Related Manuals for Landoll 876 Series
Summary of Contents for Landoll 876 Series
- Page 1 MODEL 876 SERIES WING TILLOLL OPERATOR’S MANUAL 1900 NORTH STREET MARYSVILLE, KANSAS 66508 (785) 562-5381 F-143-0803 08/03...
- Page 2 LANDOLL will not be liable for labor, transpor- tation, or any other charges resulting from replacement of a defective part. This warranty is void if any part not supplied by LANDOLL is used in assembly or repair, or if the machine has been altered, abused, or neglected.
- Page 3 MODEL 876 WING SERIES TILLOLL OPERATOR’S MANUAL PURCHASED FROM: DATE ADDRESS: PHONE NO.: SERIAL NO.:...
-
Page 5: Table Of Contents
TABLE OF CONTENTS SECTION DESCRIPTION PAGE NO. INTRODUCTION ........1-1 STANDARD SPECIFICATIONS . - Page 6 SAFETY PRECAUTIONS THIS IS THE SAFETY ALERT SYMBOL. IT IS USED TO ALERT YOU TO POTENTIAL INJURY HAZARDS. OBEY ALL SAFETY MESSAGES THAT FOLLOW THIS SYMBOL TO AVOID POSSIBLE INJURY OR DEATH. DANGER DANGER INDICATES AN IMMINENTLY HAZARDOUS SITUA- TION WHICH, IF NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.
-
Page 7: Introduction
INTRODUCTION The Landoll 876 Wing Series Tilloll is a quality product designed to give years of trouble free perform- ance. By following each section of this manual, your system will perform as designed for you and your op- eration. SECTION 1 gives basic instructions on the use of this manual. -
Page 9: Standard Specifications
STANDARD SPECIFICATIONS SIZE WIDTH TRANSPORT NO. OF NO. OF APPROX. OF CUT WIDTH SHANKS 20" DISC WEIGHT BLADES LBS. 876-30 30’-0" 16’-6" 12,170 876-35 34’-6" 9’-0" 16,700 876-40 39’-0" 18’-0" 18,700... - Page 10 LANDOLL CORPORATION GENERAL TORQUE SPECIFICATIONS (REV. 4/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR GENERAL PURPOSE APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED NUTS AND CAPSCREWS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS RECEIVED CONDITION).
- Page 11 LANDOLL CORPORATION HYDRAULIC FITTING TORQUE SPECIFICATIONS JIC, ORS, & ORB (REV. 10/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR HYDRAULIC FITTING APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED CARBON STEEL AND STAINLESS STEEL FITTINGS ASSEMBLED WITHOUT SUPPLEMENTAL...
- Page 12 Figure 2-1 876-30 Shank Placement Assembly (1 of 2)
- Page 13 Figure 2-2 876-30 Shank Placement Assembly (2 of 2)
- Page 14 Figure 2-3 876-35 Shank Placement Assembly (1 of 2)
- Page 15 Figure 2-4 876-35 Shank Placement Assembly (2 of 2)
- Page 16 Figure 2-5 876-40 Shank Placement Assembly (1 of 2)
- Page 17 Figure 2-6 876-40 Shank Placement Assembly (2 of 2)
- Page 18 NOTES: 2-10...
-
Page 19: Assembly Instructions
ASSEMBLY INSTRUCTIONS DANGER It is very important that your new 876 Wing Se- ries Tilloll be properly assembled, adjusted and lu- bricated before use. Illustrations to assist with the TO PREVENT ACCIDENTAL LOWER- assembly process are provided in Section 2, ING: “Standard Specifications”. - Page 20 Figure 3-1 Frame, Wing, and Extension Assembly...
- Page 21 Figure 3-2 Frame, Wing, and Extension Assembly...
- Page 22 Figure 3-3 Frame, Wing, and Extension Assembly...
-
Page 23: Frame And Wing Assembly
3-1 FRAME AND WING ASSEMBLY IMPORTANT 3-1.6 On 40’ models, connect wing frame ex- tensions to wings using 5/8-11 x 1-1/2 hex READ ALL SAFETY PRECAUTIONS AT THE head cap screws and hex lock nuts (See FRONT OF THE SECTION BEFORE ATTEMPT- Figure 3-3). - Page 24 Figure 3-4 Shank, Clamp, and Sweep Assembly...
-
Page 25: Shank, Clamp, And Sweep Assembly
3-2 SHANK, CLAMP, AND SWEEP ASSEMBLY 3-2.2 Install danish sweep to center shank as- IMPORTANT sembly using 3/8-16 x 1-1/2 plow bolt and hex lock nut. READ ALL SAFETY PRECAUTIONS AT THE 3-2.3 Install shanks in clamps. FRONT OF THE SECTION BEFORE ATTEMPT- a. - Page 26 Figure 3-5 Hydraulic Lift Assembly...
-
Page 27: Hydraulic Lift Installation
3-4 HYDRAULIC LIFT INSTALLATION IMPORTANT NOTE: Mount check valve so that the ports V1 and V2 are facing the divider valve with V1 port READ ALL SAFETY PRECAUTIONS AT THE behind the V2 port. Install hose A in V1 port of FRONT OF THE SECTION BEFORE ATTEMPT- each check valve and connect to swivel adapt- ING ANY OF THE FOLLOWING PROCEDURES. - Page 28 Figure 3-6 Hydraulic Fold Assembly 3-10...
-
Page 29: Hydraulic Fold Installation
3-5 HYDRAULIC FOLD INSTALLATION IMPORTANT 3-5.1 Install wing fold bracket to wing hinge using 1-8 x 7-1/2 hex head cap screw READ ALL SAFETY PRECAUTIONS AT THE through bracket, wing hinge, second bracket, FRONT OF THE SECTION BEFORE ATTEMPT- and hex lock nut. Install base end of fold cyl- ING ANY OF THE FOLLOWING PROCEDURES. - Page 30 Figure 3-7 Disc Gang and Spray Shield Installation 3-12...
-
Page 31: Disc Gang And Spray Shield Installation
3-6 DISC GANG AND SPRAY SHIELD INSTALLATION IMPORTANT IMPORTANT READ ALL SAFETY PRECAUTIONS AT THE DISC ROD AND SLOTTED NUT SHOULD BE FRONT OF THE SECTION BEFORE ATTEMPT- TIGHTENED TO A TORQUE OF 1200 FT. LB. ING ANY OF THE FOLLOWING PROCEDURES. THIS IS EQUIVALENT TO A 200 LB. - Page 32 Figure 3-8 Reel Assembly Installation 3-14...
-
Page 33: Reel Assembly Installation
3-7 REEL ASSEMBLY INSTALLATION IMPORTANT 3-7.1 Loosely bolt center reel shank assembly to frame in position shown in Figure 3-8 us- DISTANCE BETWEEN REEL BLADE ing 5/8-11 x 8 hex head cap screws and hex SHANK SHOULD BE 1 INCH. lock nuts (See Figures 2-1 through 2-6 for 3-7.5 Reel bearings lock collars should be in-... - Page 34 Figure 3-9 Harrow Assembly Installation 3-16...
-
Page 35: Harrow Assembly Installation
3-8 HARROW ASSEMBLY INSTALLATION 3-8.1 Install harrow hanger arms to rear of 3-8.4 Install harrow springs and chains as frame using u-bolts and 5/8-11 hex lock nuts shown in Figure 3-9 using 1/2-13 x 4 hex (See Figures 2-1 through 2-4 for loca- head cap screws and hex lock nuts. - Page 36 Figure 3-10 Pull Hitch Installation 3-18...
-
Page 37: Pull Hitch Installation
3-9 PULL HITCH INSTALLATION IMPORTANT IMPORTANT SEE FIGURE 3-10 FOR PART NAMES. THE RADIUS ROD AFFECTS TWO ADJUST- 3-9.1 Install pull hitch assembly to frame us- MENTS: ing hitch pins, flat washers, and 1/4 x 2-1/2 IT LOCATES THE PULL HITCH CLEVIS AT cotter pins. - Page 38 Figure 3-11 Electrical Installation 3-20...
-
Page 39: Warning Lights Installation
3-10 WARNING LIGHTS INSTALLATION 3-10.5 Assemble warning light bar and warning 3-10.1 Assemble lights to the warning light light bracket assembly to outer rear of frame bracket using 1/4-20 X 1-1/4 hex head cap as shown in Figure 3-11 using 1/2-13 x screws and hex lock nuts. - Page 40 Figure 3-12 Decal Installation 3-22...
-
Page 41: Lubrication
If any decals become unreadable, or are destroyed during use, get re- placement decals from your Landoll dealer as soon as possible, and replace them on the machine. 3-23... - Page 42 NOTES: 3-24...
-
Page 43: Operation And Maintenance
OPERATION AND MAINTENANCE DANGER DANGER NEVER ALLOW ANYONE TO RIDE ON ALWAYS LOCK THE TRACTOR DRAW- THE 876 WING SERIES TILLOLL AT BAR IN THE CENTER POSITION WHEN ANY TIME. ALLOWING A PERSON TO TRANSPORTING THE UNIT. FAILURE RIDE ON THE MACHINE CAN INFLICT TO DO SO CAN RESULT IN SERIOUS SERIOUS PERSONAL INJURY OR INJURY OR DEATH AND CAUSE DAM-... -
Page 44: Tractor Preparation
TRACTOR PREPARATION 4-1.1 Inflate the rear tractor tires equally and The Landoll 876 Wing Series Tilloll is designed add ballast according to the tractor opera- to be pulled by tractor equipped with a double lip tor’s manual. or clevis type hitch. If your tractor is not equipped 4-1.2... -
Page 45: Attaching To The Tractor
4-3 ATTACHING TO THE TRACTOR 4-3.3 Lower to the ground when the control 4-3.1 Align the tractor drawbar with the ma- arm is moved forward or downward, and chine. Raise or lower the Tilloll ring hitch, as 4-3.4 Raise when the control arm is moved needed, using the swivel jack. -
Page 46: Field Operation
Figure 4-2 Transport Locks 4-5 FIELD OPERATION IMPORTANT 4-5.1 Raise the unit to take the weight off of the transport locks. Remove the transport WHEN FOLDING OR UNFOLDING WINGS, OP- locks from the lift cylinders (on the main ERATE TRACTOR ENGINE AT A FAST IDLE ON frame only). -
Page 47: Disc Gang Scraper Adjustment
4-5.3 Check the front to rear leveling of the frame. Adjust radius rod until frame is level at working depth and all sections of the ma- chine are cutting at the same depth (See Figure 4-3). 4-5.4 Set the unit working depth (1 - 5 inches) by adjusting the stroke control on the master cylinder. -
Page 48: Spray Shield Adjustment
4-7 SPRAY SHIELD ADJUSTMENT 4-7.5 The shields should also be set at an an- 4-7.1 The spray shields directly behind the gle to carry some soil back to the center of disc gang have two uses and can be ad- the machine as it levels the soil. -
Page 49: Harrow Adjustment
Figure 4-4 Harrow Adjustment 4-10 HARROW ADJUSTMENT 4-10.1 The harrow on the rear of the machine c. Spring tension can be increased by lowering can be set for a variety of field conditions. the rear mounting point of the two lower The harrow is set up according to the as- springs and raising the front mounting point of sembly instructions for a working depth of 3 -... - Page 50 Figure 4-5 Lubrication Points GENERAL ASSEMBLY ITEM DESCRIPTION LUBE POINT NO. INTERVAL (Hours unless stated) Radius rod Gauge wheel pivot pin Disc gang bearing Reel bearing Walking beams Yearly Wheel bearing Yearly Table 4-1 Lubrication Schedule...
-
Page 51: Wheel Bearing Maintenance
4-11 WHEEL BEARING MAINTENANCE 4-11.4 Repack the bearings using a high- Wheel bearing maintenance should be per- quality wheel bearing grease. formed at the beginning of every season of use. 4-11.5 Replace the hub with a new seal and Check the wheel bearings periodically for exces- the inner bearing in place. -
Page 52: Storage
4-14 STORAGE 4-14.5 Grease all exposed metal surfaces of 4-14.1 The service life of the Tilloll will be ex- shanks, points and discs. tended by proper off-season storage prac- 4-14.6 Lubricate each point of the machine as tices. Prior to storing the unit, complete the stated in Section 4-13. - Page 53 NOTES 4-11...
-
Page 55: Troubleshooting Guide
TROUBLESHOOTING GUIDE The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can hap- pen using your 876 Wing Series Tilloll. Follow all safety precautions stated in the previous when making any adjustments to your machine. PROBLEM PROBABLE CAUSE:SOLUTION 1. - Page 56 PROBLEM PROBABLE CAUSE:SOLUTION 5. PLUGGING BETWEEN DISC AND SPRAY A. DIRT NOT FLOWING UNDER SHIELD: SHIELD Readjust spray shield (usually up and/or to the rear). Machine running too deep. Raise to proper operating depth by adjusting stroke control depth stop on master cylinder.
- Page 57 PROBLEM PROBABLE CAUSE:SOLUTION 14. ROCKS JAMMING IN END OF REEL AND A. REEL BLADE TOO LONG: LOCKING UP REEL Cut 1-1/2" off the end of reel blade. B. REEL ANGLE WRONG FOR TERRAIN: Cut blade off at angle toward rear of blade to provide a relief area for rocks.
- Page 58 NOTES:...