Related Manuals for Landoll Brillion CPP7
Summary of Contents for Landoll Brillion CPP7
- Page 1 Chisel Plow, 3 - Bar Mounted Models: CPP7 through CPP12 Operator’s Manual LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM 175rev1113 7D525...
-
Page 3: Table Of Contents
Table of Contents Introduction and Safety Information Introduction ..............1-1 Description of Unit . - Page 4 Maintenance General Torque Specifications ..........4-1 Fasteners .
-
Page 5: Introduction And Safety Information
Failure to comply with this warning can result in within 10 days of retail purchase, using the Landoll to the personal injury or death, damage Corporation Ag Products on-line registration process. -
Page 6: Safety
INTRODUCTION AND SAFETY INFORMATION Safety When applying decals to the implement, be sure to clean the surface to remove any dirt or residue. Where possible, sign placement should protect the sign from NOTE abrasion, damage, or obstruction from mud, dirt, oil etc. Investigation has shown that nearly 1/3 of all farm ... -
Page 7: Maintenance Safety
INTRODUCTION AND SAFETY INFORMATION Maintenance Safety • Block the implement so it will not roll when working on or under it to prevent injury. • Do not make adjustments or lubricate the machine while it is in motion. • Make sure all moving parts have stopped. •... -
Page 8: Decals
INTRODUCTION AND SAFETY INFORMATION Decals Figure 1-2: Decals and Locations 7D525... - Page 9 INTRODUCTION AND SAFETY INFORMATION Figure 1-3: 7 and 9 Shank Model Decal Locations...
- Page 10 INTRODUCTION AND SAFETY INFORMATION Figure 1-4: 10 and 12 Shank Model Decal Locations 7D525...
- Page 11 INTRODUCTION AND SAFETY INFORMATION Figure 1-5: 11 Shank Decal Locations...
- Page 12 INTRODUCTION AND SAFETY INFORMATION Table provided for general use. NOTES: 7D525...
-
Page 13: Assembly
Chapter 2 Assembly Main Frame Assembly CAUTION 1. Place the frame on blocks at least 36-42 inches high Do not work on or under this machine unless for the assembly of the machine. securely blocked and supported by a hoist or 2. - Page 14 ASSEMBLY Figure 2-1: Frame 7D525...
-
Page 15: Frame Assembly Dimensions
ASSEMBLY Frame Assembly Dimensions “Left” and “Right” refer to directions seen as if standing behind the machine and facing in the direction of forward travel. Figure 2-2: Frame Assembly Dimensions... - Page 16 ASSEMBLY Figure 2-3: Upper and Lower Hitch Pin Positions 7D525...
- Page 17 ASSEMBLY Figure 2-4: Lower Hitch Orientation...
-
Page 18: Ft Frame Extensions
ASSEMBLY 1 Ft Frame Extensions Install a 1 Ft Frame Extensions on each 4-Hole Plate on the outer tubes of the Frame with 5/8-11 x 2 Bolts, Lockwashers and Nuts. Figure 2-5: 1 Ft Extensions 7D525... - Page 19 ASSEMBLY 2 Ft Frame Extensions Install a 2 Ft Frame Extensions on each 4-Hole Plate on the outer tubes of the Frame with 5/8-11 x 2 Bolts, Lockwashers and Nuts. Secure the front of the extension by placing a 4-hole plate on the inside of the frame tube. Secure with 5/8-11 x 5 Bolts, Lockwashers and Nuts.
-
Page 20: Shank Installation
ASSEMBLY Shank Installation Shank Assemblies are shipped with all the necessary hardware to mount the shanks to the frame. Attach the Shank Assemblies to the frame in the locations indicated in Figure 2-7 through 2-12. Figure 2-7: CPP7 Shank and Shovel Locations 7D525... - Page 21 ASSEMBLY Figure 2-8: CPP9 Shank and Shovel Locations...
- Page 22 ASSEMBLY Figure 2-9: CPP10 Shank and Shovel Locations 2-10 7D525...
- Page 23 ASSEMBLY Figure 2-10: CPP11 Shank and Shovel Locations 2-11...
- Page 24 ASSEMBLY Figure 2-11: CPP12 Shank and Shovel Locations 2-12 7D525...
-
Page 25: Spring Clamp Shank Assembly
ASSEMBLY Spring Clamp Shank Assembly Rigid Clamp Shank Assembly Remove the 3/4-10 U-Bolts, Lockwashers and Nuts. Remove the front 3/4-10 x 7-1/2 Bolt, Lockwasher and Place Shank Assembly Clamp under the frame and Nut and loosen the 5/8-11 Nuts so that they are flush with re-insert the U-Bolts over the top of the frame and the end of the Bolt. -
Page 26: Point Installation
ASSEMBLY Point Installation NOTE When replacing or reversing points, change all points at the same time so that they will have the same operating depth. If some shanks have worn points, or points of a different design, the chisel plow will not operate efficiently. -
Page 27: Optional Gauge Wheels Kits
ASSEMBLY Optional Gauge Wheels Kits Place Gauge Wheel Arm between the bar stock that is welded to the 4-Hole Plate on the inside of the outer Frame Tube. Attach Gage wheel to frame with 4-hole plate, 5/8-11 x 3 Bolts, Lockwashers and Nuts. See Figure 2-17. -
Page 28: Led Warning Lights
ASSEMBLY LED Warning Lights Installation NOTE All models similar. Refer to Figure 2-19 for bracket and light placement. 1. Attach the 2 (two) Light Brackets to the rear frame using the 1/2-13 U-Bolts and Nuts. On the 11’ Models the Light Brackets are attached the 2 (two) foot extensions. - Page 29 ASSEMBLY LED Warning Lights Schematic Figure 2-18: LED Warning Lights Schematic 2-17...
- Page 30 ASSEMBLY Figure 2-19: Electrical Installation Dimensions 2-18 7D525...
- Page 31 ASSEMBLY Figure 2-20: 7’ and 9’ LED Warning Lights Layout 2-19...
- Page 32 ASSEMBLY Figure 2-21: 10’ and 12’ LED Warning Lights Layout 2-20 7D525...
- Page 33 ASSEMBLY Figure 2-22: 11’ LED Warning Lights Layout 2-21...
- Page 34 ASSEMBLY Table provided for general use. NOTES: 2-22 7D525...
-
Page 35: Operation
The rear tractor tires should be inflated equally This chapter will cover the basic operation and and ballast added according to the tractor procedures for the Landoll Brillion Chisel Plow. Be sure to operator’s manual. read and understand the Safety Procedures and b. -
Page 36: Field Operation - Three Point Hitch Type
OPERATION 3. For tractors equipped with Quick Hitches: a. Attach quick hitch to the Chisel Plow a. Set shank depth by adjusting the max depth stop on the 3-Point Control in the tractor. b. Raise and make sure lower pin locks are secured. -
Page 37: Transport
OPERATION Transport Reflectors and SMV Sign 1. Check and follow all federal, state, and local Reflectors and a slow moving vehicle sign (SMV) are requirements before transporting the Chisel Plow. required if the Chisel Plow is transported on a public road. - Page 38 OPERATION Table provided for general use. NOTES: 7D525...
-
Page 39: Maintenance
Chapter 4 Maintenance General Torque Specifications (rev. 4/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used. -
Page 40: Fasteners
MAINTENANCE Fasteners Before operating your Brillion machine, check all hardware for tightness. Use the Tightening Torque Table below as a guide. See Page 4-1. After a few hours of use, check entire machine and tighten any loose nuts or bolts. Daily or periodic checks should be made thereafter. -
Page 41: Storage
MAINTENANCE NOTE When replacing or reversing points, change all points at the same time so that they will have the same operating depth. If some shanks have worn points, or points of a different design, the chisel plow will not operate efficiently. - Page 42 MAINTENANCE Table provided for general use. NOTES: 7D525...
-
Page 43: General Reference And Specifications
Chapter 5 General Reference and Specifications... -
Page 44: General
GENERAL REFERENCE AND SPECIFICATIONS 7D525... - Page 45 Document Control Revision Log: Date Revision Improvement(s) Description and Comments 07/2001 Initial Release 11/2013 1113 Updated to the Landoll format. Added LED Warning Lights...
- Page 46 Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Chisel Plow, 3 - Bar Mounted Models: CPP7 through CPP12 Operator’s Manual Re-Order Part Number 7D525 LANDOLL CORPORATION 1900 North Street...