Precautions; Rack Mounting - Digigram AUDIOWAY BRIDGE B1 User Manual

AUDIOWAY BRIDGE B1, B2, B3
2.2

PRECAUTIONS

WARNING
DOUBLE POLE / NEUTRAL
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from Always follow the basic precautions listed belo
electrical shock, short-circuiting, damages, fire or other hazards. circuiting, damages, fire or other hazards.
These precautions include, but are not limited to, the following: These precautions include, but are not limited to, the following:

Do not apply excessive pressure on connectors or any other part of the board. Do not touch the Do not apply excessive pressure on connectors or any othe
metallic sharp parts (pins) of the product. metallic sharp parts (pins) of the product.

This product is electrostatic sensitive; make sure you check this before touching or using it. This product is electrostatic sensitive; make sure you check this before touching or using it. This product is electrostatic sensitive; make sure you check this before touching or using it.

The disconnect devices of the AUDIOWAY BRIDGE
supply (option) and the appliance inlet on the rear side of the unit. These must be easily reachable. supply (option) and the appliance inlet on the rear side of the unit. These must be easily reachable. supply (option) and the appliance inlet on the rear side of the unit. These must be easily reachable.

To prevent electric shock, unplug the unit before handling. The achievement of other operations not To prevent electric shock, unplug the unit before handling. The achievement of other operations not To prevent electric shock, unplug the unit before handling. The achievement of other operations not
mentioned in this document is prohibited. Repairs can be performed only by a technician trained and ned in this document is prohibited. Repairs can be performed only by a technician trained and ned in this document is prohibited. Repairs can be performed only by a technician trained and
qualified.

Each connection must be Safety Extra Low Voltage kind (SELV), and must stay inside buildings. Each connection must be Safety Extra Low Voltage kind (SELV), and must stay inside buildings. Each connection must be Safety Extra Low Voltage kind (SELV), and must stay inside buildings.

Always use a power cable with a plug according to the current standards in the country of use Always use a power cable with a plug according to the cur
FINLAND: "Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan" FINLAND: "Laite on liitettävä suojamaadoitus
NORWAY: "Apparatet må tilkoples jordet stikkontakt" : "Apparatet må tilkoples jordet stikkontakt"
SWEDEN: "Apparaten skall anslutas till jordat uttag" : "Apparaten skall anslutas till jordat uttag"

2.3 RACK MOUNTING

This product is designed to be rack-mounted. Be sure to observe following installation rules of this kind of
equipment:

Do not block the vents. This device has ventilation holes on the both side to prevent the internal
temperature from becoming too high. Inadequate ve temperature from becoming too high. Inadequate ventilation can result in overheating, possibly causing
damage to the device(s), or even fire. damage to the device(s), or even fire.

Elevated Operating Ambient - If installed in a closed or multi
temperature of the rack environment may be greater than r temperature of the rack environment may be greater than room ambient. Therefore, consideration should
be given to installing the equipment in an environment compatible with the maximum ambient be given to installing the equipment in an environment compatible with the maximum ambient be given to installing the equipment in an environment compatible with the maximum ambient
temperature specified by the manufacturer. temperature specified by the manufacturer.

Reduced Air Flow - Installation of the equipment in a rack should be such tha
required for safe operation of the equipment is not compromised. required for safe operation of the equipment is not compromised.
In some cases, to be sure to ensure sufficient airflow, leave the rear and the front of the rack open, leave In some cases, to be sure to ensure sufficient airflow, leave the rear and the front of the rack open, leave In some cases, to be sure to ensure sufficient airflow, leave the rear and the front of the rack open, leave
sufficient space (>5cm) on each side of the rack, and le sufficient space (>5cm) on each side of the rack, and leave space above rack (>1cm).
Or it can be better to have appropriate fan kit in the multi Or it can be better to have appropriate fan kit in the multi-unit rack

Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition
is not achieved due to uneven mechanical loading. is not achieved due to uneven mechanical loading.
B3
FUSING
w to avoid the possibility of serious injury or even death from
AUDIOWAY BRIDGEunit are the appliance inlet of the auxiliary power
koskettimilla varustettuun pistorasiaan"
mounted. Be sure to observe following installation rules of this kind of mounted. Be sure to observe following installation rules of this kind of
This device has ventilation holes on the both side to prevent the internal This device has ventilation holes on the both side to prevent the internal
If installed in a closed or multi-unit rack assembly, the operating ambient
Installation of the equipment in a rack should be such that the amount of air flow
Mounting of the equipment in the rack should be such that a hazardous condition Mounting of the equipment in the rack should be such that a hazardous condition
r part of the board. Do not touch the
are the appliance inlet of the auxiliary power
rent standards in the country of use
ntilation can result in overheating, possibly causing
unit rack assembly, the operating ambient
oom ambient. Therefore, consideration should
ave space above rack (>1cm).
User's Manual AUDIOWAY BRIDGE v1.0 User's Manual AUDIOWAY BRIDGE v
U '
SER S MANUAL V
t the amount of air flow
Page 6/55
1.0