROVIDED
TAPE MEASURE
LEVEL
DESCRIPTION
3
4.000
DETAIL C
NewHeights™ ELECTRIC HEIGHT ADJUSTABLE CONFERENCE TABLE
ASSEMBLY INSTRUCTIONS:
STEP 1: LAY THE WORKSURFACE 1 ON A PROTECTED SURFACE WITH THE
PILOT HOLES FACING UP.
STEP 2 ALIGN THE HOLES IN THE U-CHANNELS 2 WITH THE PILOT HOLES IN
THE WORKSURFACE. ATTACH THE U-CHANNELS WITH (24) WOOD
3
SCREWS
. DO NOT OVER-TIGHTEN THE SCREWS. USE A LOW TORQUE
SETTING ON THE DRILL.
QTY.
1
STEP 3:
ALIGN THE HOLES IN THE WORKSURFACE SUPPORTS WITH THE
PILOT HOLES IN THE WORKSURFACE
2
THE INSIDE OF THE TABLE. WITH THE HELP OF AN ASSISTANT, PLACE (4)
STAR WASHERS
5
ON (4) SOCKET SCREWS
THE HOLES AT THE ENDS OF ONE OF THE CROSS SUPPORTS 7
2
THEM INTO THE HOLES IN THE T-SLOT PLATES THAT ARE PRE-INSTALLED IN
8
THE COLUMN ASSEMBLIES 4
8
STEP 4:
LEVEL THE CROSS SUPPORT AT 4" FROM THE BOTTOM OF THE
2
WORKSURFACE SUPPORT. SEE DETAIL C. FULLY TIGHTEN THE SOCKET
SCREWS
6 .
4
STEP 5: REPEAT STEPS 3 AND 4
2
AND THE OTHER COLUMNS ON THE COLUMN ASSEMBLIES
1
1
7
PRE-INSTALLED
T-SLOT PLATE
DETAIL B
1
. THE MOTOR WIRES MUST FACE
6
. INSERT THESE THROUGH
. SEE DETAIL B.
WITH THE REMAINING CROSS SUPPORT 7
8
5
A
DETAIL A
7
STEPS 3-5
. THREAD
4
.
6
4
PAGE 1 OF 4
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for RightAngle NewHeights Electric Height Adjustable Conference Table
Summary of Contents for RightAngle NewHeights Electric Height Adjustable Conference Table
- Page 1 NewHeights™ ELECTRIC HEIGHT ADJUSTABLE CONFERENCE TABLE TOOLS REQUIRED FOR ASSEMBLY: ASSEMBLY INSTRUCTIONS: CORDLESS DRILL #2 PHILLIPS HEAD DRIVER BIT OR STEP 1: LAY THE WORKSURFACE 1 ON A PROTECTED SURFACE WITH THE #2 SQUARE HEAD DRIVER BIT K&A MANUFACTURING PILOT HOLES FACING UP. 4mm HEX HEAD DRIVER BIT OR 6703 ZINSER ST., SCHOFIELD, WI 54476 ALLEN WRENCH PROVIDED...
- Page 2 STEP 6: ATTACH THE WORKSURFACE SUPPORTS ON THE COLUMN ASSEMBLIES 4 TO THE WORKSURFACE 1 USING (24) WOOD SCREWS 3 . DO NOT OVER-TIGHTEN THE SCREWS. USE A LOW TORQUE SETTING ON THE DRILL. STEP 7: ALIGN THE HOLES IN ONE OF THE CONTROL BOXES 9 WITH THE PILOT HOLES IN THE WORKSURFACE 1 . THE MULTIPLE CONNECTOR PORTS MUST FACE THE COLUMN ASSEMBLIES 4 .ATTACH IT WITH (2) WOOD SCREWS 3 .
- Page 3 STEP 10: RUN THE WIRES AS SHOWN IN THE WIRE RUNS DIAGRAM BELOW. PLUG THE WIRES INTO THE RECEPTACLES ON THE CONTROL BOXES AS SHOWN IN THE CONTROL BOX WIRING DIAGRAM BELOW LEFT. RUN THE SYNCH WIRE BETWEEN THE CONTROL BOXES AND PLUG IT INTO THE TOPS OF THE CONTROL BOXES.
- Page 4 RECEPTACLES. A POWER SURGE PROTECTOR IS RECOMMENDED. THE NewHeights™ WORKSTATION IS NOW READY FOR USE. TROUBLESHOOTING IF YOU ARE HAVING ANY PROBLEMS WITH THE TABLE OPERATION, CONTACT RIGHTANGLE™ SERVICE AT 800-298-4351 OR orders@raproducts.com. WARRANTY INFORMATION: NewHeights™ PRODUCTS ARE WARRANTED TO BE FREE OF DEFECTS DUE TO MANUFACTURING OR MATERIALS AS FOLLOWS: 2 YEARS ON THE GEAR AND/OR MOTOR, INCLUDING THE CONTROL BOX AND HAND SWITCH.
Need help?
Do you have a question about the NewHeights Electric Height Adjustable Conference Table and is the answer not in the manual?
Questions and answers