Yamaha 007POTO-G0 Owner's Manual page 73

9
If you want to use the MONO bus, make
sure that the [ON] key of the MONO channel
is turned on, and raise the fader of the
MONO channel to an appropriate position.
This operation will differ between the LS9-16 and
LS9-32.
●
For the LS9-16
Assign the MONO channel to the custom fader layer,
press the LAYER [CUSTOM] key to access the cus-
tom fader layer, and then operate the [ON] key and
fader of the corresponding channel module.
●
For the LS9-32
Press the LAYER [MASTER] key to access the master
fader layer, and operate the [ON] key and fader of
channel module 32.
10
Select the master fader layer, make sure
that the [ON] key of the desired MIX channel
is turned on, and raise the fader to an
appropriate position.
The following steps will differ depending on whether
you selected a ST/MONO mode MIX channel or an
LCR mode MIX channel in step 6.
● For a MIX channel set to ST/MONO
mode
11
Use the ST button and MONO button in the
TO STEREO/MONO popup window as on/off
switches for the signal sent from the MIX
channel to the STEREO bus and MONO
bus.
12
Use the SELECTED CHANNEL section
[PAN] encoder to adjust the pan/balance of
the signal sent from the MIX channel to the
STEREO bus.
You can obtain the same result by using the TO ST
PAN/TO ST BALANCE knob in the TO STEREO/
MONO popup window.
● For a MIX channel set to LCR mode
11
Use the LCR button in the TO STEREO/
MONO popup window as an on/off switch
for the signal sent from the MIX channel to
the STEREO bus and MONO bus.
For a MIX channel that is set to LCR mode, the signal
sent to the STEREO bus and MONO bus can be
switched on/off in a single operation.
12
Use the CSR knob in the TO STEREO/MONO
popup window to adjust the proportion
between the signal level sent from that MIX
channel to the STEREO (L/R) bus and the
signal level sent to the MONO (C) bus.
Sending signals from MIX channels to the STEREO/MONO bus
13
Use the TO ST PAN knob in the TO STEREO/
MONO popup window to set the panning of
the signal sent from the MIX channel to the
STEREO (L/R) bus and the MONO (C) bus.
If the CSR knob is set to 0%, operating the TO ST
PAN knob of a MIX channel will change the signal
levels sent to the STEREO (L/R) bus and MONO (C)
bus as shown in the following illustration. In this case,
the TO ST PAN knob will operate as a conventional
PAN knob, and no signal is sent to the MONO (C) bus.
L C
TO ST PAN knob
If a MIX channel set to stereo is selected, operating
the TO ST BALANCE knob will change the signal
levels sent from the MIX channel to the STEREO (L/
R) bus and MONO (C) bus as shown in the following
illustration. In this case, the [PAN] encoder will oper-
ate as a conventional BALANCE knob, and no signal
is sent to the MONO (C) bus.
L C
TO ST BALANCE knob
L C
TO ST BALANCE knob
Signal sent to the
STEREO (L) bus
Signal sent to the
STEREO (R) bus
R
Signal sent from the
odd-numbered MIX
channel to the STE-
REO (L) bus
R
Signal sent from the
even-numbered MIX
channel to the STE-
REO (R) bus
R
LS9-16/32 Owner's Manual
6
73