Yamaha 007POTO-G0 Owner's Manual page 76

Sending signals from MIX channels and STEREO/MONO channels to MATRIX buses
3
Use the MIX/MATRIX SELECT section keys
to select the send-destination MATRIX bus.
When a MIX, STEREO (L/R), or MONO channel is
selected, the keys of the MIX/MATRIX SELECT sec-
tion are used to select the send-destination MATRIX
bus.
When you press a key to select the send-destination
MATRIX bus, only the LED of the corresponding key
will blink, indicating that it is selected as the send-des-
tination. The cursor will move to the corresponding
TO MATRIX LEVEL knob in the TO MATRIX field
of the screen.
NOTE
• If a MIX, STEREO (L/R), or MONO channel is selected, MIX/
MATRIX SELECT section keys 9–16 are inactive.
• If the LED of only the specified key is blinking in the MIX/
MATRIX SELECT section and the LEDs of the remaining keys
are lit, the LS9 is in SENDS ON FADER mode. Press the
desired key of the MIX/MATRIX SELECT section so that only
the LED of that key is blinking.
4
Use the SELECTED CHANNEL section
[SELECTED SEND] encoder to adjust the
send level from that channel to the MATRIX
bus you selected in step 3.
If the send-destination MATRIX bus is set to stereo,
the function of the [SELECTED SEND] encoder will
change depending on which of the two adjacent keys
of the MIX/MATRIX SELECT section are lit.
●
If the left key is lit
Use the [SELECTED SEND] encoder to adjust the
pan (or balance, for a STEREO channel) of the signal
that is sent from that channel to the two MATRIX
buses.
●
If the right key is lit
Use the [SELECTED SEND] encoder to adjust the
send level shared by the two MATRIX buses.
5
To switch the on/off status of a signal sent
to a MATRIX bus, move the cursor to the TO
MATRIX LEVEL knob in the screen and
press the [ENTER] key.
If you switch this off, the knob will turn grey. To turn
it back on, press the [ENTER] key once again.
6
Use the top panel [SEL] keys to select
another channel, and adjust the send level
to the selected MATRIX bus in the same
way.
7
Use the keys of the MIX/MATRIX SELECT
section to select another MATRIX bus as
the send-destination, and adjust the send
level in the same way.
76
LS9-16/32 Owner's Manual
HINT
• If PRE is selected as the send position to the MATRIX bus,
then you will also be able to select either PRE EQ (immedi-
ately before the attenuator) or PRE FADER (immediately
before the fader) for each two adjacent odd-numbered/even-
numbered MATRIX buses ( → p. 213).
• If desired, the pan/balance setting of the signal sent to a ste-
reo MATRIX bus can be linked with the TO ST PAN/TO ST
BAL knob of the SELECTED CH VIEW screen ( → p. 213).
• If you want to monitor the signal that is being sent to a specific
MATRIX bus, select the fader layer that includes that MATRIX
channel, and press the corresponding [CUE] key.
■ Controlling the signals sent from MIX, STE-
REO (L/R), or MONO channels to a specific
MATRIX bus
1
Press the SELECTED CHANNEL section
[HOME] key.
The SELECTED CH VIEW screen will appear in the
display.
2
Use the LAYER section keys and the [SEL]
keys of the channel module section to
select the send-destination MATRIX chan-
nel.
The SELECTED CH VIEW screen will change as fol-
lows.
1
2
1 FROM MIX field
If a MATRIX channel is selected, this area of the
SELECTED CH VIEW screen will show the FROM
MIX field, allowing you to switch the on/off status and
adjust the send level of the signals sent from each MIX
channel to the MATRIX bus.
B FROM MIX LEVEL knobs
These knobs indicate and control the send level of the
signals sent from MIX channels 1–16 to the currently
selected MATRIX bus.
HINT
• In order to select a MATRIX channel on the LS9-16, you must
first select the custom fader layer to which you've assigned
that MATRIX channel, and then press the corresponding
[SEL] key.