1. Manuals
  2. Brands
  3. Landoll Manuals
  4. Farm Equipment
  5. Tilloll 877
  6. Operator's manual

Landoll Tilloll 877 Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Model 877
Tilloll
Operator Manual
LANDOLL CORPORATION
1900 North Street
Marysville, Kansas 66508
(785) 562-5381
800-428-5655 ~ WWW.LANDOLL.COM
F-1072-0320
03/2020-Present

Advertisement

Table of Contents
loading

Related Manuals for Landoll Tilloll 877

Summary of Contents for Landoll Tilloll 877

  • Page 1 Model 877 Tilloll Operator Manual LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-1072-0320 03/2020-Present...
  • Page 2 Manuals for the 877 Tilloll MANUAL NUMBER MANUAL NAME F-1072 877 Operator’s Manual F-1073 877 Parts Manual...

  • Page 3: Table Of Contents

    Table of Contents Introduction and Safety Information Understanding Safety Statements ..........1-2 Decal Safety .
  • Page 4 Spray Shield Adjustment ........... . 4-9 Spray Boom Location .

  • Page 5: Introduction And Safety Information

    Introduction and Safety Information Introduction The Landoll Model 877 Tilloll is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation.

  • Page 6: Understanding Safety Statements

    INTRODUCTION AND SAFETY INFORMATION Understanding Safety Decal Safety Statements 1. Examine safety decals and be sure you have the correct safety decals for the implement. You will find various types of safety information on the 2. Keep these signs clean so they can be observed following pages and on the machine signs (decals) readily.

  • Page 7: Attaching, Detaching, And Storage

    INTRODUCTION AND SAFETY INFORMATION 4. Do not transport at speeds over 20 MPH under good conditions. Never travel at a speed which does not allow adequate control of steering and stopping. Reduce speed if towed load is not equipped with brakes 5.

  • Page 8: Safety Chain

    INTRODUCTION AND SAFETY INFORMATION Safety Chain 3. Attach the chain to the tractor drawbar support or specified anchor location. Allow only enough slack in 1. Use a chain with a strength rating equal to or greater the chain to permit turning. The distance from hitch than the gross weight of towed machinery, which is pin to attachment point or intermediate support point 10,100 pounds minimum in accordance with ASAE...

  • Page 9: Standard Specifications

    Chapter 2 Standard Specifications Model Specifications 877 Tilloll Model Number 877-30 877-35 877-40 Working Width 30'-0” 34'-6” 40'-0” Transport Width 16'-6” 20'-4” 17'-9” Transport Height 8'-6” 13'-0” 13'-9” Number of Shanks Number of 20” Blades Estimated Weight (lbs.) 15,800 16,700 18,800 Tire Size 320/70 R15...

  • Page 10: General Torque Specifications (Rev. 4/97)

    STANDARD SPECIFICATIONS General Torque Specifications (rev. 4/97) TORQUE SPECIFIED IN FOOT POUNDS - This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition).

  • Page 11: Hydraulic Fitting Torque Specifications

    STANDARD SPECIFICATIONS Hydraulic Fitting Torque Specifications TORQUE IS SPECIFIED IN FOOT POUNDS- 37 JIC, ORS, & ORB (REV. 10/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition).
  • Page 12 STANDARD SPECIFICATIONS 11 BLADE DISC 12 BLADE DISC 37-1/2 2-3/8 ASSEMBLY ASSEMBLY 22-1/2 76” SPRAY 83” SPRAY 16-1/2 SHIELD SHIELD ASSEMBLY ASSEMBLY Figure 2-1: Disc Gang & Spray Shield Placement 30’ LH F-1072-0320...
  • Page 13 STANDARD SPECIFICATIONS 12 BLADE DISC 11 BLADE DISC ASSEMBLY ASSEMBLY 37-1/2 2-3/8 22-1/2 83” SPRAY 76” SPRAY 16-1/2 SHIELD SHIELD ASSEMBLY ASSEMBLY Figure 2-2: Disc Gang & Spray Shield Placement 30’ RH...
  • Page 14 STANDARD SPECIFICATIONS 8 BLADE DISC 7 BLADE DISC 12 BLADE DISC ASSEMBLY ASSEMBLY ASSEMBLY 6-1/4 2-1/8 37-1/2 22-1/2 37-1/2 37-1/2 11-3/4 55” SPRAY 48” SPRAY 83” SPRAY 16-1/2 SHIELD SHIELD SHIELD ASSEMBLY ASSEMBLY ASSEMBLY Figure 2-3: Disc Gang & Spray Shield Placement 35’ LH F-1072-0320...
  • Page 15 STANDARD SPECIFICATIONS 12 BLADE DISC 7 BLADE DISC 8 BLADE DISC ASSEMBLY ASSEMBLY ASSEMBLY 6-1/4 37-1/2 2-1/8 37-1/2 37-1/2 22-1/2 11-3/4 83” SPRAY 48” SPRAY 55” SPRAY 16-1/2 SHIELD SHIELD SHIELD ASSEMBLY ASSEMBLY ASSEMBLY Figure 2-4: Disc Gang & Spray Shield Placement 35’ RH...
  • Page 16 STANDARD SPECIFICATIONS 12 BLADE DISC ASSEMBLY 8 BLADE DISC 11 BLADE DISC ASSEMBLY ASSEMBLY 22-1/2 37-1/2 9-1/2 2-5/8 37-1/2 37-1/2 55” SPRAY 76” SPRAY 16-1/2 SHIELD SHIELD ASSEMBLY ASSEMBLY 83” SPRAY SHIELD ASSEMBLY Figure 2-5: Disc Gang & Spray Shield Placement 40’ LH F-1072-0320...
  • Page 17 STANDARD SPECIFICATIONS 12 BLADE DISC 7 BLADE DISC 8 BLADE DISC ASSEMBLY ASSEMBLY ASSEMBLY 22-1/2 37-1/2 2-5/8 37-1/2 9-1/2 37-1/2 76” SPRAY 55” SPRAY 16-1/2 SHIELD SHIELD ASSEMBLY ASSEMBLY 83” SPRAY SHIELD ASSEMBLY Figure 2-6: Disc Gang & Spray Shield Placement 40’ RH...
  • Page 18 STANDARD SPECIFICATIONS NOTE: LOCATION OF CENTER SHANK MOUNT 4-5/8 11-5/8 2-3/4 3-7/8 8-1/8 2-3/8 10-7/8 10-1/8 3-1/8 5-1/4 2-1/4 2-5/8 2-1/8 19-1/8 1-3/4 11-3/8 10-7/8 20-5/8 12-7/8 NOTE: LOCATION OF EXTENSION SPRING MOUNT Figure 2-7: Shank Placement 30’ LH 2-10 F-1072-0320...
  • Page 19 STANDARD SPECIFICATIONS 4-5/8 11-1/2 3-7/8 2-5/8 1-7/8 2-1/2 10-7/8 5-1/8 3-1/8 10-1/8 2-1/2 2-1/4 2-1/4 12-7/8 20-1/2 19-1/8 11-1/2 1-7/8 NOTE: LOCATION 10-7/8 OF EXTENSION SPRING MOUNT Figure 2-8: Shank Placement 30’ RH 2-11...
  • Page 20 STANDARD SPECIFICATIONS NOTE: LOCATION OF CENTER SHANK MOUNT 3-5/8 4-5/8 12-1/8 2-3/8 23-1/8 16-1/8 3-7/8 10-7/8 5-1/8 3-1/8 2-1/4 10-1/8 20-3/8 2-1/4 2-1/4 2-5/8 19-1/8 11-3/8 14-1/8 12-7/8 3-1/8 20-5/8 NOTE: LOCATION 9-5/8 OF EXTENSION SPRING MOUNT Figure 2-9: Shank Placement 35’ LH 2-12 F-1072-0320...
  • Page 21 STANDARD SPECIFICATIONS 4-5/8 3-5/8 2-3/8 1-7/8 12-1/8 23-1/8 3-7/8 10-7/8 20-3/8 5-1/8 3-1/8 10-1/8 2-5/8 2-1/4 2-1/4 12-7/8 14-1/8 19-1/8 11-3/8 20-5/8 3-1/8 NOTE: LOCATION OF EXTENSION 9-5/8 SPRING MOUNT Figure 2-10: Shank Placement 35’ RH 2-13...
  • Page 22 STANDARD SPECIFICATIONS NOTE: LOCATION OF CENTER SHANK MOUNT 3-1/2 4-5/8 3-7/8 16-1/8 11-1/4 10-7/8 23-1/8 3-1/8 10-1/8 5-1/8 2-1/4 19-1/2 2-3/4 12-7/8 20-3/4 10-1/2 19-1/8 14-1/8 NOTE: LOCATION 10-7/8 OF EXTENSION SPRING MOUNT Figure 2-11: Shank Placement 40’ LH 2-14 F-1072-0320...
  • Page 23 STANDARD SPECIFICATIONS 4-5/8 3-1/2 2-1/8 3-7/8 1-7/8 11-3/8 23-1/8 10-7/8 5-1/8 3-1/8 10-1/8 19-1/2 2-3/4 2-1/4 12-7/8 10-1/2 14-1/8 19-1/8 20-3/4 NOTE: LOCATION 10-7/8 OF EXTENSION SPRING MOUNT Figure 2-12: Shank Placement 40’ RH 2-15...
  • Page 24 STANDARD SPECIFICATIONS 7-1/4 86-1/2” REEL 91” REEL 1-1/4 2-3/4 14-1/2 42-1/2 9-1/4 14-3/4 85” HARROW 92-1/2” HARROW NOTE: HARROW ARM NOTE: HARROW ARM NOTE: HARROW ARM MOUNTS IN MIDDLE HOLES MOUNTS IN LEFT HOLES MOUNTS IN RIGHT HOLES OF FRONT HARROW BAR OF MIDDLE HARROW BAR OF REAR HARROW BAR Figure 2-13: Reel &...
  • Page 25 STANDARD SPECIFICATIONS 7-1/4 91” REEL 86-1/2” REEL 1-1/4 2-3/4 42-1/2 14-1/2 14-3/4 9-1/4 92-1/2” HARROW 85” HARROW NOTE: HARROW ARM NOTE: HARROW ARM NOTE: HARROW ARM MOUNTS IN RIGHT HOLES MOUNTS IN LEFT HOLES MOUNTS IN MIDDLE HOLES OF REAR HARROW BAR OF MIDDLE HARROW BAR OF FRONT HARROW BAR Figure 2-14: Reel &...
  • Page 26 STANDARD SPECIFICATIONS 5-3/4 114” REEL 91” REEL 2-3/4 1-1/2 9-1/4 72-1/2 14-3/4 115” HARROW 92-1/2” HARROW NOTE: HARROW ARM NOTE: HARROW ARM NOTE: HARROW ARM MOUNTS IN MIDDLE HOLES MOUNTS IN LEFT HOLES MOUNTS IN RIGHT HOLES OF FRONT HARROW BAR OF MIDDLE HARROW BAR OF REAR HARROW BAR Figure 2-15: Reel &...
  • Page 27 STANDARD SPECIFICATIONS 5-3/4 91” REEL 114” REEL 1-1/2 2-3/4 72-1/2 9-1/4 14-3/4 92-1/2” HARROW 115” HARROW NOTE: HARROW ARM NOTE: HARROW ARM NOTE: HARROW ARM MOUNTS IN RIGHT HOLES MOUNTS IN LEFT HOLES MOUNTS IN MIDDLE HOLES OF REAR HARROW BAR OF MIDDLE HARROW BAR OF FRONT HARROW BAR Figure 2-16: Reel &...
  • Page 28 STANDARD SPECIFICATIONS 5-1/2 5-1/2 55” REEL 82” REEL 82” REEL 91” REEL 9-3/4 27-1/2 1-1/2 9-1/4 14-3/4 12-3/4 27-1/2 70” HARROW 92-1/2” HARROW NOTE: HARROW ARM NOTE: HARROW ARM NOTE: HARROW ARM MOUNTS IN MIDDLE HOLES MOUNTS IN LEFT HOLES MOUNTS IN RIGHT HOLES OF FRONT HARROW BAR OF MIDDLE HARROW BAR...
  • Page 29 STANDARD SPECIFICATIONS 5-1/2 91” REEL 82” REEL 55” REEL 1-1/2 27-1/2 9-3/4 9-1/4 14-3/4 12-3/4 27-1/2 92-1/2” HARROW 70” HARROW NOTE: HARROW ARM NOTE: HARROW ARM NOTE: HARROW ARM MOUNTS IN RIGHT HOLES MOUNTS IN LEFT HOLES MOUNTS IN MIDDLE HOLES OF REAR HARROW BAR OF MIDDLE HARROW BAR OF FRONT HARROW BAR...
  • Page 30 STANDARD SPECIFICATIONS NOTE: RIGHT WING SHOWN, WING SUPPORT PLACEMENT IS SAME ON LEFT WING SHORT WING SUPPORT 8-7/8 LONG WING SUPPORT 11-7/8 Figure 2-19: Wing Supports Placement 30’ 2-22 F-1072-0320...
  • Page 31 STANDARD SPECIFICATIONS NOTE: WING SUPPORTS USED ON RIGHT CENTER FRAME AND WING ONLY 2-1/2 WING SUPPORT WING SUPPORT 2-1/2 Figure 2-20: Wing Supports Placement 35’ RH 2-23...
  • Page 32 STANDARD SPECIFICATIONS NOTE: WING SUPPORTS USED ON RIGHT CENTER FRAME AND WING ONLY 5-1/2 WING SUPPORT WING SUPPORT 6-3/8 Figure 2-21: Wing Supports Placement 40’ RH 2-24 F-1072-0320...
  • Page 33 STANDARD SPECIFICATIONS NOTE: ROUTE WIRING HARNESS’S UNDER ALL HOSE LOOPS AND CLAMPS TO FRONT OF HITCH NOTE: SECURE WIRING HARNESS’S TO CENTER FRAME AS NEEDED WITH PLASTIC TIE STRAPS PROVIDED 2 PIN 2 PIN CONNECTOR CONNECTOR 3 PIN 3 PIN AG LED AG LED CONNECTOR...
  • Page 34 STANDARD SPECIFICATIONS Table provided for general use. NOTES: 2-26 F-1072-0320...

  • Page 35: Assembly Instructions

    Chapter 3 Assembly Instructions It is very important that your new 877 Tilloll be properly  WARNING assembled, adjusted and lubricated before use. Illustrations in this section show proper assembly Do not attempt to lift heavy parts (such as the procedures.

  • Page 36: Frame And Hitch Assembly

    ASSEMBLY INSTRUCTIONS Frame and Hitch Assembly 6. Insert a 3/4-10 x 7 hex head cap screw into the hose holder tube on the left side of the hitch from the bottom side so the threads point upward. Hold in IMPORTANT place with a 3/4 prevailing torque flange nut with the Read all safety precautions at the front of the section flange pointing upward as well.
  • Page 37 ASSEMBLY INSTRUCTIONS 1/4-20 X 1 HEX BOLT 1-1/4 X 5-5/8 PIN WING NUT 3/4-10 FLANGE 1/4 X 2 COTTER PIN LOCK NUT HOSE HOLDER BRACKET DETAIL A 3/4-16 X 3-1/2 5/8-11 X 6 HEX BOLT HEX BOLT STORE-AWAY HARNESS MAST LEVELER LOCK NUT FRONT HOLE...

  • Page 38: Wing Frame Assembly

    ASSEMBLY INSTRUCTIONS Wing Frame Assembly 3. On 40’ models, assemble the wing frames to the center frame using 1-1/4-7 x 8 hex bolts, 1-1/4 1. On 30’ models, assemble the wing frames to the narrow flat washers and 1-1/4 locknuts center frame using.
  • Page 39 ASSEMBLY INSTRUCTIONS 1 LOCK NUT 1 NARROW FLAT WASHER 1-1/4 FLAT WASHER 1 NARROW WING FOLD FLAT WASHER PLATE DETAIL A 1 FLAT WASHER 1-8 X 7-1/2 HEX BOLT 1-8 X 7-1/2 HEX BOLT WING FRAME 5/8 LUG NUTS DETAIL A TIRE/WHEEL ASSEMBLY Figure 3-2: Wing Frame Assembly 30’...
  • Page 40 ASSEMBLY INSTRUCTIONS 1-1/4 LOCK NUT 1-1/4 NARROW FLAT WASHER 1-1/4 DETAIL A FLAT WASHER WING FOLD PLATE 1-1/4 NARROW FLAT WASHER 1-1/4-7 X 8 1-1/4 HEX BOLT FLAT WASHER LOCK NUT WING EXTENSION 1-1/4-7 X 8 HEX BOLT DETAIL B 5/8-11 X 2 HEX BOLT DETAIL B...
  • Page 41 ASSEMBLY INSTRUCTIONS 1-1/4 LOCK NUT 1-1/4 NARROW FLAT WASHER 1-1/4 DETAIL A FLAT WASHER WING FOLD PLATE 1-1/4 NARROW FLAT WASHER 1-1/4-7 X 8 1-1/4 HEX BOLT FLAT WASHER DETAIL B LOCK NUT 1-1/4-7 X 8 HEX BOLT 5/8-11 X 1-1/2 HEX BOLT WING FRAME DETAIL B...

  • Page 42: Wing Fold Support Assembly

    ASSEMBLY INSTRUCTIONS Wing Fold Support Assembly See Figures 3-7 for 40’ models, assemble the wing supports to the RH center frame using 5/8 x 4-11/16 See Figures 3-5 for 30’ models, assemble the wing x 7-3/4 u-bolts and 5/8 locknuts and to the RH wing supports to the RH and LH wing frames using 5/8 x frame using 5/8 x 2 bolts and 5/8 lock nuts (See...
  • Page 43 ASSEMBLY INSTRUCTIONS WING 5/8 LOCK SUPPORT NUTS 5/8 X 4-11/16 X 5-1/2 U-BOLTS RH WING FRAME SHOWN 5/8 LOCK NUTS WING SUPPORT 5/8 X 4-11/16 X 5-1/2 U-BOLTS Figure 3-5: Wing Support Assembly 30’...
  • Page 44 ASSEMBLY INSTRUCTIONS 5/8-11 X 2 HEX BOLTS 5/8 LOCK NUTS WING WING SUPPORT RH WING SUPPORT FRAME 5/8 X 4-11/16 X 5-1/2 U-BOLTS 5/8 LOCK RH CENTER NUTS FRAME WING SUPPORT 5/8 LOCK NUTS WING SUPPORT 5/8 X 4-11/16 X 4-1/2 U-BOLTS Figure 3-6: Wing Support Assembly 35’...
  • Page 45 ASSEMBLY INSTRUCTIONS 5/8-11 X 2 HEX BOLTS WING SUPPORT RH WING FRAME RH CENTER FRAME 5/8 LOCK NUTS 5/8 LOCK WING NUTS SUPPORT 5/8 X 4-11/16 X 7-3/4 U-BOLTS WING SUPPORT WING SUPPORT Figure 3-7: Wing Support Assembly 40’ 3-11...

  • Page 46: Shank, Clamp, And Sweep Assembly

    ASSEMBLY INSTRUCTIONS Shank, Clamp, and Sweep 4. Install shanks in spring shank assembly. Slide shank into spring clamp assembly and fasten tight using Assembly 5/8-11 x 1-3/4 round head square neck screw and 5/8-11 flange head lock nut See Figures 3-8.
  • Page 47 ASSEMBLY INSTRUCTIONS SPRING CLAMP ASSEMBLY 1/2 LOCK NUT 5/8-11 X 1-3/4 ROUND HEAD SQUARE NECK SCREW SHANK 1/2-13 X 3-5/8 HEX BOLT 5/8 -11 FLANGE LOCK NUT SHANK & SWEEP CLAMP SHANK ASSEMBLY 7/16-14X1-1/2 PLOW BOLT 5/8-11 X 6-1/2 HEX BOLT FLOW DIVIDER VALVE BRACKET MOUNTING...

  • Page 48: Disc Gang And Spray Shield Installation

    ASSEMBLY INSTRUCTIONS Disc Gang and Spray Shield NOTE Installation Outside disc blade on all main frame disc gangs are not equipped with a scraper. See Figures 2-1 through for location on frame. 6. Attach spray shield adjustment bracket to frame, as 2.
  • Page 49 ASSEMBLY INSTRUCTIONS 5/8 X 3-11/16 5/8 LOCK X 5-3/8 U-BOLT 4 HOLE PLATE 5/8 LOCK 5 HOLE PLATE 5/8-11 X 5-1/2 HEX BOLT 5/8 X 2-5/8 X 6-1/8 U-BOLT BRACKET PLATE 5/8-11 X 2 5/8-11 X 2-1/2 HEX BOLT SPRAY SHIELD HEX BOLT ADJUSTMENT SUPPORT...

  • Page 50: Hydraulic Lift Installation

    ASSEMBLY INSTRUCTIONS Hydraulic Lift Installation IMPORTANT Mount double pilot check valves so that the ports V1 NOTE and V2 are facing the flow divider valve with V1 port See Figures 3-10 for Hydraulic Lift Installation. behind the V2 port. Install hose A in V1 ports of each See Figures 3-11 3-12 for proper Hydraulic Lift...
  • Page 51 ASSEMBLY INSTRUCTIONS 90° ADAPTER 5/16-18 X 3 HEX SCREW 3/8-16 X 1-3/4 #12 TO #8 HEX SCREW ADAPTER 3/8 LOCK 5/16 HEX WASHER 5/16 FLAT 3/8 X 146” HOSE 877-30’ #8 TO #8 WASHER 3/8 X 212” HOSE 877-35’ ADAPTER 3/8 X 244”...
  • Page 52 ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS Figure 3-11: Lift Hydraulic Placement LH 877-30’ 3-18 F-1072-0320...
  • Page 53 ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS Figure 3-12: Lift Hydraulic Placement RH 877-30’ 3-19...
  • Page 54 ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS Figure 3-13: Lift Hydraulic Placement LH 877-35’ 3-20 F-1072-0320...
  • Page 55 ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS Figure 3-14: Lift Hydraulic Placement RH 877-35’ 3-21...
  • Page 56 ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS Figure 3-15: Lift Hydraulic Placement LH 877-40’ 3-22 F-1072-0320...
  • Page 57 ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS Figure 3-16: Lift Hydraulic Placement RH 877-40’ 3-23...

  • Page 58: Hydraulic Fold Installation All Models

    ASSEMBLY INSTRUCTIONS Hydraulic Fold Installation 4. On 35’ and 40’ models, only after the fold cylinders have been charged with oil, assemble the rod end of All Models the fold cylinder to the wing fold plates and wing fold roller using 1-1/4 x 8 bolts, 1-1/4 flat washers and 1.
  • Page 59 ASSEMBLY INSTRUCTIONS 3-1/2 X 16 CYLINDER 3/8 X 67” HOSE 3/8 X 72” HOSE 3-1/2 X 16 CYLINDER 3/8 X 50” HOSE 3/8 X 86” HOSE ADAPTER 3/4-16 CROSS 90° ELBOW 3/8 X 86” HOSE 1/16 RESTRICTOR 3/8 X 72” HOSE 3/8 X 72”...
  • Page 60 ASSEMBLY INSTRUCTIONS 4-1/2 X 16 CYLINDER 3/8 X 146” HOSE 877-35’ 3/8 X 140” HOSE 877-40’ 4-1/2 X 16 CYLINDER 3/8 X 67” HOSE 3/8 X 126-1/4” HOSE 877-35’ 3/8 X 156” HOSE 877-40’ 90° ELBOW ADAPTER 3/8 X 50” HOSE 1/16 RESTRICTOR 4-1/2 X 20 3/8 X 67”...
  • Page 61 ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS Figure 3-20: Hydraulic Fold Placement 877-30’ 3-27...
  • Page 62 ASSEMBLY INSTRUCTIONS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS AND LOOPS Figure 3-21: Hydraulic Fold Placement 877-35’-40’ 3-28 F-1072-0320...
  • Page 63 ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-29...

  • Page 64: Reel Assembly Installation

    ASSEMBLY INSTRUCTIONS Reel Assembly Installation  CAUTION IMPORTANT When working with the reels use care because they rotate freely and can catch an arm, hand, or 1. Read all safety precautions at the front of the foot and can cause severe injury. section before attempting any of the following procedures.
  • Page 65 ASSEMBLY INSTRUCTIONS CENTER REEL 5/8-11 X 8 BRACKET PLATE HEX BOLT 5/8-11 X 3-1/2 HEX BOLT DETAIL A REEL BRACKET SPACER 5/8-11 X 2-1/2 CENTER REEL HEX BOLT BRACKET 5/8-11 X 8 WELDMENT HEX BOLT 5/8-11 CENTER REEL LOCK NUT BRACKET PLATE 1 X 11/16 ROUND TUBE...

  • Page 66: Harrow Assembly Installation

    ASSEMBLY INSTRUCTIONS Harrow Assembly Installation Install harrow springs and chains as shown in Figure 3-23 using 1/2-13 x 4 hex head cap screws and hex lock nuts. The top spring is anchored in the IMPORTANT 1st hole from the top. Front lower spring and rear Read all safety precautions at the front of the section lower spring are anchored in the 7th hole from the before attempting any of the following procedures.
  • Page 67 ASSEMBLY INSTRUCTIONS DETAIL A 5/8 U-BOLT DETAIL A 1/2-13 X 2-1/2 HEX BOLT HANGER ARM 5/8-11 LOCK NUT 1/2-13 X 4 HEX BOLT 5/32 X 1-1/4 COTTER PIN 1/2 X 2 CLEVIS PIN 1/2-13 X2-1/2 HEX BOLT SPRING 1/2-13 LOCK NUT CHAIN ADJUSTMENT ARM 1/2-13 LOCK NUT...
  • Page 68 ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-34 F-1072-0320...
  • Page 69 ASSEMBLY INSTRUCTIONS 7-PIN 4-PIN CIRCUIT WIRE COLOR CONN. TOWER GROUND WHITE – WORK LAMPS BLACK LEFT FLASHING YELLOW & TURN – STOP LAMPS RIGHT FLASHING GREEN & TURN TAIL LAMPS BROWN SWITCHED – BLUE POWER (12 V) MAIN WARNING LIGHT HARNESS - WIRING CHART 2-PIN 3-PIN 6-PIN...

  • Page 70: Led Light Installation

    ASSEMBLY INSTRUCTIONS LED Light Installation 6. Install the rear warning light harness to the frame. Connect 2 pin and 3 pin ends to each of the warning 1. Attach LH and RH light bracket assemblies to center lights. Connect 6 pin to the ag flasher control module. frame using 5/8-11 x 6-11/16 x 5-1/2 u-bolt and 5/8 See Figures 3-24 for harness wire designations.
  • Page 71 ASSEMBLY INSTRUCTIONS REAR HARNESS AG FLASHER REFLECTOR LED AMBER CONTROL MOUNT 1/4-20 X 1 LIGHT MODULE HEX SCREW 1/4-20 X 1-1/2 ASSEMBLY RH & LOCK NUT HEX SCREW & LOCK NUT MOUNTING RED AG BRACKET LAMP 1/2-13 X 5-1/2 HEX SCREW &...
  • Page 72 ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: 3-38 F-1072-0320...

  • Page 73: Operation And Maintenance

    Chapter 4 Operation and Maintenance   DANGER DANGER Never allow anyone to ride on the 877 Tilloll at Always lock the tractor drawbar in the center any time. Allowing a person to ride on the position when transporting the unit. Failure to do machine can inflict serious personal injury or so can result in serious injury or death and cause death to that person.

  • Page 74: Tractor Preparation

    OPERATION AND MAINTENANCE Tractor Preparation The Landoll 877 Tilloll is designed to be pulled by tractor 1/2 FLANGE equipped with a double lip or clevis type hitch. If your LOCK NUT tractor is not equipped as such, you need to purchase the hitch from your local tractor dealer.

  • Page 75: Hydraulic Lift System

    OPERATION AND MAINTENANCE Hydraulic Lift System 3. Always fully extend the cylinders and hold the lever to ensure the cylinders are rephased before starting The Tilloll is equipped with a rephasing hydraulic lift any field operation. This will keep all cylinders in time system to raise and lower the unit in the field.

  • Page 76: Hydraulic Fold System

    OPERATION AND MAINTENANCE Hydraulic Fold System  WARNING 1. The Tilloll is equipped with a hydraulic fold system to Escaping hydraulic fluid can cause serious raise and lower the wing frames for narrow transport. personal injury. Relieve system pressure before 2.

  • Page 77: General Operation

    OPERATION AND MAINTENANCE General Operation 3. Check the front to rear leveling of the frame. Adjust radius rod until frame is level at working depth and all 1. The horsepower requirements are typically 8-10 sections of the machine are cutting at the same horsepower per foot of cut.

  • Page 78: Leveling (Side To Side)

    OPERATION AND MAINTENANCE Leveling (Side to Side) Leveling (Front-to-Rear) 1. The mainframe and wings must always be level side 1. The leveling feature on the Tilloll is used to keep the to side during operation. To level the wings with the machine level in the working position only.

  • Page 79: Disc Blades

    OPERATION AND MAINTENANCE Disc Blades  DANGER 1. The Tilloll is equipped with full concavity disc blades. Disc blades are extremely sharp. Exercise These blades measure 20” in diameter and have 2” extreme care when working on or near disc of concavity.

  • Page 80: Scraper Adjustment

    OPERATION AND MAINTENANCE Scraper Adjustment 2. When adjusting or assembling the spring assembly, tighten the upper spring bolt, but leave The Tilloll is equipped with rigid scrapers at regular disc approximately1/4” gap above the spring jam nut spools with dual scrapers at the disc bearings. Figure 4-11.

  • Page 81: Spray Shield Adjustment

    OPERATION AND MAINTENANCE Spray Shield Adjustment Reel Adjustment 1. The spray shields directly behind the disc gang have 1. The reel is preset at the factory at the correct angle. two uses and can be adjusted accordingly. This angle is set to move worked soil back to the center of the implement.

  • Page 82: Harrow Adjustment

    OPERATION AND MAINTENANCE Harrow Adjustment c. Spring tension can be increased by lowering the rear mounting point of the two lower springs and 1. The harrow on the rear of the machine can be set for raising the front mounting point of the upper a variety of field conditions See Figure 4-12.
  • Page 83 2. Remove the tire. replace all seals. Seal kits are available from your 3. Remove the hub cap, cotter pin, slotted nut and Landoll dealer. washer. 3. Check all hydraulic hoses weekly. Look for binding or 4. Remove the hub. Clean and inspect the bearings and cracking.
  • Page 84 OPERATION AND MAINTENANCE Transport 1. Check and follow all federal, state, and local requirements before transporting the Tilloll. 2. The 877 should be transported only by tractor required for field operation. The implement weight should not exceed more than 1.5 times the tractor SAFETY weight.

  • Page 85: 2 X 8 Transport

    OPERATION AND MAINTENANCE  WARNING 2 X 8 TRANSPORT LOCKOUT Failure to use transport locks during transport may result in permanent equipment damage, 1-8 HAIR serious injury, or death. L PIN 11. Transport during daylight hours whenever possible. Always use flashing warning lights, except where such use is prohibited by law.

  • Page 86: Lubrication Maintenance

    OPERATION AND MAINTENANCE Lubrication Maintenance 4. Wheel seals, when properly installed, will allow grease to pass without harm to seals. Regular 1. A proper maintenance schedule will insure a long lubrication will extend service life, particularly in operating life and peak performance. Performing the severe operating conditions.
  • Page 87 OPERATION AND MAINTENANCE Figure 4-16: Lubrication Schedule LUBRICATION TABLE INTERVAL ITEM DESCRIPTION NO. OF LUBE POINTS (Hours Unless Stated) Radius Rod Lift Pivot Pin Walking Tandem Pivots 1 each - 4 total Wheel Hubs 1 each - 8 total Chopper Reel Bearings 1 each Table 4-1: Lubrication Table 4-15...

  • Page 88: Storage

    OPERATION AND MAINTENANCE Storage 2. Store the unit in a shed or under a tarpaulin to protect it from the weather. The ground tools and tires should 1. The service life of the Tilloll will be extended by rest on boards, or some other object, to keep them proper off-season storage practices.

  • Page 89: Troubleshooting Guide

    Chapter 5 Troubleshooting Guide The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can happen using your 877 Tilloll. Follow all safety precautions stated in the previous sections when making any adjustments to your machine. PROBLEM PROBABLE CAUSE SOLUTION...
  • Page 90 TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE SOLUTION SHANK SPRINGS BREAKING Spring pivot bolt too tight Spring pivot bolt must be loose enough to allow spring plug to pivot so spring is not forced to bend. SCREW IN TOP OF SPRING Lock nut should be tightened against Verify that there are three threads BREAKING shank bracket instead of spring plug...
  • Page 91 TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE SOLUTION ROCKS JAMMING IN END OF REEL Reel blade too long Cut 1-1/2" off the end of reel blade. AND LOCKING UP REEL Reel angle wrong for terrain Cut blade off at angle toward rear of blade to provide a relief area for rocks.
  • Page 92 TROUBLESHOOTING GUIDE Table provided for general use. NOTES: F-1072-0320...
  • Page 93 Document Control Revision Log: Date Form # Improvement(s): Description and Comments 02/14/2020 F-1072 Initial Release 03/20/2020 F-1072-0320 New Manual...
  • Page 94 Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Model 877 Tilloll Operator Manual Re-Order Part Number F-1072-0320 LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM Copyright 2020.

Table of Contents