Subscribe to Our Youtube Channel
Related Manuals for RightAngle NewHeights Victory Conference
Summary of Contents for RightAngle NewHeights Victory Conference
- Page 1 NewHeights™ Victory Conference Assembly Instructions Warranty: raproducts.com/resources/warranty Instruction #54860 • Dated: 06/23/2023 1 of 14...
- Page 2 Product and its height adjustment mechanism to avoid risk of physical injury or electric shock. KEEP CHILDREN AWAY FROM THE PRODUCT, ITS CONTROL UNITS, AND KEYPADS. RightAngle • 800.298.4351 • www.raproducts.com 2 of 14...
- Page 3 5/8” Washer Head Wood Screw x37 G. 5/8” Wood Screw x4 H. 4mm Ball End Screwdriver x1 M4 Allen Wrench x1 Parts Leg Column x2 K. Reinforcement Panel x1 U-Channel x2 M. Divider Cover x1 RightAngle • 800.298.4351 • www.raproducts.com 3 of 14 ®...
- Page 4 Cord Clip x1 U. Grommet Inserts x2 V. J-Channel Raceway x2 W. Mesh Cable Sleeve x1 X. Mounting Head Cable Tie x1 May be 4-button switch if up- graded for order 20” long RightAngle • 800.298.4351 • www.raproducts.com 4 of 14 ®...
- Page 5 • Using the ball end screw driver (H), secure the center panels (N) the the side panel (O). 4mm Ball End Screwdriver (H) RightAngle • 800.298.4351 • www.raproducts.com 5 of 14 ®...
- Page 6 Step 3 • Repeat step 2 with the second side panel (O). RightAngle • 800.298.4351 • www.raproducts.com 6 of 14 ®...
- Page 7 It may be helpful to have a second person to assist during this step. • Repeat with the second leg column on the other side of the table. NOTE: The second center panel is removed in the image to show internal assembly. RightAngle • 800.298.4351 • www.raproducts.com 7 of 14 ®...
- Page 8 • Carefully place the worksurface (P) on a flat, protective surface with the pre-drilled pilot holes facing upwards. • Align the two u-channels (L) onto the worksurface (P) and align with the pre-drilled pilot holes. • Secure to the worksurface using 10 washer head work screws (F) per u-channel. RightAngle • 800.298.4351 • www.raproducts.com 8 of 14...
- Page 9 • Align the control switch (S) with the pre-drilled pilot holes towards the edge of the worksurface. Pilot holes available on either side of the worksurface. May be the two or four button switch depending on order. • Secure to the worksurface using two wood screws (G). RightAngle • 800.298.4351 • www.raproducts.com 9 of 14...
- Page 10 • Feed the control switch cable through the cord clip (T). Select the clip position and secure to the worksurface using a washer head wood screw (F). There is no pre-drilled pilot hole for this step. Control Switch Cable RightAngle • 800.298.4351 • www.raproducts.com 10 of 14...
- Page 11 • Carefully raise the table up to give enough clearance for you to secure the base to the worksurface. The table does not need to go to its highest position. Be sure the worksurface is steady. Control Box End View Power Cable Switch Cable Motor Cable RightAngle • 800.298.4351 • www.raproducts.com 11 of 14 ®...
- Page 12 Once in place, the raceways are difficult to remove and reposition. • If able, direct the cords towards the end of the table where the power cord plugs into the control box. RightAngle • 800.298.4351 • www.raproducts.com 12 of 14 ®...
- Page 13 (N) and the leg columns (J). It works best to insert diagonally, inserting one end before the other. • Place the grommet inserts (U) into the two grommet holes on the divider cover (M). RightAngle • 800.298.4351 • www.raproducts.com 13 of 14 ®...
- Page 14 To complete reset mode, press and hold the down arrow until the table reaches it’s lowest height and then slightly rises. • With the reset complete, your install is complete. RightAngle • 800.298.4351 • www.raproducts.com 14 of 14 ®...
Need help?
Do you have a question about the NewHeights Victory Conference and is the answer not in the manual?
Questions and answers